HIK VISION E-series User manual

E Series IR Speed Dome
Installation Manual
UD.6L0201A1075A01

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
1
Thank you for purchasing our product. If there are any questions, or requests, please do not
hesitate to contact the dealer.
This manual applies to E Series IR Speed Dome.
This manual may contain several technical or printing errors, and the content is subject to change
without notice. The updates will be added to the new version of this manual. We will readily
improve or update the products or procedures described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security
or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined
in UL’s Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or
reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
0100001030607

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info.

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
3
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid
danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings Follow these safeguards to
prevent serious injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety regulations,
fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal company. The standard of the
power adapter is 24VAC10% or 12VDC10% (depending on models). The power consumption
cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle
the speed dome.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility
for problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places
subject to shock (ignorance can cause equipment damage).
Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire or
electrical shock will occur. The operating temperature should be -30°C ~ 65°C .
The dome cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
4
radiator is forbidden (ignorance can cause fire danger).
Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfunction however), and affecting the endurance of sensor at the
same time.
Please use the provided glove when open up the dome cover, avoid direct contact with the
dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome
cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, do
not use alkaline detergents.
Do not stare at infrared LED closely to avoid hurting your eyes when the infrared lights are on.
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you
need to return the speed dome to the factory with the original wrapper. Transportation without
the original wrapper may result in damage on the speed dome and lead to additional costs.

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
5
Table of Contents
Chapter 1 Installation............................................................................................................................................ 6
1.1 Installing the IR Speed Dome ......................................................................................................................... 6
1.2 Connecting the Cables................................................................................................................................... 8
1.3 DIP Switch Settings........................................................................................................................................ 9
1.3.1 Address Settings........................................................................................................................................ 9
1.3.2 Baudrate Settings .....................................................................................................................................12
1.3.3 Protocol Settings ......................................................................................................................................12
1.3.4 Communication Mode Settings.................................................................................................................12
1.3.5 Terminal Resistor Settings.........................................................................................................................13
1.4 Power Cable Requirement ............................................................................................................................13
Chapter 2 Mount Dimension................................................................................................................................14
2.1 Wall Mount..................................................................................................................................................14
2.2 Corner Adapter ............................................................................................................................................15
2.3 Pole Adapter ................................................................................................................................................16
2.4 Pendant Mount............................................................................................................................................17
Chapter 3 Mounting Applications ........................................................................................................................18
3.1 Wall Mounting Applications..........................................................................................................................18
3.1.1 Components.............................................................................................................................................18
3.1.2 Wall Mounting .........................................................................................................................................19
3.2 Corner Mounting Applications......................................................................................................................20
3.1.1 Components.............................................................................................................................................20
3.1.2 Corner Mounting......................................................................................................................................21
3.3 Pole Mounting Applications..........................................................................................................................22
3.1.3 Components.............................................................................................................................................22
3.1.4 Pole Mounting..........................................................................................................................................24
3.4 Pendant Mounting Applications....................................................................................................................26
3.1.5 Components.............................................................................................................................................26
3.1.6 Pendant Mounting ...................................................................................................................................26
Appendix.....................................................................................................................................................................29
Appendix 1 Lightning & Surge Protection..................................................................................................................29
Appendix 2 Waterproof ............................................................................................................................................33
Appendix 3 Bubble Maintenance..............................................................................................................................35
Appendix 4 RS485 Bus Connection............................................................................................................................36
Appendix 5 24VAC Wire Gauge & Transmission Distance...........................................................................................39
Appendix 6 Wire Gauge Standards ...........................................................................................................................40

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
6
Chapter 1 Installation
Before you start:
Check the package contents and make sure that the device in the package is in good condition and
all the assembly parts are included.
Note: Do not drag the waterproof cables as shown in Figure 1-1, otherwise the waterproof
performance is affected.
Figure 1-1 Do not Drag the Cables
1.1 Installing the IR Speed Dome
Before you start:
Check the package contents and make sure that the device in the package is in good condition
and all the assembly parts are included.
Please make sure the wall is strong enough to withstand more than 8 times the weight of the
dome and the mount.
For cement wall, you need to use the expansion screw to fix the mount.
The long-arm wall mount is taken as the example for following mounting steps.
Steps:
1. Remove the protective sticker from the dome drive.

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
7
Figure 1-2 Protective Sticker
2. Drill 4 screw holes in the wall according to the holes of the mount.
3. Fix the wall mount to the wall with the M8 expansion screws.
Figure 1-3 Fix the Mount
4. Install the speed dome to the mount.
1). Hang the safety rope to the speed dome and then hook to the mount as shown in Figure 1-4.
2). Route the cables of the speed dome through the wall mount.
3). Loosen the two lock screws on the wall mount.
4). Install the speed dome to the mount, and secure the speed dome by rotating the speed dome
clockwise.
5). Fasten the two lock screws with the Allen wrench.
Figure 1-4 Secure the Speed Dome
Protective
Sticker
Safety Rope
Lock Screw

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
8
1.2 Connecting the Cables
Before you start:
Please make sure the power of the dome is off before connecting the cables.
Cable Connection of Analog Speed Dome:
Choose the video cable according to the transmission length. The video should meet the least
demands as: 75Ω resistance; 100% copper core conducting wire; 95% weaving copper shield.
RS485 communication cable, please refer to Appendix 4
The cable interfaces of speed dome are shown in the following figures. Please refer to the following
figure for connecting the RS-485, power and video cables.
As shown in the following figures, the label instructs you to connect the power cables. The label
and instruct you to connect the RS-485 cables.
ORANGE RS485+
YELLOW RS485-
Lable 1
Lable 2
Lable 1
Lable 2
Black
Yellow Green
Red
Yellow
Orange
RED AC24V
YELLOW/GREEN
BLACK AC24V
Figure 1-5 Cables of Analog IR Speed Dome
Cable Connection of Network Speed Dome:
Figure 1-6 Cables of Network IR Speed Dome
24VAC Black
GND Yellow-green
24VAC Red
Network Cable

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
9
1.3 DIP Switch Settings
Note: This section is only for analog speed domes.
Two DIP switches SW1 and SW2 are for setting the speed dome address, baudrate, protocol, etc.,
with value ON=1 and OFF=0. The switch label is on the back of the SWITCH cover as shown in Figure
1-7.
Each number of the switch represents a DIP value, ranging from 1 to 8 for the lowest to highest.
Please refer to Section 1.3.1 to 1.3.5 for detailed settings.
SW1 SW2
SWITCH
Figure 1-7 Label of DIP Switch
Note: The default dome address is 0; the default baudrate is 2400; and the default value of the
120Ωterminator is OFF.
1.3.1 Address Settings
The SW1 switch is used for setting the address of speed dome. You can refer to Table 1-1 and Table
1-2 for details of setting the speed dome address to a specific number.
Table 1-1 Set the Dome Address
Dome
Address
SW1 Settings
1
2
3
4
5
6
7
8
0
ON
1 2 3 4 5 6 7 8
SW1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
1 2 3 4 5 6 7 8
SW1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DIP Switch Label

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
10
Dome
Address
SW1 Settings
1
2
3
4
5
6
7
8
-
-
-
-
-
-
-
-
-
-
255
ON
1 2 3 4 5 6 7 8
SW1
ON
ON
ON
ON
ON
ON
ON
ON
Refer to the following table for more address settings:
Table 1-2 Set the Dome Address from 0 to 71
DIP Switch SW1 Settings
Address
1
2
3
4
5
6
7
8
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
9
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
10
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
11
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
12
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
13
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
14
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
15
ON
ON
ON
ON
OFF
OFF
OFF
OFF
16
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
17
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
18
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
19
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
20
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
21
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
22
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
23
ON
ON
ON
OFF
ON
OFF
OFF
OFF
24
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
25
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
26
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
27
ON
ON
OFF
ON
ON
OFF
OFF
OFF
28
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
29
ON
OFF
ON
ON
ON
OFF
OFF
OFF
30
OFF
ON
ON
ON
ON
OFF
OFF
OFF
31
ON
ON
ON
ON
ON
OFF
OFF
OFF

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
11
DIP Switch SW1 Settings
32
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
33
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
34
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
35
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
36
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
37
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
38
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
39
ON
ON
ON
OFF
OFF
ON
OFF
OFF
40
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
41
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
42
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
43
ON
ON
OFF
ON
OFF
ON
OFF
OFF
44
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
45
ON
OFF
ON
ON
OFF
ON
OFF
OFF
46
OFF
ON
ON
ON
OFF
ON
OFF
OFF
47
ON
ON
ON
ON
OFF
ON
OFF
OFF
48
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
49
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
50
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
51
ON
ON
OFF
OFF
ON
ON
OFF
OFF
52
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
53
ON
OFF
ON
OFF
ON
ON
OFF
OFF
54
OFF
ON
ON
OFF
ON
ON
OFF
OFF
55
ON
ON
ON
OFF
ON
ON
OFF
OFF
56
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
57
ON
OFF
OFF
ON
ON
ON
OFF
OFF
58
OFF
ON
OFF
ON
ON
ON
OFF
OFF
59
ON
ON
OFF
ON
ON
ON
OFF
OFF
60
OFF
OFF
ON
ON
ON
ON
OFF
OFF
61
ON
OFF
ON
ON
ON
ON
OFF
OFF
62
OFF
ON
ON
ON
ON
ON
OFF
OFF
63
ON
ON
ON
ON
ON
ON
OFF
OFF
64
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
65
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
66
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
67
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
68
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
69
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
70
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
71
ON
ON
ON
OFF
OFF
OFF
ON
OFF

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
12
1.3.2 Baudrate Settings
The No. 1, 2 and 3 of SW2 switch are for setting the baudrate of the speed dome, standing for
2400bps, 4800bps and 9600bps respectively. The baudrate will be set as 2400bps by default if it is
out of this range. Refer to the following table:
Table 1-3 Set the Baudrate of the Dome
DIP Switch SW2-Baudrate Settings
Baudrate
Figure
1
2
3
2400
ON
1 2 3 4 5 6 7 8
SW2
ON
OFF
OFF
4800
ON
1 2 3 4 5 6 7 8
SW2
OFF
ON
OFF
9600
ON
1 2 3 4 5 6 7 8
SW2
ON
ON
OFF
1.3.3 Protocol Settings
The No. 4, 5 and 6 of SW2 switch are for setting the communication protocols of the dome. Refer to
the following table:
Table 1-4 Set the Protocol of the Dome
DIP Switch SW2-Protocol Settings
Protocol
Figure
4
5
6
AD Manchester
O
N
12345678
SW
2
ON
ON
ON
Others
Self-adaptive
Notes:
The speed dome is self-adaptive to PELCO-D, PELCO-P and private protocol which cannot set by
the DIP switches.
Network speed dome model does not support Manchester Code protocol.
1.3.4 Communication Mode Settings
The No. 7 of SW2 switch is for setting the RS485 communication mode of the dome to simplex or
half-duplex.
Table 1-5 Set Communication Mode of the Dome
DIP Switch SW2-Simplex/Half-duplex
Settings
Description
Figure
7
Simplex
ON
1 2 3 4 5 6 7 8
SW2
OFF
Half-duplex
ON
1 2 3 4 5 6 78
SW2
ON

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
13
1.3.5 Terminal Resistor Settings
The No. 8 of SW2 switch is used for turning on/off the 120Ωterminal resistor.
Table 1-6 Set Terminal Resistor
Switch Number
Description
8
Turn on the resistor
OFF
Turn off the resistor
ON
1.4 Power Cable Requirement
When the speed dome uses standard AC power supply, the power cable should meet the demand.
The formula of the cross-section S (mm²) and the maximum transmission distance L (m) of the bare
wire is as follows:
L=50*S (analog speed dome)
L=40*S (network speed dome)
Example:
For the analog speed dome, the cross-section of the cable is 1mm²and the transmission distance is
less than 50m.
According to the Appendix 5 24VAC Wire Gauge Standards, for example, the American wire gauge
18, the transmission distance should be 0.7854*50=39.27m.

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
14
Chapter 2 Mount Dimension
Note: Not all of the mounts are listed in this manual. Please refer to the specification manual.
2.1 Wall Mount
You can use the wall mount with corner adapter or pole adapter according to different installation
environments.
181.9
97 305
75
160
φ8.5
Figure 2-1 Wall Mount

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
15
2.2 Corner Adapter
A corner adapter has to be used together with a wall mount for corner mounting applications.
Figure 2-2 Corner Adapter

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
16
2.3 Pole Adapter
A pole adapter has to be used together with a wall mount for pole mounting applications.
Figure 2-3 Pole Adapter

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
17
2.4 Pendant Mount
Figure 2-4 Pendant Mount

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
18
Chapter 3 Mounting Applications
Before you start:
For cement wall, you need to use the expansion screw to fix the mount. The mounting hole of
the expansion pipe on the wall should align with the mounting hole on the mount.
For wooden wall, you can just use the self-tapping screw to fix the mount.
The wall must be thick enough to install the expansion screws.
Please make sure that the wall is strong enough to withstand more than 8 times the weight of
the dome and the mount.
3.1 Wall Mounting Applications
3.1.1 Components
Wall Mount
Figure 3-1 Wall Mount
Mounting Accessories
Figure 3-2 Nuts and Flat Washers

E Series IR Speed Dome Installation Manual
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
19
3.1.2 Wall Mounting
Steps:
1. Drill 4 screw holes in the wall according to the holes of the mount, and then insert M6
expansion screws (not supplied) into the mounting holes.
2. Attach the gasket then wall mount to the wall by aligning the 4 screw holes of the mount with
expansion screws on the wall.
3. Secure the wall mount with 4 hex nuts and washers.
Figure 3-3 Drill Screw Holes
4. Install the speed dome to the mount. Please refer to Section 1.1 Installing the IR Speed Dome
for installation details.
Figure 3-4 Finish the Installation