HIK VISION PanoVu PT Series User manual

PanoVu PT Series Target
Capture Camera
Quick Start Guide
COPYRIGHT © 2018 Hikvision. ALL RIGHTS RESERVED

Quick Start Guide
ALL RIGHTS RESERVED
Any and all information, including, among others, wordings, pictures,
graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
This user manual (hereinafter referred to be “the Manual”) cannot
be reproduced, changed, translated, or distributed, partially or whol-
ly, by any means, without the prior written permission of Hikvision.
Unless otherwise stipulated, Hikvision does not make any warran-
ties, guarantees or representations, express or implied, regarding to
the Manual.
About this Manual
This Manual is applicable to PanoVu PT Series Target Capture
Camera.
The Manual includes instructions for using and managing the prod-
uct. Pictures, charts, images and all other information hereinafter
are for description and explanation only. The information contained
in the Manual is subject to change, without notice, due to rmware
updates or other reasons. Please nd the latest version in the com-
pany website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are
the properties of Hikvision in various jurisdictions. Other trademarks
and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL
FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRAN-
TIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITA-
TION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS
FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF
THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS,
OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR

ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR
LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE
USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR AB-
NORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAM-
AGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,
VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL
SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE
CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE
USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR
USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL
NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED
WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL
AND THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly ap-
proved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC compliance:
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Op-
eration of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the inter-
ference at his own expense.
FCC conditions

This device complies with part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interfer-
ence that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories
too are marked with "CE" and comply therefore withthe
applicable harmonized European standards listed under
the the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated
collection points. For more information see: www.
recyclethis.info
2006/66/EC (battery directive): This product contains
a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product
documentation for specic battery information. The battery
is marked with this symbol, which may include lettering
to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier
or to a designated collection point. For more information
see:www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards require-
ments.

Safety Instruction
These instructions are intended to ensure that the user can
use the product correctly to avoid danger or property loss.
Laws and Regulations
The device should be used in compliance with local laws, electrical
safety regulations, and re prevention regulations.
Transportation
Keep the device in original or similar packaging while transporting it.
Power Supply
The input voltage should conform to IEC60950-1 standard: SELV
(Safety Extra Low Voltage) and the Limited Power Source. Refer to the
appropriate documentation for detailed information.
The standard power supply is 12 VDC or Hi-PoE, please make sure
your power supply matches with your camera.
DO NOT connect multiple devices to one power adapter, to avoid over-
heating or re hazards caused by overload.
Make sure the plug is properly connected to the power socket.
This is a class A product. In a domestic environment this product may
cause radio inter-ference in which case the user may be required to take
adequate measures.
System Security
The installer and user are responsible for password and security
conguration and its settings.
Battery
Improper use or replacement of the battery may result in explosion
hazard. Replace with the same or equivalent type only. Dispose of used
batteries in conformance with the local codes.
Maintenance
If the product does not work properly, please contact your dealer or
the nearest service center. We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require regular
replacement. The average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside surfaces
of the product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device lens is
not exposed to the laser beam, or it may burn out.
Do not expose the device to high electromagnetic radiation or dusty
environments.
Warnings
Serious injury or death may be caused if any of these warnings are
neglected.
Follow these safeguards to prevent serious injury or death.
Cautions
Cautions: Injury or equipment damage may be caused if any of
these cautions are neglected.
Follow these precautions to prevent potential injury or material
damage.
Warnings

Do not aim the lens at the sun or any other bright light.
Make sure the running environment meets the requirement of the
device.
Do not place the camera in extremely hot, cold, dusty or damp locations,
and do not expose it to high electromagnetic radiation.
IR Reection Prevention
Dust or grease on the dome cover will cause IR reflection. Please do
not remove the dome cover lm until the installation is nished. If there
is dust or grease on the dome cover, clean the dome cover with clean
soft cloth and isopropyl alcohol.
Make sure that there is no reflective surface too close to the camera
lens. The IR light from the camera may reect back into the lens causing
reection.
The foam ring around the lens must be seated ush against the inner
surface of the bubble to isolate the lens from the IR LEDS. Fasten the
dome cover to camera body so that the foam ring and the dome cover
are attached seamlessly.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the
power, unplug the power cable, and contact the service center.
Time Synchronization
Set up camera time manually for the rst time access if the local time
is not synchronized with that of the network. Visit the camera via Web
browse/client software and go to time settings interface.
Installation
Make sure the device is rmly secured to any wall or ceiling mountings.
We recommend you to adjust the horizontal angel to -10° for wall
mounting to get a better view.
Be sure that there is enough space to install the camera and
accessories.
Make sure that the device in the package is in good condition and all the
assembly parts are included.
Make sure that the wall is strong enough to withstand at least 8 times
the weight of the camera and the mount.
Make sure that the power has been disconnected before you wire,
install, or disassemble the device.
Mark Description
Mark Description
Read this manual before using the product.

Symbols and Marks
Notice
Warning
Forbidden
Correct
Incorrect
Turn to page A and continue.
i. Not necessarily included accessory.
ii. Variable accessory amount.
iii. Skip this step if not required.
MicroSD card
Grounding
Disposal
Purchase separately

1

1x 1x
2x
1x
1x 2x 1x
M8×80 HSCM6×16 P0SFUNC1-4-20×12
4x
* 1x
1x 1x
T10 5.0
3
2

1
microSD
1.1*
3
2

2.1
5
4

P0SFUNC1-4-20×12
2.2
5
4

2.3
2.4
HSCM6×16
7
6

2
A.1-A.10 B.1-B.15
2.5
7
6

Ø12mm
M8×80
A.1
A.2
9
8

A.4
A.3
9
8

A.5
11
10

3
A.6
11
10

A.7
13
12

+-
A.8
13
12