Hillsdale Furniture Urban Quarters 101815-104785 User manual

To help prevent serious or fatal injuries from entrapment or falls:
• Follow the information on the warnings appearing on the upper bunk end structure
and on the carton. Do not remove warning label from bed.
• Always use the recommended size mattress or mattress support, or both, to help
prevent the likelihood of entrapment or falls.
• Use only mattress which is 74-75 inches long and 53-1/2 - 54-1/2 inches wide on
upper and lower bunks. Ensure thickness of mattress and foundation combined
does not exceed 8 inches and that mattress surface is at least 5 inches (127 mm)
below the upper edge of guardrails.
• Do not allow children under 6 years of age to use the upper bunk.
• Prohibit more than one person on the upper bunk at all times.
• Periodically check and ensure that the guardrail, ladder, and other components are
in their proper position, free from damage, and that all connectors are tight.
• Do not allow horseplay on or under the bed and prohibit jumping on the bed.
• Always use the ladder for entering and leaving the upper bunk.
• Do not use substitute parts.
Contact the manufacturer or dealer for replacement parts.
• Use of a night light may provide added safety precaution for a child using the
upper bunk.
• Always use guardrails on both long sides of the upper bunk. If the bunk bed will be
placed next to the wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and wall.
• The use of water or sleep flotation mattresses is prohibited.
• STRANGULATON HAZARD - Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example: but not limited to - hooks, belts,
and jump ropes.
! IMPORTANT !
Keep these instructions for future reference.

Examine all packaging material for small parts that may have come loose during shipment. Periodic checks are recommended to insure that all
components are in proper position, tight and free from damage. Keep this assembly instruction for future reference. Adult assembly is required.
The product of Hillsdale Furniture, LLC is designed for residential use only. Customer Service Phone Number: 502-562-0000
Date: 08-17-2015
Page 1 of 2
URBAN QUARTERS METAL TWIN/TWIN BUNK BED
101815-104785 (1265-012A) Sides and Deck
101813-104783 (1265-012B) Guard Rails
HARDWARE LIST
A (8) M8 x 95mm Allen Bolts
B (8) 1/4” x 2-3/4” Allen Bolts
C (12) 1/4” x 1-1/4” Allen Bolts
D (8) M8 Connector
E (1) 4mm Allen Wrench
F (1) 5mm Allen Wrench
PARTS LIST
G (1) Open End Panel
H (1) Full End Panel
I (2) Side Rails
J (4) Frame Supports
K (6) Deck Panels
QTYPART
12C
1E
HARDWARE QTYPART HARDWARE
8
1
D
8A 8B
F
CARE & MAINTENANCE : The touch ofa soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
as they may cause damage to the finish. Periodic checks are recommended to make sure that all hardware is securely tightened.
HDFBP
H
GJ
J
J
J
AA
A
A
A
A
A
A
A
A
AA
A
A
A
A
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
FIGURE 1
STEP 1 - Figure 1
Begin assembly by inserting Frame Supports (J) down into
slots on Open End Panel (G) and Full End Panel (H). Insert
Connectors (D) into sides of Frame Supports (J) and secure
from end panels with Allen Bolts (A). Tighten bolts with
Allen Wrench (F) provided.

URBAN QUARTERS METAL TWIN/TWIN BUNK BED
101815-104785 (1265-012A) Sides and Deck
101813-104783 (1265-012B) Guard Rails
STEP 2 - Figure 2
Insert Deck Panels (K) down in between Frame Supports (J)
and secure each panel with 2 Allen Bolts (C). Tighten
bolts using Allen Wrench (E) provided.
Date: 08-17-2015
Page 2 of 2
CARE & MAINTENANCE : The touch ofa soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
as they may cause damage to the finish. Periodic checks are recommended to make sure that all hardware is securely tightened.
FIGURE 2
FIGURE 3
K
K
K
K
K
K
J
J
BB
B
B
B
B
B
B
BB
BB
B
B
BB
STEP 3 - Figure 3
Finally attach Side
Rails (I) to End
Panels (G & H) using
1 Allen Bolt (B) per
side. Secure Side
Rails (I) to Frame
Supports (J) with 2
Allen Bolts (B) per
side. Tighten all bolts
using Allen Wrench
(E) provided. The
assembly is now
complete.
I
I
H
G
J
CC
CC
CC CC
CC
CC