HIK VISION DS-2TD4166T-9 User manual

COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
Thermal Bi-spectrum
Network Speed Dome
Quick Start Guide

Thermal Network Speed dome·Quick Start Guide
ii
Quick Start Guide
COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are
the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its
subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter
referred to be “the Manual”) cannot be reproduced, changed, translated, or
distributed, partially or wholly, by any means, without the prior written permission
of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Thermal Bi-spectrum Network Speed Dome.
The Manual includes instructions for using and managing the product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to change,
without notice, due to firmware updates or other reasons. Please find the latest
version in the company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of
Hikvision in various jurisdictions. Other trademarks and logos mentioned below
are the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED
“AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO
YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS
PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION,

Thermal Network Speed dome·Quick Start Guide
iii
IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT
TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE
OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,
VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,
HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT
LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO
ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL
NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.

Thermal Network Speed dome·Quick Start Guide
iv
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly
to avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
The device should be used in compliance with local laws and electrical safety
regulations. Refer to the appropriate documentation for detailed information.
The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra
Low Voltage) and the Limited Power Source (24 VAC/12 VDC). Refer to the
appropriate documentation for detailed information.
DO NOT connect multiple devices to one power adapter, to avoid over-heating
or fire hazards caused by overload.
Make sure the plug is properly connected to the power socket.
If smoke, odor, or noise arises from the device, immediately turn off the power,
unplug the power cable, and contact the service center.
Warnings Follow
these safeguards
to prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

Thermal Network Speed dome·Quick Start Guide
v
The installer and user are responsible for password and security configuration
and its settings.
Both internal and external grounds should be connected properly. (The cross
section area of the grounding wire must be no less than 4 mm2, and no less
than that of the phase connector).
Cautions
Do not drop the device or subject it to physical shock.
Wipe the device gently with a clean cloth and a small quantity of ethanol, if
necessary.
Do not aim the lens at the sun or any other bright light.
When any laser equipment is in use, make sure that the device lens is not
exposed to the laser beam, or it may burn out.
Do not expose the device to high electromagnetic radiation or extremely hot,
cold, dusty, or damp environments.
Place the device in a dry and well-ventilated environment.
Keep non-waterproof devices away from liquids.
Keep the device in original or similar packaging while transporting it.
A few device components (e.g., electrolytic capacitor) require regular
replacement. The average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Improper use or replacement of the battery may result in explosion hazard.
Replace with the same or equivalent type only. Dispose of used batteries in
conformance with the instructions provided by the battery manufacturer.
Never attempt to disassemble the device.
0505021080509

Thermal Network Speed dome·Quick Start Guide
vi
Table of Contents
1Preparation ................................................................................................. 1
2Appearance Description.............................................................................3
2.1 Speed dome Appearance ..................................................................................... 3
2.2 Cable Descriptions ................................................................................................ 4
2.3 Alarm In/Out Connections.................................................................................... 5
3Installing the Speed dome ......................................................................... 6
3.1 Monitoring Distance Range.................................................................................. 7
3.2 Wiring...................................................................................................................... 8
3.3 Installing Memory Card ...................................................................................... 11
3.4 Installing Speed Dome........................................................................................ 11
3.5 Finishing Installing .............................................................................................. 15
4Setting the System over the LAN............................................................. 16
4.1 Wiring.................................................................................................................... 16
4.2 Activating the System......................................................................................... 16
4.2.1 Activation via Web Browser..........................................................................17
4.2.2 Activation via SADP Software.......................................................................17
4.3 Modifying the IP Address ................................................................................... 18
5Operating via Web browser...................................................................... 20
5.1 Accessing the System ........................................................................................ 20
5.2 Live View Page..................................................................................................... 21
6Appendix ................................................................................................... 23
6.1 Common Material Emissivity Reference .......................................................... 23
6.2 Frequently Asked Questions (FAQ) ................................................................... 24
6.2.1 Device Running Error.................................................................................... 24
6.2.2 Device Upgrading.......................................................................................... 24
6.2.3 Others............................................................................................................. 24

Thermal Network Speed dome·Quick Start Guide
1
1Preparation
Basic Requirement
All the electronic operation should be strictly compliance with the electrical
safety regulations, fire prevention regulations and other related regulations
in your local region.
Check the package contents and make sure that the device in the package is
in good condition and all the assembly parts are included.
Use the system according to the working environment requirement.
Checking Installing Environment
Be sure that there is enough space to install the speed dome and
accessories.
Make sure that the wall is strong enough to withstand at least 8 times the
weight of the system and the mount.
Preparing Cables
According to the actual network bandwidth, the Cat5 (in 100M) or Cat6
(100M above) is needed.
When the Speed dome uses standard 24V AC power supply, the power cable
should be American wire gauge 18 or above. The formula of the
cross-section S (mm² ) and the maximum transmission distance L (m) of the
bare wire is L=50*S.
Choose the video cable according to the transmission length. The video
should meet the least demands as: 75Ω resistance; 100% copper core
conducting wire; 95% weaving copper shield.
RS485 communication cable, please refer to Appendix 2
24V AC power cable, please refer to Appendix 3
Preparing Tools
Before installation, please prepare the tools needed, such as the expansion
screws, electric hammer, electric drill, wrench, screwdriver, electroprobe and
network cable.
Original Packaging
When you unpack the speed dome, please keep the original package
properly, in case of returning or repairing the speed dome, you can pack the
speed dome with the package.

Thermal Network Speed dome·Quick Start Guide
2
Note: The user should be responsible for any damage caused when
transporting with unoriginal package.

Thermal Network Speed dome·Quick Start Guide
3
2Appearance Description
There are two kinds of thermal network speed domes: Type I speed dome, and
Type II speed dome. The appearance description of two cameras are shown
below.
2.1 Speed dome Appearance
Refer to the following figures for Type I thermal speed dome overview and
dimensions.
1
2
3
4
5
6
7
8
RED AC24V
YELLOW/GREEN
BLACK AC24V
ORANGE RS485+
YELLOW
RS485-
Type I Speed Dome Type II Speed Dome
Figure 2-1 Thermal Speed dome Overview

Thermal Network Speed dome·Quick Start Guide
4
Table 2-1 Descriptions of Cable Interface
No.
Description
1
Network Cable
2
Video Cable
3
Alarm Out
4
Audio Cable
5
Alarm In
6
RS-485
7
Power Cable
8
SD Card Slot
2.2 Cable Descriptions
The cable interfaces of speed dome are shown in Figure 2-2. The cables of
RS-485, power supply, alarm inputs, alarm outputs, etc. are distinguished by
different colors. Please refer to the labels attached on the cables for identification.
VIDEO
RED AC24V
YELLOW/GREEN
BLACK AC24V
YELLOW R485
-
ORANGE R485 +
Power Cable
RS485-
RS485+
Video Cable
Alarm Inputs
Network Cable
Alarm Outputs
Audio Input / Output
Figure 2-2 Cables of Other Speed domes