HIOTH TECHNOLOGY CO., LTD CT-SMEA2001-ID User manual

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
DOOR/WINDOW DETECTOR
Introduction
In general, there are two ways for criminals to break into a flat: one is to steal to the master
key, and then open the door; the second is use tools to open the door. No matter what ways the
criminals are using, he must open the door/window of the house. Once a thief pushes the door, the
door and the door frame will displacement, the door sensor and magnet will produce a shift, and
Door/Window Detector will send alarm signals to remind staff to take safety measures.
The Door/Window Detector is a device with built-in EnOcean module. This device can be
included and operated in any EnOcean network with other EnOcean certified devices from any
other manufactures. It is a passive wireless sensor. With the magnet, the sensor detects "open" or
"close" status (door or window).
CT-SMEA2001-ID
Door/Window Detector

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
Technical Information
Compatible with any EnOcean network controller
Without external power supply
With the magnet, the sensor detects "open" or "close" status (door or window).
Easy to install
Long service life
Specifications
Radio protocol: EnOcean 868.3MHz
Data rate/Modulation type: 125kbps/ASK
Power supply: Wireless passive, Solar energy or use CR1216 battery, and the optional
CR1216 battery (not included) for dark area use (5 years in total darkness)）
Initial operation time in darkness @ 25°C: typ. 6 days, min. 90 hours if energy storage fully
charged transmission of telegram every 25 min on average
Operation start up time with empty energy store: typ. 2.5 min @ 400 lux / 25°C incandescent
or fluorescent light
Temperature range：0～40℃
Working range: 30m
Dimension：80mm×26mm×18mm
Operation
Including of EnOcean network
1) Choose "Enocean" to enter the Network Inclusion mode on the APP, and input the Apparatus

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
ID, then click " ".
2) Press the pairing button on the back in 8 seconds (open the rear lid).
3) When prompt a message “Request Access Success”, please go to the device list interface, and
refresh the device list, the device will be displayed.
Installation Instructions
It’s recommended to install the Door/Window Detector in dry interior locations.
Installation Tips
The Door/Window Detector installation is very convenient. Even people who do not understand
the knowledge of electrical equipment can be very convenient to install. You can place it at any
door / window. Just need to stick the back of the Door/Window Detector with double-sided adhe-
Pairing Button

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
sive, and stick it to the door or window. If you want to replace the installation position in the fu-
ture, you can also take off the detector, and stick the device once more time.
DOOR/WINDOW DETECTOR INSTALLATION
Decide which doors/windows to be protected by Door/Window Detectors, (usually the front and
back doors as a minimum will have Door/Window Detectors fitted). Additional detectors may also
be fitted where required to other vulnerable doors or windows (e.g. garage, patio/conservatory
doors etc.).
1. Ensure that the system properly powered
The Door/Window Detector is a passive wireless sensor, supplied by solar energy (or use
CR1216 battery).
2. Using the adhesive tape to fit detector on the door or window.
3. Fit the magnet to the moving part of the door/window opposite the detector using the adhe-
sive tape.
4. Ensure that the parallel gap between the magnet and detector is less than 15mm and that the
matching line on the magnet is pointing towards and aligned with the line on the detector.
5. After proper installation and test, put the battery cover back to the detector and the detector
enters the normal.
Safety Notice
During installation, protect the device from any physical damage by dropping or bumping. If
happened, please contact the supplier for maintenance.
Keep the device away from acid-base and other corrosive solids, liquids, gases, to avoid
damage.
Avoid overexertion during operation, to protect device from mechanical damage.
Pay attention to the using range.
Read all instructions and documentation and save for future reference.