HIK VISION DS-2CC102P-IRA User manual

IR Bullet Camera·User Manual
0
0
IR Bullet Camera
User Manual
UD.6L0201D0063A01

IR Bullet Camera·User Manual
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
This manual applies to following cameras:
Models
Models
DS-2CC102P(N)-IR1(IR3)
(IR5)
DS-2CC112P(N)-IR1(IR3)
(IR5)
DS-2CC192P(N)-IR1(IR3)
(IR5)
DS-2CC1182P(N)-IR1(IR3)
(IR5)
DS-2CC1192P(N)-IR1(IR3)
(IR5)
DS-2CC11A2P(N)-IR1(IR3)
(IR5)
DS-2CC1172P(N)-IR1T
(IR3T)(IR5T)
DS-2CC1182P(N)-IR1T
(IR3T)(IR5T)
DS-2CC102P(N)-IRA
DS-2CC112P(N)-IRA
DS-2CC192P(N)-IRA
DS-2CC1182P(N)-IRA
DS-2CC1192P(N)-IRA
DS-2CC11A2P(N)-IRA
DS-2CC102P(N)-IR
DS-2CC112P(N)-IR
DS-2CC192P(N)-IR
DS-2CC1132P(N)-IR

IR Bullet Camera·User Manual
2
2
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice .
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.”
0100001021012

IR Bullet Camera·User Manual
3
3
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies w ith part 15 of the FCC Rules. Operation is
subject to the following two condit ions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.

IR Bullet Camera·User Manual
4
4
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked w ith this
symbol, which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.

IR Bullet Camera·User Manual
5
5
Safety Warnings and Cautions
Please pay attention to the following warnings and
cautions:
Hazardous Voltage may be present: Special
measures and precautions must be taken when
using this device. Some potentials (voltages) on the
device may present a hazard to the user. This device
should only be used by Employees from our company with
knowledge and training in working with these types of devices that
contain live circuits.
Power Supply Hazardous Voltage: AC mains voltages
are present within the power supply assembly. This device must be
connected to a UL approved, completely enclosed power supply, of
the proper rated voltage and current. No user serviceable parts
inside the power supply.
System Grounding (Earthing): To avoid shock, ensure
that all AC wiring is not exposed and that the earth grounding is

IR Bullet Camera·User Manual
6
6
maintained. Ensure that any equipment to which this device will be
attached is also connected to properly wired grounded receptacles
and are approved medical devices.
Power Connect and Disconnect: The AC
power supply cord is the main disconnect device to
mains (AC power).The socket outlet shall be
installed near the equipment and shall be readily
accessible.
Installation and Maintenance: Do not connect/disconnect
any cables to or perform installation/maintenance on this device
during an electrical storm.
Power Cord Requirements: The connector
that plugs into the wall outlet must be a
grounding-type male plug designed for use in your
region. It must have certification marks showing certification by an
agency in your region. The connector that plugs into the AC
receptacle on the power supply must be an IEC 320, sheet C13,
female connector. See the following website for more information
http://kropla.com/electric2.htm.
Lithium Battery: This device contains a Lithium Battery. There
is a risk of explosion if the battery is replaced by an incorrect type.

IR Bullet Camera·User Manual
7
7
Dispose of used batteries according to the vendor’s instructions
and in accordance with local environmental regulations.
Perchlorate Material: Special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. This notice is
required by California Code of Regulations, Title 22, Division 4.5,
Chapter 33: Best Management Practices for Perchlorate Materials.
This device includes a battery which contains perchlorate material.
Taiwan battery recycling:
Please recycle batteries.
Thermal and Mechanical Injury: Some
components such as heat sinks, power regulators,
and processors may be hot; care should be taken
to avoid contact with these components.
Electro Magnetic Interference: This equipment has not
been tested for compliance with emissions limits of FCC and similar
international regulations. This device is not, and may not be,
offered for sale or lease, or sold, or leased until authorization from
the United States FCC or its equivalent in other countries has been
obtained. Use of this equipment in a residential location is
prohibited. This equipment generates, uses and can radiate radio
frequency energy which may result in harmful interference to radio
communications. If this equipment does cause harmful
interference to radio or television reception, which can be

IR Bullet Camera·User Manual
8
8
determined by turning the equipment on and off, the user is
required to take measures to eliminate the interference or
discontinue the use of this equipment.
Lead Content:
Please recycle this device in a responsible
manner. Refer to local environmental
regulations for proper recycling; do not dispose
of device in unsorted municipal waste.

IR Bullet Camera·User Manual
9
9
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the
warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
Please adopt the power adapter which can meet the safety
extra low voltage (SELV) request. And source with DC 12V or
AC 24V (depending on models) according to the IEC60950-1
and Limited Power Source standard.
If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

IR Bullet Camera·User Manual
10
10
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)
To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture.
This installation should be made by a qualified service person
and should conform to all local codes.
Please install blackouts equipment into the power supply
circuit for convenient supply interruption.
Please make sure that the ceiling can support more than 50(N)
Newton gravities if the camera is fixed to the ceiling.
Cautions
Make sure the power supply voltage is correct before using the
camera.
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules w ith fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period of
time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera at the sun or extra bright places. A
blooming or smear may occur otherwise (which is not a
malfunction however), and affecting the endurance of sensor
at the same time.

IR Bullet Camera·User Manual
11
11
The sensor may be burned out by a laser beam, so when any
laser equipment is being used, make sure that the surface of
the sensor will not be exposed to the laser beam.
Do not place the camera in extremely hot or cold temperatures
(the operating temperature should be between -10°C ~ 60°C ,
dusty or damp locations, and do not expose it to high
electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for a
proper operating environment.
Do not let water and any liquid flow into the camera.
While shipping, the camera should be packed in its original
packing, or packing of the same texture.
Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.

IR Bullet Camera·User Manual
12
12
Table of Contents
1 Introduction ......................................................................13
1.1 Product Features .................................................... 13
1.2 Overview ............................................................... 14
2 Installation........................................................................17
2.1 Installation of Camera A......................................... 17
2.2 Installation of Camera B......................................... 20
2.3 Installation of Camera C......................................... 22
2.4 Wiring .................................................................... 24
Appendix...............................................................................27
1 Glossary ................................................................... 27
2 Troubleshooting......................................................... 31
3 Technical Maintenance............................................... 33

IR Bullet Camera·User Manual
13
13
1Introduction
1.1 Product Features
This camera adopts high performance sensor and advanced print
circuit board design techno logy. It possesses of high resolution,
low distortion, and low noise features, etc. It is extremely suitable
for surveillance system and image process system.
Supply high definition and clear image
Integrate infrared lights to allow the camera to be used both in
the day and the night
Day Night Auto Switch
Support auto white balance with high color rendition
Back Light Compensation
Support 3D digital noise reduction
Support SMART IR function
Note: Only the DS-2CC1172P(N)-IR1T(IR3T)(IR5T) and
DS-2CC1182P(N)-IR1T(IR3T)(IR5T) models support the 3D digital
noise reduction and SMART IR functions.
Support auto electronic shutter control to adapt to different
environments
Support auto gain control, adaptive brightness
High SNR lead to clear and pleased image

IR Bullet Camera·User Manual
14
14
Advanced engineering design, high Reliability
Ingress Protection: IP66
1.2 Overview
The appearances of the cameras are as follows:
Camera A:
1
2
Figure 1-1 Overview of
DS-2CC102/112/192/1182/1192/11A2P(N)-IR1(IR3)(IR5) and
1172/1182P(N)-IR1T(IR3T)(IR5T)
1 Sun Shield
2 Lock Screw

IR Bullet Camera·User Manual
15
15
Camera B:
1
2
Figure 1-2 Overview of
DS-2CC102/112/192/1182/1192/11A2P(N)-IRA
1 Sun Shield
2 Lock Screw

IR Bullet Camera·User Manual
16
16
Camera C:
1
2
4
3
Figure 1-3 Overview of DS-2CC102/112/192/1132P(N)-IR
1 Power Supply Interface
2 Video Interface
3 Mounting Base
4 Bracket

IR Bullet Camera·User Manual
17
17
2Installation
Before you start:
Please make sure that the device in the package is in good
condition and all the assembly parts are included.
Notes:
IR bullet camera is usually used for outdoor or indoor with low
illumination environment. It is usually installed on the wall, so
please refer to the following steps of wall mounting to install
the camera.
Please ensure that the wall is strong enough to withstand more
than 3 times the weight of the camera and the bracket. If the
wall is not strong enough, the camera may fall and cause
serious damage.
For the cement wall, you need to mount the camera with
expansion screws. For the woodiness wall, you can mount the
camera with self-tapping screws.
2.1 Installation of Camera A
Notes:
The models of camera A are
DS-2CC102/112/192/1182/1192/11A2P(N)-IR1(IR3)(IR5)
and 1172/1182P(N)-IR1T(IR3T)(IR5T).
The mount must be longer than 1/2 the length of camera.

IR Bullet Camera·User Manual
18
18
Steps:
1. Attach the wall mount to the wall, and use screws to fix it as
shown in Figure 2-1.
Figure 2-1 Fix the Wall Mount
2. Attach the camera mounting base to the wall mount.
3. Secure the camera to the wall mount with screws as shown in
Figure 2-2.

IR Bullet Camera·User Manual
19
19
Figure 2-2 Fix the Camera
4. Loosen the panning screw and tilting screw of the mount as
shown in Figure 2-3.
5. Adjust the camera to the desired monitoring angle.
6. Tighten the panning and tilting screws.
Figure 2-3 Adjust the Monitoring Angle
Panning Screw
Tilting Screw