Hisense RT32D6ASE User manual

Owner’ s manual
Compact Double Door Refrigerator
Model:RT32D6ASE
RT32D6ABE

© 2015 Hisense Company Ltd. All Rights Reserved.
All material in this Owner's Manual is the property of Hisense
Company Ltd. and its subsidiaries, and is protected under US and
in any manner, electronic, print, or otherwise, without the prior
or distributed, in whole or in part, in any manner, electronic or
Requests for permission to store, reproduce, transmit or distribute
materials may be made to the following address:
PO Box 3289
Suwanee, GA 30024
Hisense, and any and all other Hisense product names, logos, slogans
or marks are registered trademarks of Hisense Company Ltd. and its
holders.
COPYRIGHT STATEMENT

appliance, unless they are of the type recommended by the manufacturer.
21. WARNING: Do not use electrical appliances inside the food storage compartments of the
20. WARNING: Do not damage the refrigerant circuit.
clear of obstruction.
19. WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure,

Do not use extension cords or ungrounded(two
prong) adapters.

The side at which the door opens can be
changed from the right side (as supplied) to
the left side, if the installation site requires.
Tools you will need:
.8mm socket driver
.cross-shaped screwdriver
Note: Before this step, you should lay the refrigerator
on it’s back in order to gain access to the base, you
should rest it on soft foam packaging or similar
material to avoid damaging the cooling pipes at the
rear of the refrigerator.
.Putty knife or thin-blade screwdriver
2. open the screw hole cove and the upper
hinge cover which is at the top right corner of
the refrigerator. upper hinge
cover (right)
1. Stand the refrigerator, open the upper
door and remove the things in the door and
close it.
3.Unscrew the special flange self-tapping
screws which are used for fixing the right
upper hinge part by a 8mm socket driver
or a spanner(please support the upper
door with your hand when doing it ).
right upper hinge part
special flange
selftapping screws
5.Remove upper door and place it on
smooth surface with panel upwards.
6. Loose screws used to fix middle hinge
and remove middle hinge. Then turn middle
hinge by 180. Take washer on axis and put
it on another end. Place it well for use.
7. Remove lower door and place panel
upwards on smooth surface.
8. Change screw hole covers on middle
cover plate from left to right (as shown in
figure below).
Front foot fixed board
Self tapping screws
Adjustable bottom feet part
Lower hinge partΰrightα
4.Remove the right upper hinge part and
, thescrew hole cover place them on
smooth surface.
screw hole cover
.7mm wrench
Caution㧦
To avoid to injury yourself and/or property,
we recommend someone assist you during
the door reversal process.
.Ensure the Appliance is unplugged and
empty.
.Following steps are generally
recommended
Changing the door from the right side to the left.

10. Change lower hinge part to left and front
foot fixed board to right and fix them with
screws. Then install adjustable bottom feet
parts.
Lower hinge part (left)
11. move lower
door and adjust its position to align lower
hole(left) site and lower hinge axis. Then
adjust middle hinge and align the middle
hinge axis to the higher (left) hole site. Then
install the middle hinge.
Stand the refrigerator then
Note: washer may
stick to lower door. Washer
13. Replace and the right upper hinge Install
cover on the left corner, Replace the screw
hole cover on the right corner.
14.Stand and level the appliance.
NOTE:
Before the appliance is powered, We
recommend that you should wait for about
.
2 hours