Hirschmann OCTOPUS OS3 User manual

Installation OCTOPUS OS3
Release 01 02/2019
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Managed Ethernet Switch
OCTOPUS OS3

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2019 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
8.2.19

Installation OCTOPUS OS3
Release 01 02/2019 3
Contents
Safety instructions 5
About this manual 10
Key 11
1 Description 12
1.1 General device description 12
1.2 Device name and product code 12
1.3 Device views 14
1.3.1 Front view 14
1.4 Power supply 15
1.4.1 Supply voltage with the characteristic value N9 15
1.5 Ethernet ports 15
1.6 Pin assignments 16
1.7 Display elements 17
1.7.1 Device state 17
1.7.2 Port Status 19
1.8 Management interfaces 20
1.8.1 V.24 interface (external management) 20
1.8.2 USB interface 20
1.9 Input/output interfaces 21
1.9.1 Signal contact 21
2 Installation 22
2.1 Checking the package contents 22
2.2 Installing and grounding the device 23
2.2.1 Mounting on a flat surface 23
2.2.2 Grounding the device 24
2.3 Connecting the supply voltage 25
2.4 Connecting data cables 26
3 Basic Settings 27
4 Monitoring the ambient air temperature 28
5 Maintenance and service 29

4Installation OCTOPUS OS3
Release 01 02/2019
6Disassembly 30
6.1 Removing the device 30
7 Technical data 31
7.1 General data 31
7.2 Supply voltage 31
7.3 Signal contact 32
7.4 Power consumption/power output 32
7.5 Climatic conditions during operation 33
7.6 Climatic conditions during storage 33
7.7 Dimension drawings 34
7.8 EMC and immunity 35
7.9 Network range 38
8 Scope of delivery, order numbers and
accessories 39
8.1 Scope of delivery 39
8.2 Accessories 39
9 Underlying technical standards 40
A Further support 41

Installation OCTOPUS OS3
Release 01 02/2019 5
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 31.
Connect to the product only components suitable for the requirements
of the specific application case.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation OCTOPUS OS3
Release 01 02/2019
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Installation site requirements
Verify that there is at least 4 in (10 cm) of space above and below the
device.
Install this device solely in an operating site with restricted access, to
which maintenance staff have exclusive access. Install the device in
such a way that it is protected against mechanical forces in the area of
the power supply.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the cooling fins free to ensure good air circulation.
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
To preserve the suitability of your device for IP54, seal all unused
connections and ports with the provided plastic protection screws. See
“Scope of delivery” on page 39. See “Scope of delivery” on page 39 in
case of an additional demand.
To preserve the IP54 suitability for your device, exclusively connect
components with degree of protection IP54.
For operation according to EN 45545: Seal all unused connections
and ports exclusively with metal protection screws and metal screw
caps. The use of plastic protection screws is prohibited.
Protection screws and screw caps made of metal are available as an
accessory.
See “Accessories” on page 39.

Installation OCTOPUS OS3
Release 01 02/2019 7
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the grounding connector on the front panel as a conductor.
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
General requirements for connecting electrical wires
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
Relevant for North America:
Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.
Requirements for connecting the signal contact
The following requirements apply without restrictions:
The connected voltage complies with the requirements for a safety extra-low voltage
(SELV) or ES1 as per IEC/EN 62368-1.
The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.
See “General data” on page 31.
Requirements for connecting the supply voltage
The following requirements apply without restrictions:
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the type plate of the device.
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device (for example a switch or
a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is
clear which disconnecting device belongs to which power supply cable.
The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on
the supply voltage input.
The following requirements apply alternatively:
Relevant when the device is supplied via 1 voltage input:
Relevant for North America:
The power supply complies with the requirements according to NEC Class 2.

8Installation OCTOPUS OS3
Release 01 02/2019
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/30/EU (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
www.hirschmann.com
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55032
Safety: EN 62368-1
You find more information on technical standards here:
See “Technical data” on page 31.
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

Installation OCTOPUS OS3
Release 01 02/2019 9
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

10 Installation OCTOPUS OS3
Release 01 02/2019
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available on the Internet at https://
www.doc.hirschmann.com/ as downloads:
User Manual Installation
User Manual Basic Configuration
User Manual Redundancy Configuration
Reference Manual Graphical User Interface
Reference Manual Command Line Interface

Installation OCTOPUS OS3
Release 01 02/2019 11
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

12 Installation OCTOPUS OS3
Release 01 02/2019
1 Description
1.1 General device description
The device is designed for the special requirements of industrial automation.
The device meets the relevant industry standards, provides very high
operational reliability, even under extreme conditions, and also long-term
reliability and flexibility.
The devices allow you to set up switched industrial Ethernet networks that
conform to the IEEE 802.3 standard.
The devices work without a fan.
The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. You find these manuals as PDF
files on the Internet at: https://www.doc.hirschmann.com
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
The Network Management Software Industrial HiVision provides you with
options for smooth configuration and monitoring. You find further information
on the Internet at the Hirschmann product pages: http://
www.hirschmann.com/en/QR/INET-Industrial-HiVision
There are convenient options for managing the device. Manage your devices
via:
Network management software (for example Industrial HiVision)
Web browser
V.24 interface (locally on the device)
SSH
Telnet
1.2 Device name and product code
The product code is made up of characteristics with defined positions. The
characteristic values stand for specific product properties.
Item Characteristic Characteri
stic value
Description
1 ... 3 Product OCTOPUS
OS3
OCTOPUS 24GE-HV-Trainrouter
4 (hyphen) -
Table 1: Device name and product code

Installation OCTOPUS OS3
Release 01 02/2019 13
5 Data rate 4 10a/100/1000 Mbit/s
6 Hardware type 0 Standard
7 (hyphen) -
8 ... 9 Number:
PoE ports
PoE(+) ports
00 0 ×
10 ... 11 Number:
10a/100 Mbit/s PoE/
PoE+ ports
00 0 × 10a/100 Mbit/s PoE/PoE+ ports
12 ... 13 Number:
10a/100/1000 Mbit/s
PoE/PoE+ ports
00 0 × 10a/100/1000 Mbit/s PoE/PoE+ ports
14 ... 15 Number:
10a/100 Mbit/s ports
00 0 × 10a/100 Mbit/s ports
16 ... 17 Number:
10a/100/1000 Mbit/s
ports
24 24 × 10a/100/1000 Mbit/s ports
18 ... 19 Number:
Ports >1000 Mbit/s
00 0 × 10000 Mbit/s ports
20 ... 21 First uplink port pair T6 Standard
22 ... 23 Second uplink port
pair
T6 Standard
24 (hyphen) -
25 Temperature range T Extended -40 °F ... +158 °F (-
40 °C ... +70 °C)
26 ... 27 Supply voltage N9 Rated voltage 72 V DC ... 110 V DC
Rated voltage range 50.4 V DC ... 138 V DC
Connection type 5-pin M12 connector
28 ... 29 Certificates and
declarations
S9 Z9 + EN 50121-4 + EN 50155
30 ... 31 Software packages MR Unicast + Multicast Routing
32 ... 33 Customer-specific
version
HH Hirschmann standard
34 Hardware
configuration
S Standard
35 Software configuration E Entry (Hirschmann Standard)
36 ... 37 Software level 3A HiOS Layer 3 Advanced
38 ... 42 Software version 07.5. Software version 07.5.
XX.X Current software version
43 ... 44 Maintenance version XX Current maintenance version
45 ... 47 Place of manufacture -NT Manufactured in Germany
a. Exclusively for twisted pair connections.
Item Characteristic Characteri
stic value
Description
Table 1: Device name and product code

14 Installation OCTOPUS OS3
Release 01 02/2019
1.3 Device views
1.3.1 Front view
1 V.24 interface 4-pin, “A”-coded M12 socket
2 USB interface 5-pin, “A”-coded M12 socket
3 Signal contact 5-pin, “A”-coded M12 plug
4 Supply voltage connection 5-pin, “K”-coded M12 plug
5 24 × 10/100/1000 Mbit/s twisted pair port 8-pin, “X”-coded M12 socket
6 LED display elements for port status
7 Slot hole for mounting on a flat surface
8 LED display elements for device status
9 Ground connection
Table 2: Front view (using the example OCTOPUS3-40-...)
1 2 3 4 5 6
9
8 7

Installation OCTOPUS OS3
Release 01 02/2019 15
1.4 Power supply
1.4.1 Supply voltage with the characteristic value N9
The power is supplied via a “K”-coded M12 plug.
For information about the position on the device see chapter “Device views”
on page 14.
Further information:
See “Device name and product code” on page 12.
1.5 Ethernet ports
You have the option to connect end devices or other segments to the ports
of the device via twisted pair cables.
You find information on pin assignments for making patch cables here:
“Pin assignments” on page 16
10/100/1000 Mbit/s twisted pair port
This port is an 8-pin, “X”-coded M12 socket.
The 10/100/1000 Mbit/s twisted pair port allows you to connect network
components according to the IEEE 802.3 10BASE-T/100BASE-TX/
1000BASE-T standard.
This port supports:
10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
1000 Mbit/s full duplex
Autocrossing (if autonegotiation is activated)
Autonegotiation
Autopolarity
The port casing is electrically connected to the front panel.
The pin assignment corresponds to MDI-X.

16 Installation OCTOPUS OS3
Release 01 02/2019
1.6 Pin assignments
Figure 1: Pin assignments: Interfaces and ports
Pin
1 TX
2 RX
3 -
4 GND
Function
12
3
4
V24
1 Uin
2 -
3 D -
4 GND
5 D+
Pin Function
12
3
4
5
ACA
FunctionPin
1 P+
2
3 P -
4
5 PE
Do not use
Do not use
1
2
3
4
5
Power
1
2
3
4
5
Signal
FunctionPin
1 Bl_DB+
2 Bl_DB -
3 Bl_DA+
4 Bl_DA -
5 Bl_DC+
6 Bl_DC -
7 Bl_DD -
8 Bl_DD+
1
2
7
4
3
5
6
8
Port GE
FunctionPin
1 -
2
3
4 -
5

Installation OCTOPUS OS3
Release 01 02/2019 17
1.7 Display elements
After the supply voltage is set up, the Software starts and initializes the
device. Afterwards, the device performs a self-test. During this process,
various LEDs light up.
1.7.1 Device state
These LEDs provide information about conditions which affect the operation
of the whole device.
Figure 2: Device status: location of the display elements on the device (front side of
the device)
LED Display Color Activity Meaning
Power Supply voltage — none Supply voltage is too low
yellow lights up Device variants with redundant power
supply:
Supply voltage 1 or 2 is on
flashes 4 times
a period
Software update is running. Maintain the
power supply.
green lights up Device variants with redundant power
supply:
Supply voltage 1 and 2 is on
Device variants with single power supply:
Supply voltage is on
Table 3: Device Status
Status
RM
Power
ACA

18 Installation OCTOPUS OS3
Release 01 02/2019
Status Device Status — none Device is starting and/or is not ready for
operation.
green lights up Device is ready for operation.
Characteristics can be configured
red lights up Device is ready for operation.
Device has detected at least one error in the
monitoring results
flashes 1 time
a period
The boot parameters used when the device
has been started differ from the boot
parameters saved.
Start the device again.
flashes 4 times
a period
Device has detected a multiple IP address
RM Ring Manager — none No redundancy configured
green lights up Redundancy exists
flashes 1 time
a period
Device is reporting an incorrect
configuration of the RM function
yellow lights up No redundancy exists
ACA Storage medium
ACA
— none ACA storage medium not connected
green lights up ACA storage medium connected
flashes 3 times
a period
Device writes to/reads from the storage
medium
yellow lights up ACA storage medium inoperative
LED Display Color Activity Meaning
Table 3: Device Status

Installation OCTOPUS OS3
Release 01 02/2019 19
1.7.2 Port Status
Note: In the present hardware version, the right side port LEDs of the M12
ports are without function. The port status is displayed via the left side port
LED.
Figure 3: Port status: location of the display elements on the device (front side of
the device)
LED Display Color Activity Meaning
L/D Link status — none Device detects an invalid or missing link
green lights up Device detects a valid link
flashes 1
time a period
Port is switched to stand-by
flashes 3
times a
period
Port is switched off
yellow lights up Device detects a non-supported SFP transceiver or
a non-supported data rate
flashing Device is transmitting and/or receiving data
flashes 1
time a period
Device detects at least one unauthorized MAC
address (Port Security Violation)
Table 4: Port status

20 Installation OCTOPUS OS3
Release 01 02/2019
1.8 Management interfaces
1.8.1 V.24 interface (external management)
This interface is a 4-pin, “A”-coded M12 socket.
The V.24 interface is a serial interface for the local connection of an external
management station (VT100 terminal or PC with corresponding terminal
emulation). This allows you to set up a connection to the Command Line
Interface (CLI) and to the system monitor.
The socket housing is electrically connected to the front panel of the device.
The V.24 interface is electrically insulated from the supply voltage.
1.8.2 USB interface
This interface is a 5-pin, “A”-coded M12 socket with shielding.
The USB interface allows you to connect the AutoConfiguration Adapter
ACA21-M12/ACA22-M12 storage medium. This is used for saving/loading
the configuration data and diagnostic information, and for loading the
software.
The USB interface has the following properties:
Supplies current of max. 500 mA
Voltage not potential-separated
Supports the USB master mode
Supports USB 2.0
VT100 terminal settings
Speed 9600 Baud
Data 8 bit
Stopbit 1 bit
Handshake off
Parity none