HIK VISION US-5 Inch Speed Dome User manual

5 Inch Speed Dome
Installation Manual
V2.0.0
2010-01

5 Inch Speed Dome Installation Manual V2.0.0
1
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
This manual is applicable to 5 Inch Speed Dome.
This manual may contain several technically incorrect places or printing errors, and the content is subject to change without notice.
The updates will be added into the new version of this manual. We will readily improve or update the products or procedures described
in the manual.

5 Inch Speed Dome Installation Manual V2.0.0
2
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution
measure is divided into “Warnings” and “Cautions”:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings Follow these safeguards to prevent serious
injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.
Warnings
1. In the use of the product, you must be strict compliance with the electrical safety regulations of the nation and region.
2. Please use the power adapter, which is provided by normal company. The standard of the power adapter is AC24V/3A.
3. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
4. Please make sure that the plug is firmly connected on the power socket.
5. When the product is installed on wall or ceiling, the device shall be firmly fixed.
6. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the
service center.
7. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
Warnings
1. Do not drop the dome or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment
installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
2. Do not place the dome in extremely hot, cold (the operating temperature shall be -30°C ~ +65°C), dusty or damp locations, or fire or
electrical shock will occur otherwise.
3. The dome cover for indoor use shall be kept from rain and moisture.
4. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can
cause fire danger).
5. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction
however), and affecting the endurance of CCD at the same time.
6. Please use the provided glove when open up the dome cover, avoid direct contact with the dome cover, because the acidic sweat of
the fingers may erode the surface coating of the dome cover.
7. Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, not to use alkaline detergents.

5 Inch Speed Dome Installation Manual V2.0.0
3
Preparation for Installation
1. Basic requirements
1) All the electronic operation should be strict compliance with the local electrical safety regulations, fire prevention
regulations and other related regulations at the installation place.
2) Check whether all the accessories are there according to the packing list, make sure that the place and installation mode are
conform to the demands, if not, please contact the supplier.
3) Please use this product according to the working environment.
2. Check installation space.
Make sure the place have enough space to install the speed domes and its accessories.
3. Check the intensity of conformation at the installation scene.
Please make sure that the endure ability of ceilings or walls is 4 times as the weight of speed dome and its accessories.
4. Preparation of cables
Choose the video cable according to the transmission length. The video should meet the least demands as:
1. 75Ωresistance
2. 100% copper core conducting wire.
3. 95% weaving copper shield.
RS485 communication cable, please refer to Appendix 2
24V AC power cable, please refer to Appendix 3
5. Please keep all wrappers
Please keep all wrappers after unpack them for future use. In case of any failure occurred, please return the speed dome to the
factory with the original wrapper.
Note: Transportation without the original wrapper may result in damage on the speed dome and cost additional charge.

5 Inch Speed Dome Installation Manual V2.0.0
4
Table of Contents
Table of Contents......................................................................................................................................................... 4
Chapter 1 Installation................................................................................................................................................... 6
1.1 ............................................................................................................................................. 6Check Parts List
1.2 ..................................................................................................................................................... 6Installation
1.2.1 ....................................................... 6High Speed Dome and Auto Tracking Speed Dome Installation
1.2.2 ............................... 10Medium Speed Dome and Network High-definition Speed Dome Installation
1.3 .............................................................................................................................................. 14Initial Settings
1.4 ..................................................................................................................................... 15DIP Switch Settings
1.4.1 ........................ 15DIP Switch Settings for High Speed Dome and Auto Tracking High Speed Dome
1.4.2 .. 16DIP Switch Settings for Medium Speed Dome and Network High-definition High Speed Dome
1.4.3 .............................................................................................................................. 16Address Settings
1.4.4 ........................................................................................................................... 19Baud Rate Settings
1.4.5 .............................................................................................................................. 19Protocol Settings
1.4.6 .......................................................................................................... 19Simplex/Half-duplex Settings
1.4.7 .......................................................................................................... 19Terminating Resistor Settings
1.5 ........................................................................................................................... 19Alarm In/Out Connections
Chapter 2 Mounts Dimension.................................................................................................................................... 21
2.1 Long-arm Wall Mount ................................................................................................................................. 21
2.2 Short-arm Wall Mount ................................................................................................................................. 22
2.3 Corner Adapter............................................................................................................................................. 22
2.4 Pole Adapter................................................................................................................................................. 23
2.5 Pendant Adapter........................................................................................................................................... 23
Chapter 3 Wall Mounting Applications ..................................................................................................................... 24
3.1 Mounting Components ................................................................................................................................24
3.2 Wall Mounting Instructions ......................................................................................................................... 24
Chapter 4 Corner Mounting Applications.................................................................................................................. 27
4.1 Mounting Components ................................................................................................................................27
4.2 Corner Mounting Instructions...................................................................................................................... 28
Chapter 5 Pole Mounting Applications...................................................................................................................... 30
5.1 Mounting Components ................................................................................................................................30
5.2 .......................................................................................................................... 31Pole Mounting Instructions
Chapter 6 Pendant Mounting Applications................................................................................................................ 34
6.1 Mounting Components ................................................................................................................................34
6.2 .................................................................................................................... 35Pendant Mounting Instructions
Chapter 7 Surface Mounting Applications................................................................................................................. 37
7.1 Wiring .......................................................................................................................................................... 37
7.2 ................................................................................................................................................. 37Install Dome
Chapter 8 In-ceiling Mounting Applications ............................................................................................................. 41
8.1 Installation Conditions................................................................................................................................. 41
8.2 In-ceiling Mounting Instructions ................................................................................................................. 41
Appendix 1 Lightning & Surge Protection ................................................................................................................ 46

5 Inch Speed Dome Installation Manual V2.0.0
5
Appendix 2 RS485 Bus Connection .......................................................................................................................... 47
Appendix 3 24VAC Wire Gauge & Transmission Distance ...................................................................................... 50
Appendix 4 Table of Wire Gauge Standards.............................................................................................................. 51

5 Inch Speed Dome Installation Manual V2.0.0
6
Chapter 1 Installation
1.1 Check Parts List
Prior to installation, unpack the dome unit and check whether it is in good condition and all parts and accessories are included by
referring to the packing list).
Note: The power supply for the speed dome is AC24V/3A.
1.2 Installation
1.2.1 High Speed Dome and Auto Tracking Speed Dome Installation
Note: The following installation instructions are applicable to high speed dome, network high speed dome, auto tracking high speed
dome and auto tracking network high speed dome models.
1. Install the dome mount. Please refer to the related sections from Chapter2 to Chapter7 for specific installation methods of different
mounts.
2. Open the bubble and remove the expand aple poly ethylene and protective sticker from the dome drive. Refer to Figure 1.2.1.
Protective sticker
Expand aple poly ethylene
Figure 1.2.1 Open bubble and remove the expand aple
poly ethylene and protective sticker from dome drive
3. Configure the dome address, baud rate and other settings through DIP switch SW1 and SW2 located on the bottom board of the
dome, as shown in Figure 1.2.2. Please refer to Section 1.4 DIP Switch Settings for setting address, baud rate, communication protocol,

5 Inch Speed Dome Installation Manual V2.0.0
7
etc.
1 2
3 4
1. Address DIP Switch 2. Protocol DIP Switch
3. Wirin
g
Connector 4. Address and Protocol Settin
g
s
Figure 1.2.2 Bottom Board of Dome Drive
4. Push the tab locks on the back box interconnect board and lift the hinged door to the circuit board, as shown in Figure 1.2.3. Unplug
the video cable, power cord and other cables terminals to avoid cables twisting during the back box installation. Refer to Figure 1.2.4
(high speed dome) and Figure 1.2.5(network high speed dome) for the wiring terminals.
1
2
3
1. Tab Lock
2. Wiring Connector
4. Power LED Indicator
3. Lock Clips
4
Figure 1.2.3 Back Box Interconnect Board

5 Inch Speed Dome Installation Manual V2.0.0
8
3
1. Alarm In/Out Terminals (7 inputs/2outputs)
2. Video Out and RS-485 COM Terminals
2
1
3. 24VAC Voltage Input and GND Terminals
Figure 1.2.4 Back Box Circuit Board (High Speed Dome and Auto Tracking High Speed Dome)
3
1.Alarm In/Out Terminals (7 inputs/2 outputs)
2
2. Audio In/Out, Video Out and
RS-485 COM Terminals
1
3. 24V
AC Voltage Input and GND
Figure 1.2.5 Back Box Circuit Board (Network High Speed Dome and Auto Tracking Network High Speed Dome)

5 Inch Speed Dome Installation Manual V2.0.0
9
5. Attach the back box of dome to the mount.
Figure 1.2.6 Attach Back Box to Mount
Note: for outdoor applications, please apply the thread compound and the damp-proof stopper to threads of the back box and the
mount.
After having made connections of the power cord, video cable, RS-485 control line and alarm input/output lines (if required), close the
hinged door and tighten the set screws, as shown in Figure 1.2.6.
6. Install the dome drive
As shown in Figure 1.2.7, align the tabs on both sides of the dome drive with the corresponding arrow labels on the back box to snap
the drive into the back box firmly.
Figure 1.2.7 Install Dome Drive

5 Inch Speed Dome Installation Manual V2.0.0
10
7. Install the bubble and fasten the two set screws on both sides, as shown in Figure 1.2.8.
Figure 1.2.8 Install Bubble
1.2.2 Medium Speed Dome and Network High-definition Speed Dome
Installation
Note: the following installation instructions are applicable to high speed dome, network high speed dome and High-definition network
speed Dome models.
1. Install the dome mounts. Please refer to the related sections from Chapter2 to Chapter7 for specific installation methods of different
mounts.
2. Open the bubble and remove the expand aple poly ethylene and protective sticker from the dome drive. Refer to Figure 1.2.9.
Expand aple poly ethylene Protective sticker

5 Inch Speed Dome Installation Manual V2.0.0
11
Figure 1.2.9 Open bubble and remove the expand aple
poly ethylene and protective sticker from dome drive
3. Configure the dome address, baud rate and other settings through DIP switch SW1 and SW2 located on the bottom board of the
dome, as shown in Figure 1.2.10. Please refer to Section 1.4 DIP Switch Settings for setting address, baud rate, communication
protocol, etc.
1
2
1. Wiring Connector 2. Address and Protocol Settings
Figure 1.2.10 Bottom Board of Dome Drive
Figure 1.2.11 Medium Speed Dome DIP Switch

5 Inch Speed Dome Installation Manual V2.0.0
12
4. Push the tab locks on the back box interconnect board and lift the hinged door to the circuit board, as shown in Figure 1.2.12.
Unplug the video cable, power cord and other cables terminals to avoid cables twisting during the back box installation. Refer to
Figure 1.2.13 (medium speed dome) and Figure 1.2.14(network medium speed dome) for the wiring terminals.
1
2
3
1. Tab Lock
2. Wiring Connector
3. Lock Clips
4. Power LED Indicator
4
Figure 1.2.12 Back Box Interconnect Board
3
1. Alarm In/Out Terminals (1 inputs/1outputs)
2. Video Out and RS-485 COM Terminals
2
1
3. 24VAC Voltage Input and GND Terminals
Figure 1.2.13 Back Box Circuit Board(Medium Speed Dome)

5 Inch Speed Dome Installation Manual V2.0.0
13
3
1.Alarm In/Out Terminals (1 inputs/1 outputs)
2
2. Audio In/Out, Video Out and
RS-485 COM Terminals
1
3. 24V
AC Voltage Input and GND
Figure 1.2.14 Back Box Circuit Board (Network Medium Speed Dome and Network High-definition Speed Dome)
5. Attach the back box of dome to the mount.
Figure 1.2.15 Attach Back Box to Mount

5 Inch Speed Dome Installation Manual V2.0.0
14
Note: for outdoor applications, please apply the thread compound and the damp-proof stopper to threads of the back box and the
mount.
After having made connections of the power cord, video cable, RS-485 control line and alarm input/output lines (if required), close the
hinged door and tighten the set screws, as shown in Figure 1.2.15.
6. Install the dome drive
As shown in Figure 1.2.16, align the tabs on both sides of the dome drive with the corresponding arrow labels on the back box to snap
the drive into the back box firmly.
Figure 1.2.16 Install Dome Drive
7. Install the bubble and fasten the two set screws on both sides, as shown in Figure 1.2.17.
Figure 1.2.17 Install Bubble
1.3 InitialSettings
Address code: 0
Baud rate: 2400
120Ωterminator: OFF

5 Inch Speed Dome Installation Manual V2.0.0
15
1.4 DIP Switch Settings
1.4.1 DIP Switch Settings for High Speed Dome and Auto Tracking High
Speed Dome
1 2
3 4
1. Address DIP Switch 2. Protocol DIP Switch
3. Wiring Connector 4. Address and Protocol Settings
Figure 1.4.1 Bottom Board of Dome Drive
The dome provides two DIP switches SW1 and SW2 for setting the dome address, baud rate, protocol, etc. As shown in Figure 1.4.1,
ON=1, OFF=0. In SW1 and SW2, 1 is the lowest position and 8 is the highest position. Please refer to the following list for specific
settings:
Note: As the high speed dome is capable of being self-adaptive to PELCO-D, PELCO-P, PRIVATE-Code, VICON and KALATEL-32
protocols, and the network speed dome is self-adaptive to Pelco-P, Pelco-D and PRIVATE-Code protocols as well, no DIP switch
settings for control protocol are required.

5 Inch Speed Dome Installation Manual V2.0.0
16
1.4.2 DIP Switch Settings for Medium Speed Dome and Network
High-definition High Speed Dome
Figure 1.4.2 DIP Switch Location on Side of Dome Drive
The circuit board of the dome drive provides two DIP switches SW1 and SW2 for setting the dome address, baud rate, protocol, etc. As
shown in Figure 1.4.2, ON=1, OFF=0. In SW1 and SW2, 1 is the lowest position and 8 is the highest position. Please refer to the
following list for specific settings:
Note: The network speed dome is self-adaptive to Pelco-P, Pelco-D and PRIVATE-Code protocols, no DIP switch settings for control
protocol are required.
1.4.3 Address Settings
The DIP Switch SW1 is used for setting the dome address:
DomeAddress SW1Settings 12345678
0 OFF OFF OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF OFF OFF
255 ON ON ON ON ON ON ON ON

5 Inch Speed Dome Installation Manual V2.0.0
17
Settings for address 0~71 are listed as below:
SW1 Position DIP Switch SW1 Settings
Address 1 2 3 4 5 6 7 8
0 OFF OFF OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF ON OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF
6 OFF ON ON OFF OFF OFF OFF OFF
7 ON ON ON OFF OFF OFF OFF OFF
8 OFF OFF OFF ON OFF OFF OFF OFF
9 ON OFF OFF ON OFF OFF OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF
13 ON OFF ON ON OFF OFF OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF
15 ON ON ON ON OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF
17 ON OFF OFF OFF ON OFF OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF
19 ON ON OFF OFF ON OFF OFF OFF
20 OFF OFF ON OFF ON OFF OFF OFF
21 ON OFF ON OFF ON OFF OFF OFF
22 OFF ON ON OFF ON OFF OFF OFF
23 ON ON ON OFF ON OFF OFF OFF
24 OFF OFF OFF ON ON OFF OFF OFF
25 ON OFF OFF ON ON OFF OFF OFF
26 OFF ON OFF ON ON OFF OFF OFF
27 ON ON OFF ON ON OFF OFF OFF
28 OFF OFF ON ON ON OFF OFF OFF
29 ON OFF ON ON ON OFF OFF OFF
30 OFF ON ON ON ON OFF OFF OFF
31 ON ON ON ON ON OFF OFF OFF
32 OFF OFF OFF OFF OFF ON OFF OFF
33 ON OFF OFF OFF OFF ON OFF OFF
34 OFF ON OFF OFF OFF ON OFF OFF
35 ON ON OFF OFF OFF ON OFF OFF
36 OFF OFF ON OFF OFF ON OFF OFF
37 ON OFF ON OFF OFF ON OFF OFF
38 OFF ON ON OFF OFF ON OFF OFF

5 Inch Speed Dome Installation Manual V2.0.0
18
39 ON ON ON OFF OFF ON OFF OFF
40 OFF OFF OFF ON OFF ON OFF OFF
41 ON OFF OFF ON OFF ON OFF OFF
42 OFF ON OFF ON OFF ON OFF OFF
43 ON ON OFF ON OFF ON OFF OFF
44 OFF OFF ON ON OFF ON OFF OFF
45 ON OFF ON ON OFF ON OFF OFF
46 OFF ON ON ON OFF ON OFF OFF
47 ON ON ON ON OFF ON OFF OFF
48 OFF OFF OFF OFF ON ON OFF OFF
49 ON OFF OFF OFF ON ON OFF OFF
50 OFF ON OFF OFF ON ON OFF OFF
51 ON ON OFF OFF ON ON OFF OFF
52 OFF OFF ON OFF ON ON OFF OFF
53 ON OFF ON OFF ON ON OFF OFF
54 OFF ON ON OFF ON ON OFF OFF
55 ON ON ON OFF ON ON OFF OFF
56 OFF OFF OFF ON ON ON OFF OFF
57 ON OFF OFF ON ON ON OFF OFF
58 OFF ON OFF ON ON ON OFF OFF
59 ON ON OFF ON ON ON OFF OFF
60 OFF OFF ON ON ON ON OFF OFF
61 ON OFF ON ON ON ON OFF OFF
62 OFF ON ON ON ON ON OFF OFF
63 ON ON ON ON ON ON OFF OFF
64 OFF OFF OFF OFF OFF OFF ON OFF
65 ON OFF OFF OFF OFF OFF ON OFF
66 OFF ON OFF OFF OFF OFF ON OFF
67 ON ON OFF OFF OFF OFF ON OFF
68 OFF OFF ON OFF OFF OFF ON OFF
69 ON OFF ON OFF OFF OFF ON OFF
70 OFF ON ON OFF OFF OFF ON OFF
71 ON ON ON OFF OFF OFF ON OFF

5 Inch Speed Dome Installation Manual V2.0.0
19
1.4.4 Baud Rate Settings
The positions 1-3 of DIP Switch SW2 are used for setting the baud rate of dome, respectively as 2400bps, 4800bps, 9600bps,
19200bps and 38400bps. For baud rate out of the above range, the default setting is 2400bps. Refer to the following table:
DIP Switch SW2-Baud Rate Settings
Baud Rate Positions1-3 Settings 1 2 3
2400 ON OFF OFF
4800 OFF ON OFF
9600 ON ON OFF
19200 OFF OFF ON
38400 ON OFF ON
1.4.5 Protocol Settings
The positions 4-6 of DIP Switch SW2 are used for setting the communication protocols of dome. Refer to the following table (network
speed dome model does not support Manchester code protocol):
DIP Switch SW2-Protocol Settings
Protocol Positions 4-6 Settings 4 5 6
Bosch Manchester OFF ON ON
AD Manchester ON ON ON
Self-adaptive Others
1.4.6 Simplex/Half-duplex Settings
The position 7 of DIP Switch SW2 is used for setting the communication method of dome to simplex or half-duplex.
DIP Switch SW2-Simplex/Half-duplex Settings
Description Position 7 Setting 7
Simplex OFF
Half-duplex ON
1.4.7 Terminating Resistor Settings
The position 8 of DIP Switch SW2 is used for setting the terminating resistor of dome.
DIP Switch SW2-Terminating Resistor Settings
Description Position 8 Setting 8
Not Terminated OFF
Terminated ON
1.5 Alarm In/Out Connections
The high speed dome, network speed dome, auto tracking high speed dome and the auto tracking network speed dome can be
connected with 7 alarm inputs (0~12VDC) and 2 alarm outputs; and the medium speed dome, network high speed dome and the