HIK VISION ECI-D64Z2 User manual

Network Dome Camera
ECI-D64Z2
Quick Start Guide

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 1
Manual Illustrations and Features
Gra hics (screen shots, roduct ictures, etc.) in this document are for illustrative ur oses
only. Your actual roduct may differ in a earance. Your roduct might not su ort all
features discussed in this document.
Hikvision USA Inc., 18639 Railroad St., City of Industry, CA 91748, USA • Hikvision Canada,
4848 rue Levy, Saint Laurent, Quebec, Canada, H4R 2P1
Tele hone: [phone] • Toll Free in USA: [phone] • E-Mail:
[email protected] • www.hikvision.com
COPYRIGHT ©2017-2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, ictures, gra hs are the
ro erties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter
referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”)
cannot be re roduced, changed, translated, or distributed, artially or wholly, by any
means, without the rior written ermission of Hikvision. Unless otherwise sti ulated,
Hikvision does not make any warranties, guarantees or re resentations, ex ress or im lied,
regarding to the Manual.
About t is Manual
The Manual includes instructions for using and managing the roduct. Pictures, charts,
images and all other information hereinafter are for descri tion and ex lanation only. The
information contained in the Manual is subject to change, without notice, due to firmware
u dates or other reasons. Please find the latest version in the com any Web site
(htt ://overseas.hikvision.com/en/).
Please use this user manual under the guidance of rofessionals.
Trademarks Acknowledgement
and other Hikvision trademarks and logos are the ro erties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the ro erties of their
res ective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED,
WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS,” WITH ALL FAULTS
AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY
SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG
OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 2
CONFORMS TO THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT
THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not ex ressly a roved by the arty
res onsible for com liance could void the user’s authority to o erate the equi ment.
FCC Compliance: This equi ment has been tested and found to com ly with the limits for a
Class B digital device, ursuant to art 15 of the FCC Rules. These limits are designed to
rovide reasonable rotection against harmful interference in a residential installation. This
equi ment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
articular installation. If this equi ment does cause harmful interference to radio or
television rece tion, which can be determined by turning the equi ment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the se aration between the equi ment and receiver.
•Connect the equi ment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an ex erienced radio/TV technician for hel
FCC Conditions
This device com lies with art 15 of the FCC Rules. O eration is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must acce t any interference received, including interference that may
cause undesired o eration.
EU Conformity Statement
This roduct and, if a licable, the su lied accessories too are marked with
“CE” and com ly therefore with the a licable harmonized Euro ean
standards listed under the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
dis osed of as unsorted munici al waste in the Euro ean Union. For ro er
recycling, return this roduct to your local su lier u on the urchase of
equivalent new equi ment, or dis ose of it at designated collection oints. For
more information see: www.recyclethis.info
2006/66/EC (battery directive): This roduct contains a battery that cannot be
dis osed of as unsorted munici al waste in the Euro ean Union. See the
roduct documentation for s ecific battery information. The battery is marked
with this symbol, which may include lettering to indicate cadmium (Cd), lead
(Pb), or mercury (Hg). For ro er recycling, return the battery to your su lier
or to a designated collection oint. For more information see: www.recyclethis.info

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 3
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
Safety Instruction
These instructions are intended to ensure that user can use the roduct correctly to avoid
danger or ro erty loss.
The recaution measure is divided into “Warnings” and “Cautions.”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equi ment damage may occur if any of the cautions are neglected.
Warnings
•Pro er configuration of all asswords and other security settings is the res onsibility of
the installer and/or end-user.
•In the use of the roduct, you must be in strict com liance with the electrical safety
regulations of the nation and region. Please refer to technical s ecifications for detailed
information.
•In ut voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited
Power Source with 12 VDC according to the IEC60950-1 standard. Please refer to
technical s ecifications for detailed information.
•Do not connect several devices to one ower ada ter as ada ter overload may cause
over-heating or a fire hazard.
•Please make sure that the lug is firmly connected to the ower socket. When the
roduct is mounted on wall or ceiling, the device shall be firmly fixed.
•If smoke, odor or noise rise from the device, turn off the ower at once and un lug the
ower cable, and then lease contact the service center.
Cautions
•Make sure the ower su ly voltage is correct before using the camera.
•Do not dro the camera or subject it to hysical shock.
•Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a
bit of ethanol and wi e it gently. If the camera will not be used for an extended eriod,
lease re lace the lens ca to rotect the sensor from dirt.
•Do not aim the camera at the sun or extra bright locations. Blooming or smearing may
occur (which is not a malfunction), and affect the sensor endurance at the same time.
Warnings Follow these safeguards to
revent serious injury or death.
Cautions Follow these recautions to
revent otential injury or material
damage.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 4
•The sensor may be burned out by a laser beam, so when any laser equi ment is in using,
make sure that the surface of sensor will not be ex osed to the laser beam.
•Do not lace the camera in extremely hot, cold (the o erating tem erature shall be -30°
to +60° C, or -40° to +60° C if the camera model has an “H” in its suffix), dusty or dam
locations, and do not ex ose it to high electromagnetic radiation.
•To avoid heat accumulation, good ventilation is required for the o erating environment.
•Kee the camera away from liquid while in use.
•While in delivery, the camera shall be acked in its original acking or acking of the
same texture.
•Regular art re lacement: a few arts (e.g., electrolytic ca acitor) of the equi ment shall
be re laced regularly according to their average enduring time. The average time varies
because of differences between o erating environment and using history, so regular
checking is recommended for all the users. Please contact with your dealer for more
details.
•Im ro er use or re lacement of the battery may result in hazard of ex losion. Re lace
with the same or equivalent ty e only. Dis ose of used batteries according to the
instructions rovided by the battery manufacturer.
•If the roduct does not work ro erly, lease contact your dealer or the nearest service
center. Never attem t to disassemble the camera yourself. (We shall not assume any
res onsibility for roblems caused by unauthorized re air or maintenance.)

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 5
Table of Contents
1 Appearance ...................................................................................................................... 6
Camera Overview ...................................................................................................... 6 1.1
1.1.1 Overview .......................................................................................................... 6
2 Installation ........................................................................................................................ 6
Pre aration ................................................................................................................ 7 2.1
2.1.1 Disassembly ...................................................................................................... 7
2.1.2 Memory Card Installation ................................................................................. 7
Mounting ................................................................................................................... 8 2.2
2.2.1 Ceiling Mount ................................................................................................... 8
2.2.2 Conduit Installation .......................................................................................... 9
Image and Focus Adjustment .................................................................................. 10 2.3
2.3.1 3-Axis Adjustment .......................................................................................... 11
2.3.2 Zoom and Focus Adjustment .......................................................................... 11
3 Camera LAN Configuration .............................................................................................. 12
Wiring ...................................................................................................................... 12 3.1
Activate the Camera ................................................................................................ 13 3.2
3.2.1 Activation via Web Browser ............................................................................ 13
3.2.2 Activation via SADP Software ......................................................................... 14
Modify the IP Address.............................................................................................. 15 3.3
4 Access via Web Browser .................................................................................................. 16
5 Hik-Connect .................................................................................................................... 17
Enable Hik-Connect for Use with Cameras .............................................................. 17 5.1
Enable Hik-Connect Service via SADP Software ....................................................... 17 5.2
5.2.1 Enable Hik-Connect via a Web Browser .......................................................... 18
Add Camera to Hik-Connect .................................................................................... 18 5.3
Initialize the Memory Card ...................................................................................... 19 5.4

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 6
1Appearance
This camera series consists of several different models. Some models are equi ed with a
zoom lens, in which focus levels must be manually adjusted via a zoom/focus lever. Other
models have a motor-driven lens, which allow for zoom and focus adjustment to be
com leted via web browser or client software. Please refer to the actual device.
Camera Overview 1.1
1.1.1 Overview
Camera overview is shown below.
DC12VIN
5
6
1
7
2
3
4
Figure 1-1 Camera Overview
Table 1-1 Camera Overview
No
.
Description
1 Black Liner
2 Bubble
3 Reset Button
4 Memory Card Slot
5 Power Cord
6 Network Cable (PoE)
7 Lens
Notes:
Press RESET for 10s when the camera is owering u or rebooting, in order to restore the
default settings, which include the user name, assword, IP address, ort number, etc.
2Installation
Make sure of t e following before starting:
● The device included in the ackage is in good condition and all required arts are
included.
● The standard ower su ly is 12 VDC or PoE (802.3af), and must be consistent with
camera requirements.
● Equi ment is owered off during installation.
● The installation environment is correct.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 7
● The wall is strong enough to withstand four times the weight of the camera and mount.
For IR cameras, take the following recautions in order to revent IR reflection:
● Dust or grease on the dome cover will cause IR reflection. Please do not remove the
dome cover film until installation is com lete. If there is dust or grease on the dome
cover, clean the dome cover with a soft cloth and iso ro yl alcohol.
● Make sure that there is no reflective surface that is too close to the camera lens. The IR
light from the camera may reflect back into the lens, which may cause reflection.
● The foam ring around the lens must be seated flush against the inner surface of the
bubble, so as to isolate the lens from the IR LEDS. Fasten the dome cover to the camera
body, and ensure that the foam ring and dome cover are seamlessly attached.
Preparation 2.1
Before mounting, disassemble the camera and install the memory card.
2.1.1 Disassembly
Steps:
1. Loosen the three screws on the edge of the bubble with a screw driver.
2. Take off the bubble.
3. Remove the inner black liner.
Black Liner
Screws
Bubble
Remove the Bubble and Black Liner Figure 2-1
2.1.2 Memory Card Installation
Steps:
1. Rotate the camera body to com letely ex ose the memory card slot.
2. Insert the memory card and ush to mount.
Note:
A microSD memory card is not included with the camera and must be urchased se arately.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 8
Memory Card
Install the Memory Card Figure 2-2
3. (O tional) Unmount the memory card by ejecting it.
Mounting 2.2
2.2.1 Ceiling Mount
Steps:
1. Fix the su lied drill tem late to the area where you would like to install the camera.
2. Drill three screw holes and a cable hole (o tional) into the ceiling according to the drill
tem late.
58 mm (2.28" )
43.3 mm (1 .7" )
29 mm
(1.14")
50 mm
(1.97" )
25 mm
(0.98" )
50.3 mm (1.98" )
The Drill Tem late Figure 2-3
Note:
If you need to route cables through the ceiling, drill a cable hole according to the drill
tem late. Ski this ste if you want to route the cables along the ceiling surface.
3. Route the camera cables.
4. Align the holes of the back box with the drilled screw holes on the ceiling, and secure
the camera with the su lied screws.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 9
Back Box
Secure the Camera Figure 2-4
Note:
● The su lied screw ackage contains self-ta ing screws and ex ansion bolts.
● For cement ceilings, secure the camera with ex ansion bolts. For wooden ceilings, use
self-ta ing screws.
5. Connect corres onding cables, such as the ower cord and network cable.
6. Power the camera on, and set the network configuration (for details, refer to 3 Camera
LAN Configuration and 4 Access via Web Browser) to check whether the image was
shot from the right angle. If not, adjust the surveillance angle (for details, refer to
section 2.3.1 3 Axis Adjustment).
7. Re lace the inner black liner.
8. Install the bubble back onto the camera and re lace the screws.
Secure Black Liner and Bubble Figure 2-5
2.2.2 Conduit Installation
To route the cables from side of the camera, install a cable routing conduit.
Steps:
1. Rotate the water roof lug counterclockwise and remove it.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 10
Side Outlet
Water roof
Plug
Remove the Water roof Plug Figure 2-6
2. Route the cables through the side outlet towards the conduit.
3. Insert the conduit into the outlet and tighten counterclockwise.
Conduit
Install the Cable Conduit Figure 2-7
Note:
When mounting on a wall, osition the side outlet downwards to revent the collection of
water.
Downward
Conduit Outlet Direction Figure 2-8
Image and Focus Adjustment 2.3
Before you start:
Connect the camera to a monitor with the su lied auxiliary video out ut cable, and ower
the camera on.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 11
Auxiliary Video
Cable
Auxiliary Video
Out ut
To a monitor
Connect Camera to a Monitor Figure 2-9
Note:
For certain camera models, the auxiliary video cable is not included in the ackage. Instead,
you can connect the video out interface of the camera to a monitor for image and focus
adjustment.
Video Out
Interface
Camera Video-Out Interface Figure 2-10
2.3.1 3-Axis Adjustment
Steps:
1. View camera out ut on the monitor.
2. Loosen the tilt adjusting screw to adjust the tilt angle [0° to 70°], hold the black liner to
adjust the an angle [0° to 355°], and hold the lens to rotate the camera [0° to 355°].
Tilt: 0° to 70°
Pan: 0° to 355°
Rotate: 0° to 355°
3-Axis Adjustment Figure 2-11
2.3.2 Zoom and Focus Adjustment
Manual Adjustment:
Some camera models in this series have a zoom lens. Focus levels must be manually
adjusted via the zoom/focus lever. Use the zoom and focus levers to adjust the lens.
Steps:
1. View camera out ut on the monitor.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 12
2. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the
ideal viewing angle.
Zoom/Focus Lever
Zoom/Focus Lever (Ty e II Camera) Figure 2-12
3. Tighten the zoom lever.
4. Loosen the focus lever and move the lever between F (Far) and N (Near) to obtain the
o timum focus.
5. Tighten the focus lever.
Motor-Driven Lens:
Some camera models in this series are equi ed with a motor-driven lens. Adjust the zoom
and focus level in the PTZ control anel found in the Web browser or client software.
Web Browser Zoom and Focus Adjustment
3Camera LAN Configuration
Note:
The use of roducts with internet access carries inherent security risks. In order to avoid
network attacks and information leakage, strengthen your own network rotection.
If the roduct does not work ro erly, contact your dealer or the nearest service center for
hel .
Wiring 3.1
Connect the camera to network as follows:
Network Cable
or
Network Camera
Computer
Connect Directly Figure 3-1

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 13
Network Cable
Network Cable
or
or
Network Camera Computer
Connect via a Switch or a Router Figure 3-2
Activate t e Camera 3.2
Activate the camera by setting a strong assword. Activation via web browser, activation via
SADP, and activation via client software are su orted. Activation via SADP software and
web browser will be used as exam les to introduce camera activation.
Note:
Refer to the Network Camera User Manual for activation via client software.
3.2.1 Activation via Web Browser
Steps:
1. Power the camera on. Connect the camera to your com uter or the switch/router that
your com uter connects to.
2. In ut the IP address into the address bar of the web browser, and ress Enter to enter
the activation interface.
Notes:
 The camera’s default IP address is 192.168.1.64.
 The com uter and the camera should belong to the same subnet.
 For cameras that have DHCP enabled by default, use the SADP software to search for the
IP address.
Activation Interface (Web) Figure 3-3
3. Create and in ut a assword.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 14
STRONG PASSWORD RECOMMENDED – We highly recommend creating a strong
password of your own choosing (using a minimum of eight characters, including
upper case letters, lower case letters, numbers, and special characters) in order to
increase the security of your product. We recommend regularly resetting your
password on a weekly or monthly basis, especially in high security systems.
4. Confirm the assword.
5. Click OK to save the assword and enter the live view interface.
3.2.2 Activation via SADP Software
SADP software is used for detecting online devices, activating cameras, and resetting
asswords.
SADP can be obtained from the su lied disk or the official website, and installed by
following the rom ts.
Follow the ste s to activate the camera.
Steps:
1. Run SADP to search for online devices.
2. Check the device status from the device list, and select the inactive device.
Select inactive device.
In ut and confirm
assword.
SADP Interface Figure 3-4
Note:
SADP su orts batch camera activations. Refer to the SADP user manual for further details.
3. Create, in ut, and confirm the assword.
STRONG PASSWORD RECOMMENDED – We highly recommend creating a strong
password of your own choosing (using a minimum of eight characters, including
upper case letters, lower case letters, numbers, and special characters) in order to
increase the security of your product. We recommend regularly resetting your
password on a weekly or monthly basis, especially in high security systems.
Note:
You can enable the Hik-Connect service for the device during activation. Refer to Cha ter
5.1 for detailed information.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 15
4. Click Activate to start activation.
You can check whether the activation is com lete in the o u window. If activation failed,
make sure that the assword meets the requirements, and try again.
Modify t e IP Address 3.3
Purpose:
To view and configure the camera via LAN (Local Area Network), you need to connect the
network camera in the same subnet as your PC.
Use the SADP software or client software to search and change the IP address of the device.
IP Address modification via SADP software will be used as an exam le.
In order to modify the IP address via client software, refer to the user manual of the client
software.
Steps:
1. Run SADP.
2. Select an active device.
3. Change the device IP address to the same subnet as your com uter by either modifying
the IP address manually, or by checking the Enable DHCP checkbox.
Modify the IP Address Figure 3-5
Note:
Hik-Connect can be enabled during activation. Refer to Cha ter 5.1 for detailed information.
4. In ut the admin assword and click Modify to com lete IP address modification.
SADP su orts batch IP address modification. Refer to the SADP user manual for details.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 16
4Access via Web Browser
System Requirement:
O erating System: Microsoft Windows XP SP1 and above
CPU: 2.0 GHz or greater
RAM: 1 Gb or greater
Dis lay: 1024×768 resolution or higher
Web Browser: Internet Ex lorer 8.0 or higher, A le Safari 5.0.2 or higher, Mozilla Firefox
5.0 or higher, and Google Chrome 18 or higher
Steps:
1. O en the Web browser.
2. In the browser address bar, in ut the IP address of the network camera, and ress the
Enter key to enter the login interface.
Note:
The default IP address is 192.168.1.64. It is suggested that you change the IP address to the
same subnet as your com uter.
3. In ut the user name and assword.
The admin user should configure the device accounts and user/o erator ermissions
ro erly. Delete the unnecessary accounts and user/o erator ermissions.
Note:
The device IP address gets locked if the admin user erforms seven failed assword
attem ts (five attem ts for the user/o erator).
4. Click Login.
Login Interface Figure 4-1
5. Install the lug-in before viewing the live video and managing the camera. Follow the
installation rom ts to install the lug-in.
Note:
You may have to close the Web browser to com lete lug-in installation.
Download Plug-in Figure 4-2

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 17
6. Reo en the Web browser after lug-in installation and re eat ste s 2 to 4 in order to
login.
Note:
For further configuration instructions, lease refer to the network camera user manual.
5 Hik-Connect
Purpose:
Hik-Connect is a mobile a lication to view live camera images, receive alarm notifications,
etc.
Enable Hik-Connect for Use wit Cameras 5.1
Purpose:
Enable Hik-Connect should on your camera before using the service.
You can enable the service either via SADP software or a Web browser.
Enable Hik-Connect Service via SADP Software 5.2
Steps:
1. Check the Enable Hik-Connect checkbox:
1). For the “Activate the Device” age that a ears during camera activation, refer to
Cha ter 3.2.2.
2). For the “Modify Network Parameters” age that a ears while modifying the IP
address, refer to Cha ter 3.3.
2. Create or change the verification code.
Verification Code Setting (SADP) Figure 5-1
Note:
The verification code is required when adding the camera to Hik-Connect.
3. Click and read the “Terms of Service” and “Privacy Policy.”
4. Confirm the settings.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 18
5.2.1 Enable Hik-Connect via a Web Browser
Before You Start:
Activate the camera before enabling the service. Refer to Cha ter 3.2. for more information.
Steps:
5. Access the camera via the Web browser. Refer to Cha ter 4.
6. Enter the latform access configuration interface, as follows: Configuration > Network >
Advanced Settings > Platform Access.
Platform Access Configuration (Web) Figure 5-2
7. Set the Platform Access Mode to Hik-Connect.
8. Check the Enable checkbox.
9. Click and read the “Terms of Service” and “Privacy Policy” in the o -u window.
10. Create or change the verification code for the camera.
Note:
A verification code is required when you add the camera to Hik-Connect.
11. Save the settings.
Add Camera to Hik-Connect 5.3
Before You Start:
You need to enable Hik-Connect on the camera before adding it to your Hik-Connect
account. Refer to Cha ter 5.1.
Steps:
1. Use a network cable to connect the camera to a router if the camera does not su ort
Wi-Fi.

ECI-D64Z2 Network Dome Camera Quick Start Guide
QSG VE ECI-D64Z2 041118NA 19
Figure 5-3 Connect a Router
Note:
After the camera connects to the network, wait one minute before using the camera with
Hik-Connect.
2. Add the camera to the Hik-Connect a :
•If Accessing t e Camera t roug an NVR: Ta “+” on the u er-right corner and scan
the QR code that a ears in the NVR interface.
•If Accessing t e Camera t roug a Web Browser: Ta the icon and ty e in the
camera’s serial number.
3. In ut your camera’s verification code.
Note:
The required verification code is created or changed when you enable Hik-Connect on your
camera.
Forgotten verification codes can be recovered in the Platform Access configuration age via
the web browser.
4. Follow rom ts to set u the network connection and add the camera to your
Hik-Connect account.
Note:
For detailed information, refer to the Hik-Connect user manual.
Initialize t e Memory Card 5.4
Note:
A microSD memory card is not included with the camera and must be urchased se arately.
Steps:
1. Check the status of the memory card by ta ing on the Storage Status in the Device
Settings interface.
2. If the memory card status dis lays as Uninitialized, ta to initialize it. The status will
then change to Normal. You can then start recording any event-triggered video in the
camera such as motion detection-generated videos.