Alula RE210T User manual

Ceiling
Floor
The Indoor Motion Sensor alarms when motion is sensed
or when the external contact is opened. It is battery
powered and requires no installation tools. A Pyroex™
sensor with HighBar™signal processing allows for industry-
leading pet immunity and catch performance.
Features
• Industry-leading pet immunity and catch performance
• Supports both motion zone and an external contact zone
• Mountable on walls or in corners
• 5 year warranty
Enroll by placing the panel into wireless enrollment mode
and then sending a sensing event (e.g. tamper, motion, or
external contact trip).
Enrollment Tips
• Power down the sensor after enrollment
because the panel may mistakenly double
enroll the sensor if it is tripped again while you
are walking over to enroll the next sensor.
• Use loop 3 for the external contact. Loop 2 will
NOT work.
Motion Enrollment Panel Questions
• Select RF sensor # (01 to 48)
• Select RF sensor type
• Select RF sensor equip type
• Select RF sensor equip code
• Select RF sensor other equip code*
• Select RF sensor serial number
• Select RF sensor age
• Select RF sensor loop number
Select a zone number
[04] Interior Follower
[2] Motion
[0000] Other or [0869] PIR w/Pet Immunity
[0] Other
Press Shift, Press Learn, Trip sensor
[1] New
[1] Motion
External Contact Enrollment Panel Questions
• Select RF sensor # (01 to 48)
• Select RF sensor type
• Select RF sensor equip code
• Select RF sensor other equip code*
• Select RF sensor serial number
• Select RF sensor age
• Select RF sensor loop number
Select a zone number
[03] Perimeter
[0000] Other or [0862] Thin door window
[0] Other
Press Shift, Press Learn, Trip sensor
[1] New
[3] Additional Input
* Option not present in GC3 panel
Verify proper enrollment and operation using your control panel’s installation manual.
I
N
S
T
A
L
L
G
U
I
D
E
I
Resolution Compatibles
RE210T Indoor Motion Sensor
-Pet Immune 2GIG™Compatible

Pro Tips
Walk test mode is entered by pressing the motion
sensor’s tamper button. The walk test lasts three
minutes.
Walk Test Operation
• The walk test LED turns on when motion
is sensed.
• The motion sensor performs a
re-calibration after each activation. The
re-calibration takes about 30 seconds.
The sensor will NOT sense motion
during the re-calibration.
• Wireless transmissions are sent for each
detection, so walk test mode can also
be used to test the panel.
3M VHB tape works great if the surface is properly
prepared and rm pressure is applied for over 10
seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface
temperature is above 50 °F
Motion lockout is active for three minutes after a motion event is detected. During the
motion lockout period, motion events will be ignored.
Motion sensitivity can be adjusted by the sensitivity jumper on the circuit board.
• Jumper Installed (lower sensitivity): Detects person in 3 to 5 steps.
Increases pet immunity. Usually for security applications.
• Jumper NOT Installed (higher sensitivity): Detects person in 2 to 4 steps.
Usually for occupancy applications.
Walk Test LED
Cover Tamper Switch
Battery
Bug Foam IR Sensing Element
Sensitivity
Low - Jumper ON
High - Jumper OFF
External Contact
Install using the included 3M VHB®tape to adhere the motion
sensor on a wall or in a corner. The tape should be applied
to the back when wall mounting or to the back bevels when
corner mounting. Alternatively, screw mounting can be done
by punching out the screw mounting holes.
Installation Tips
• Mount 7.5 to 9.5 feet from the oor for an optimal
balance between catch performance and pet
immunity.
• Remove the cover and circuit board before trying
to punch out the screw mounting holes.
• Ensure the bug foam stays intact and snug around
the IR sensing element when re-installing the
circuit board.
External Contact (not evaluated by ETL)
• Use a normally-closed contact because the motion sensor will transmit an
alarm when it sees the external contact open.
• Do not use end-of-line resistors.
Mounting Screw Holes

Side eld of view for a mounting height of 7.5 feet
0
10ft
20ft
30ft
40ft
Top eld of view
010ft 10ft20ft 20ft30ft 30ft
7.5ft
3.2ft
010ft 20ft 30ft 40ft
3.2ft
9.5ft
6.4ft
010ft 20ft 30ft 40ft
Side eld of view for a mounting height of 9.5 feet
Pro Tips
Pet immunity is optimized when the motion sensor is mounted at 7.5 to 9.5 feet high
and aimed away from house features that could allow pets to be high in the detection
eld (e.g. stairs, counter tops, tall furniture).
Motion catch performance is best when the motion sensor is positioned so a person
would typically walk across the front of the motion sensor instead of directly toward
the motion sensor.
Motion Detection Tips
• Provide a clear line-of-sight to the monitored area and remember that glass
blocks infrared energy.
• Aim away from windows and sunlight.
• Aim away from air conditioners, heaters or heating/cooling vents.
Accessories
Gimbal mount (RE019 and RE019-10) allows the motion sensor direction to be adjusted
after mounting on a wall.
Horizontal beam lens (RE020) has less look-down which results in increased pet
immunity.
Specications
7.5ft
0 10ft 20ft 30ft 40ft
3.2ft

47-0005-05 • RevC • 2018-03-27
Tech Support Line • (888) 88-ALULA • [phone]
alula.net
WARRANTY
Alula will replace all non-portable products that are defective in
their rst ve (5) years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE210
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could void
the user’s authority to operate this equipment.
FCC ID: U5X-RE210
TRADEMARKS
Alula is a trademark owned by Alula Holdings, LLC.
“2GIG” is a trademark owned by Nortek Security & Control, LLC.
Alula products will function with 2GIG systems. However, no Alula
product is produced by, endorsed by, or is ofcially associated with
2GIG.
Alula recommends verifying proper enrollment and operation, per
control panel installation instructions, at installation.
Specications
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.50 x 2.40 x 1.70 inches (8.9 x 6.1 x 4.3 cm)
3.2 ounces (91 grams)
3M VHB (Very High Bond) Tape or Screws (both provided)
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Pet Immunity
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Optimal Mounting Height
Transmitted Indications
345 MHz
Two 60-pound dogs or one 85-pound dog
One Panasonic CR132A
6 to 8 years
3.0 VDC (Nominal), 2.2 VDC (Low)
30 mA (Maximum), 20 uA (Quiescent)
7.5 to 9.5 feet (2.3 to 3.0 m)
Cover Tamper, Low Battery, Supervision
Certication
RE210T UL639, ULC-S309-03, ETL, FCC, IC
Specications subject to change without notice.