Hitachi CM-N38000BF User manual

9XYZ4(KW)EDCBA62010031CM-N38000BF
Made in Japan
HITACHIIon cleansing with moisturizing support device
ֵ⭞䃠᱄ᴮ
INSTRUCTIONS
ᰛ㄁ⓡ⟧ߦ㛂䴘ᆆ␻▊ؓ☋ಞ
֒ᇬቻ⭞䙊
For household use only
: 100-240V
Ӛ⍷ᕅ
AC 日本製造

English Page 1~16
17~31
ѣᮽ

㻯㻹㻙㻺㻟㻤㻜㻜㻜㻮㻲 12345671112138▼▼910

-1--2-Safety precautions
Precautions described here are intended for safe and correct use of this product and are
to prevent injury and damage to you and others before they occur.
Precautions are classified as follows.
Make sure to observe the precautions because they are all important in relation to safety.
●●
<Examples of pictorial indication>
The symbol indicates "Compulsory" (Make sure to do this).
"Disassembly prohibited""Use prohibited in wet areas"
"Use with wet hands prohibited"
"General action" "Unplug"
English
Indicates a dangerous situation in which improper handling
could result in death or serious injury to a user.
Indicates a dangerous situation in which improper handling
could result in slight injury to a user or damage to property
(house, household effects, etc.).
Indicates an imminently dangerous situation in which improper
handling may result in death or serious injury to a user.
The symbol indicates "Prohibited" (Do not do this).
Persons who use the following medical electronic devices should not use this
product. (This product may cause the medical electronic devices to malfunction.)
- Self-contained medical electronic devices such as a pacemaker
- Wearable medical electronic devices such as an electrocardiograph
Prohibited
Do not use this product by other methods which are not described in this
instruction manual. (Cause of accident, trouble, or failure)
Prohibited
Use this product only for face and neck. (Cause of an accident or trouble)
Prohibited
Prohibited
Do not use this product on the following regions.
(Cause of accident or trouble)
- Regions where orthopedic treatment was given - Eyeballs and upper eyelids
- Wound sites - Facial melanoderma - Mucosal regions, such as inside the mouth
- Regions irritated due to pimples or skin rash -Lips
- Regions which suffer from sensation of pain or perception disorder
- Regions where metal, plastic or silicone etc., is embedded under skin
- Regions where there is itching, sensation of warmth, or liver spots due to physical stimulus etc.
- Regions where skin irritation is caused by cosmetics
Children should be supervised to ensure that they do not play with
the appliance.
When feeling pain or disorder during use of this product, or sensing anything
wrong with your skin after use, stop using this product and consult a
dermatologist. (Cause of skin trouble etc.)
Unplug
Make sure
If any abnormality occurs during use, immediately pull out the power plug of
the power adaptor from the outlet. (Cause of accident or fire)
Use only 100-240V AC for power supply. (Cause of fire or electric shock)
Do not use if the power cord or the power plug is damaged or its insertion to
the outlet is loose. ( If the power cord breaks, a fire or electric shock may occur.)
The power cord cannot be unnecessarily bended, pulled, twisted, bound,
placed a heavy object on it, pinched, processed, or wound around the power
adaptor. (If the power cord damages fire or electric shock may occur.)
Make sure
If any unusual sound or abnormality occurs in the main body, immediately
stop using this product and contact the distributor for repair together with the
power adaptor. (Cause of accident or trouble)
Persons who use this product for the first time should use it while observing
the condition of their skin. (Cause of skin trouble or poor physical condition)
The following persons should be avoid to use this product.
(Cause of an accident or trouble)
- Persons with heart disease - Persons with an acute (pain) illness
- Persons with fever - Persons with a blood pressure disorder
- Persons with an infectious disease - Persons with a tubercular disease
- Persons with a malignant tumor - Persons with facial neuralgia
- Persons who are pregnant - Persons who are menstruating
- Persons with atopic dermatitis - Persons with an allergic predisposition
- Persons with particularly sensitive skin - Persons with hemophilia
- Persons under dental care
- Persons whose blood vessels have expanded due to long time use of steroid
hormones or liver function disorder
- Persons who are under the influence of alcohol or medication, or who are very tired
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Use the COOL mode at an ambient temperature in the range of 10 to 40℃.(Cause of skin damage as the head is too cold if the device is used at a low
temperature)
Do not use this product near inflammable substances (gasoline, benzene,
thinner, etc.). (Cause of explosion or fire)
Person who uses this device for the first time should use this while observing
the condition of their skin. (Cause of skin trouble and poor physical condition)
Do not use this product beyond the specified operating time.
(Cause of skin trouble)
Do not insert or remove the power plug in/from the outlet with wet hands.
(Cause of failure or short circuit)
Use with wet
hands prohibited

-3--4-Level indicator lamp
LOW (green): MEDIUM (green): HIGH (red)
When the power switch is switched to “On,”
the lamp indicating “Low” is turned on. This
lamp is not turned on in “Cool” mode.
Level switch button
Every time the button is pressed, "the
strength" of the electrical potential will
change. There will be no change in
vibration strength. (“Low” is initially set.)
Body socket
Stand
Instrument plug
Cord
Accessories
Rings (two) : Rings for attaching cotton.
Unplug
Check the head for any damage or deformation before use.
(Cause of damage to skin)
Do not use this product together with other beauty treatment devices at the
same time. (Cause of failure or trouble)
Prohibited
Use only the original power adaptor. And, do not use any other product
with the original power adaptor. (Possibility of electric shock or ignition)
Do not use this product if there is some injury or wound to your skin.
(Cause of skin trouble or pain)
Do not drop this product or give it a strong impact.
(Cause of injury or failure)
Do not wipe with benzene, thinner or alcohol, and do not spray insecticide.
(Cause of cracking, electric shock, or ignition)
Make sure
Remove accessories such as earrings and necklaces, and contact lenses
before use. (Cause of accident or trouble)
If there is any severe skin disorder or irregularity on your skin surface, or due
to downy hair, you may feel strong irritation in rare instances. In this case,
avoid using this product on that region. (Cause of accident or trouble)
Do not keep the cotton puff or the head on one part of your skin but always
keep it in motion. (Cause of skin trouble or poor physical condition)
Do not hold the cord to pull out the power plug and device plug.
(Cause of disconnection, electric shock, short circuit, or ignition)
Make sure to pull out the power plug from the outlet while not in use.
(Cause of electric shock or fire by deterioration)
Names of parts and their functions (Fig. 1)
Body
Do not alter disassemble or repair by unauthorized techinician.
(Cause of fire, electric shock, injury, or failure)
Preparation before use
Do not leave this product in a place where the temperature becomes high
such as the inside of a vehicle. (Cause of failure)
When there are people around the device, pay attention to any sudden
movement during use. (Cause of injury)
Heating head (titanium material)
Attach cotton and apply it to your skin.
The device vibrates while being used in
modes other than “Cool.”
Mode indicator lamp
Mode switch button
Every time the button is pressed, the
mode for use will be switched.
(“HOT CLEANSING” is initially set.)
Power switch (" ")
Turn on the power switch, and it will turn
"On." Press it again, and it will turn "Off."
An automatic shutoff function is equipped,
so if the device is not used for around 3
minutes, it will automatically turn "Off."
Buzzer (Switching sound/ready
sound/warning sound/finish sound/indicating timer sound)
Every time the switch or button is
pressed, the switching sound will beep.
When the preparation is completed in
“Cool” mode, the ready sound will beep.
The warning sound will beep to indicate
the continuous use of “Cool” mode.
In the event of a failure, an abnormality
detection sound will beep. When each
mode is finished, the finish sound will
beep.
Power adaptor
Model: KH-186B
Power plug
Cooling head (aluminum material)
Apply this head to your skin in “Cool”
mode.
Back plate (titanium material)
Touch this part and apply the heating
head to your skin in modes other than
“Cool,” and the device will start to
operate.
Mode During preparation
Orange lamp
flashing
Orange lamp
lights
HOT MASK
COOL
Blue lamp flashing
During use
Blue lamp lights
Never use the device when you have a wound or an inflammation on
your skin. (Cause of problems with or damage to your skin.)
Remove jewelry or contact lenses.
(Cause of problems with your skin or physical discomfort.)
1. About mode switching
Mode Materials needed
HOT CLEANSING (cleans fine residue
remaining in pores)
HOT MASK (enhances the effect of
milky lotion or sheet mask)
Use your regular milky lotion or a sheet mask by
applying to skin. Do not use cotton.
Use new cotton saturated with your regular
toner.
HOT MOISTURIZE
(performs
moisturizing care by allowing moisturizing
ingredients to penetrate into skin)
Use new cotton saturated with your regular toner.
If you use a gel-like or thick toner, you can also
apply it to heating head without using cotton.
COOL (tightens the pores of your skin
by cooling effect)
Apply the cooling head directly to your skin.
Do not use cotton and toner.
Do not wash or splash water on this product.
(Cause of failure or short circuit)
Do not use or keep this product in places easily splashed with water or in
damp places, such as in a bathroom. (Cause of failure or short circuit)
HOT CLEANSING
HOT MOISTURIZE
Disassembly
prohibited
Use prohibited
in wet areas
This mark means that this appliance shall not be used near water contained
in bath-tubs, basins or other vessels.

-5--6-●●●(
HOT CLEANSING )
(HOT
MOISTURIZE )
Automatic shutoff
Automatic shutoff
approximate 3 minutes
approximate 3 minutes
2 Clean skin by washing your face so that makeup and dirt will wash off.
Wipe off makeup with a cleansing product.
3 Attach cotton to the body of the device. (Fig.2)
(1)Remove the protection seal from the heating head.
Unless the protection seal is removed, the device will not operate.
(2)Place cotton over the head and attach it with the included ring.
Use commercially available cotton. However, small cotton or thick cotton may not
work in some cases.
The ring has an orientation with a clear direction. Attach it from straight above with the
wider part of the inner circumference placed toward the heating head.
Basic mode
Step 1
Step 2
Step 4
Step 3
●●(2) Use the device on bare skin after removing makeup.
(3) Do not use the device on the same area of skin for more than 10 seconds.
(4) Switch between high and low by pressing the level switch button according to the
condition of your skin.
Example for use
Step 2 "HOT MOISTURIZE "
When you do not have much time in the morning or when you need to go out suddenly,
you can just use “HOT MOISTURIZE .” It only takes approximate three minutes to
moisturize your skin thoroughly. Press the mode switch button to set to
“HOT MOISTURIZE .”
●●●●Quick treatment (Required time: approximate 3 minutes)
Press the mode switch button and set the mode of your preferred treatment.
Quick tighten-up treatment (Required time: approximate 2 minutes)
Step 4 “COOL”
When you want to tighten your pores or cool down your skin before applying make up,
you can just use “
COOL .”After 10-second preparation for cooling, it only takes
approximate one minute and 50 seconds to tighten the pores of your skin.Press the
mode switch button to set to “
COOL .”
Tighten-up treatment (Required time: approximate 5 minutes)
Step 1 “HOT CLEANSING”
Step 4 “COOL”
When you want to remove fine residue remaining in pores and tighten the pores of your
skin, use “ COOL ” after using “ HOT CLEANSING .” This treatment cleanses and
tightens the pores of your skin. After the “ HOT CLEANSING ” mode is finished, press
the mode switch button to set to “
COOL .”
Step 1 "HOT CLEANSING "
Step 2 "HOT MOISTURIZE "
Step 4 “COOL”
Standard daily moisturize treatment
After using “HOT CLEANSING ,” moisturize the clean skin in “HOT MOISTURIZE and
tighten the pores of your skin by cooling effect in “COOL.” After the “HOT MOISTURIZE ”
mode is finished, press the mode switch button to set to “COOL.”
●●●Daily treatment
(Basic mode) (Required time: approximate 8 minutes)
●●●●Recommended full treatment (Required time: approximate 11 minutes)
Step 1 “HOT CLEANSING”
Step 2 "HOT MOISTURIZE "
Step 3 “HOT MASK”
Step 4 “COOL”
Care for your skin once or twice a week by using all modes.
Fine vibrations in “ HOT MASK ” mode and gentle switching of the electrode will enhance
the moisturizing effect of lotion or mask. The cooling effect of “COOL” mode will tighten
the pores of your skin.
Step 1 "HOT CLEANSING "
Step 2 "HOT MOISTURIZE "
Before you go out or when you have more time, use “HOT MOISTURIZE ” after using
“HOT CLEANSING .” This treatment moisturizes the clean skin thoroughly.
●●Moisturize treatment (Required time: approximate 6 minutes)
Do not attach the ring in the reverse direction. Please be careful not to squeeze it,
otherwise, it cannot be removed.
The narrower side should be upward. Cotton
4 How to remove the ring. (Fig.3)
Remove the ring by pulling it straight up while holding down the lower part.
5 Please observe the following so as not to damage your skin when you use the device.
(1) The maximum amount of time allowed for skin care with use of this device is 8
minutes per day in basic mode. (Limit use of step 1,2,3 to no more than 3 minutes
per day. Limit use of step 4 to no more than once a day.)
（ HOT MASK ）（
COOL ）approximate 3 minutes
(Preparation for cooling：approximate 10 seconds)
(Time for use: approximate 1 minute and 50 seconds)
Automatic shutoff
Automatic shutoff
You can choose high, medium and low as you like.
If your skin tingles, use the device on "Low."
If you feel something unusual with your skin, stop using the device and consult a
skin care specialist.
Limit use of the device to no more than 11 minutes per day including use of
“
HOT MASK .”
It is recommended that you use “
HOT MASK ” once a day for milky lotion or once
or twice a week for sheet mask.
●●
How to use
●●Make sure to use only 100-240V AC for power supply and use the included power
adaptor (this device is not rechargeable).
After the power switch is switched to “On,” the heating head warms slowly.

-7--8-2 After confirming that the power adaptor is connected to the main body, press the power
switch. (Fig. 4)
3 Choose "the strength" of electrical potential with the level switch button.
Switch the "strength" with the level switch button according to the condition of your skin.
●●The level indicator lamp will be turned on, and “HOT CLEANSING” on the mode
indicator lamp will start flashing. If a lamp in another mode is flashing, press the mode
switch button to switch to “HOT CLEANSING.”
Every time the level indicator button is pressed, the “LOW”,”MEDIUM” and “HIGH” of
the electrical potential will be switched.
There will be no change in vibration strength.
●Make sure to hold the body with your hand touching the back plate.
●●●5 Apply cotton to the skin and move the device slowly.
(Fig. 6)
●Apply cotton gently to the face and slowly move the device by sliding it from the
center of the face to the outer side.
The mode indicator lamp will turn on and the device will start to vibrate.
The time for use is within approximate 3 minutes.
Unless you apply the cotton to your skin while touching the back plate, the device
will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
4 Hold the device with your hand touching the back plate of the body.
(Fig. 5)
●●●
CAUTION
Step 1 "HOT CLEANSING "
This mode removes fine residue remaining in pores which cannot be removed by simple
washing.
1 Saturate cotton attached to the body with toner after washing your face.
Please use your regular toner or rubbing-off toner with an exfoliating effect.
(Do not use milky lotion or a gel-like or thick toner.)
Saturate the cotton with toner to the extent that toner permeates the back of the
cotton.
●8 Remove the ring and the cotton.
6 After 3 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
The finishing sound (beep beep) will inform you.
●●Wipe off the surface of the heating head with a tissue.
Do not use the cotton again once it is used. It might cause problems with your skin.
●●1 Attach new cotton to the body with the attachment ring.
Step 2 " HOT MOISTURIZE "
7 After use, make sure to pull out the power adaptor from the electric outlet and the
main body.
(Fig. 7)
To continue to use the next mode, do not disconnect the power adaptor.
Pull out holding the plug portion.
●●Do not use milky lotion or a gel-like or thick toner.
Saturate the cotton with lotion to the extent that lotion permeates the back of the
cotton.
2 Saturate the cotton with your regular toner.
3 After confirming that the power adaptor is connected to the main body, press the
power switch.
(Fig. 8)
●“Low” on the level indicator lamp lights and “
HOT MOISTURIZE ” on the mode
indicator lamp starts flashing. If a lamp in another mode is flashing, press the mode
switch button to switch to “ HOT MOISTURIZE .”
Every time the level indicator button is pressed, the “LOW”,”MEDIUM” and “HIGH”
of the electrical potential will be switched. There will be no change in vibration
strength.
●4 Choose "the strength" of electrical potential with the Level switch button. Switch the
"strength" with the Level switch button according to the condition of your skin.
Do not use the product around eyes and ears.
(Cause of accidents or bad physical condition)
If you feel something is unusual with your skin or body while using the
device, stop using it immediately and consult a skin care specialist.
(Cause of accident or poor health)
Some toner (just with mineral spring or water) may be difficult to bring out a
good effect.
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "LOW."
Add more toner when there is no moisture in the cotton or when the device is
difficult to slide.
Do not apply the device on the same area of skin for more than 10 seconds.
If you feel your skin tingling by micro current while using the device, press the level
switch button and switch to "Low."
If you still feel your skin tingling, use the device by adding more toner.
When the "HOT
CLEANSING " mode is finished, press the power switch and the
" HOT MOISTURIZE " mode will automatically be set.
This mode cares for skin by allowing moisturizing ingredients of toner permeate into
the skin.
When using cotton
For attaching a cotton puff, see "Preparation before use."
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "LOW."
5 Hold the device with your hand touching the back plate of the body. (Fig. 5)
●Make sure to hold the body with your hand touching the back plate.
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②%RWKFKHHNVĺ③T-zone
ĺ④décolletage, the whole area can be efficiently and uniformly cared for.
Indicating timer function
Do not keep the cotton on the same area of skin, it is necessary to
move it around.
(Cause of problems with your skin or physical discomfort.)

-9--10-8 After use, make sure to pull out the power adaptor from the electric outlet and the
main body. (Fig. 7)
To continue to use the next mode, do not disconnect the power adaptor. ●●3 Choose "the strength" of electrical potential with the level switch button.
Switch the "strength" with the Level switch button according to the condition of your skin.
Every time the level indicator button is pressed, the high, medium, and low of the
electrical potential will be switched. There will be no change in vibration strength.
●“Low” on the level indicator lamp lights and “
HOT MOISTURIZE ” on the mode
indicator lamp starts flashing. If a lamp in another mode is flashing, press the mode
switch button to switch to “ HOT MOISTURIZE .”
2 After confirming that the power adaptor is connected to the main body, press the power
switch. (Fig.8)
When the " HOT CLEANSING " mode is finished, press the power switch and the
" HOT MOISTURIZE " mode will automatically be set.
●The mode indicator lamp will switch and turn on, and the device will start to vibrate.
The time for use is within 3 minutes.
●●●●Add more toner or moisturizing product when the heating head does not easily slide.
Apply the heating head gently to the face and slowly move the device by sliding it
from the center of the face to the outer side.
Unless you apply the heating head to your skin while touching the back plate,
the device will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
5 Apply the heating head directly to the skin and move it slowly.
(Fig. 6)
●Do not apply the device on the same area of skin for more than 10 seconds.
If you feel your skin tingling by micro current while using the device, press the
Level switch button and switch to "LOW." If you still feel your skin tingling, use the
device by adding more toner or other cosmetics.
●
CAUTION
8 Wipe off the moisturizing product on the heating head and the body of the device with a
tissue.
6 After 3 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
The finish sound (beep beep) will inform you.
●●To continue to use the next mode, do not disconnect the power adaptor.
4 Hold the device with your hand touching the back plate of the body.
(Fig. 5)
●Make sure to hold the body with your hand touching the back plate.
7 After 3 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
The finish sound (beep beep) will inform you.
7 After use, make sure to pull out the power adaptor from the electric outlet and the
main body.
(Fig. 7)
Unless you apply cotton puff to your skin while touching the back plate, the device
will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
CAUTION
Apply the cotton gently to the face and slowly move the device by sliding it from the
center of the face to the outer side.
Do not keep the cotton on the same area of skin, it is necessary to
move it around.
(Cause of problems with your skin or physical discomfort.)
Add more toner when there is no moisture in the cotton or when the device is
difficult to slide.
Do not apply the device on the same area of skin for more than 10 seconds.
If you feel your skin tingling by micro current while using the device, press the Level
switch button and switch to "Low."
If you still feel your skin tingling, use the device by adding more toner.
●●●●9 Remove the ring and the cotton.
Wipe off the surface of the head with a tissue.
Do not use the cotton again once it is used. It might cause problems with your skin.
●●When not using cotton
If you use a gel-like toner/moisturizing product (all-in-one type toner for moisturizing) or
thick toner which is difficult to permeate the cotton you can use this device without attaching
cotton to the body.
1 Apply a gel-like moisturizing product or thick toner that you would normally use onto the
heating head and smoothen it over the entire head with your fingers.
(Fig. 9)
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "Low."
Moisturizing product
Do not keep the heating head on the same area of skin, it is
necessary to move it around.
(Cause of problems with your skin or physical discomfort.)
●6 Apply cotton to the skin and move the device slowly.
(Fig. 6)
The mode indicator lamp will turn on and the device will start to vibrate.
The time for use is within 3 minutes.
●
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②%RWKFKHHNVĺ③T-zone
ĺ④décolletage, the whole area can be efficiently and uniformly cared for.
Indicating timer function
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②%RWKFKHHNVĺ③T-zone
ĺ④décolletage, the whole area can be efficiently and uniformly cared for.
Indicating timer function

-11--12-●3 Choose "the strength" of electrical potential with the level switch button.
Switch the "strength" with the Level switch button according to the condition of your
skin.
Every time the level indicator button is pressed, the high, medium, and low of the
electrical potential will be switched. There will be no change in vibration strength.
●●●●●●●4 Hold the device with your hand touching the back plate of the body.
(Fig.5)
Make sure to hold the body with your hand touching the back plate.
5 Apply and move the heating head slowly.
(Fig.6)
When using a sheet mask, slide the head over the sheet mask.
The mode indicator lamp will switch and turn on, and the device will start to vibrate.
The time for use is within 3 minutes.
Unless you apply the heating head to your skin while touching the back plate, the
device will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
CAUTION
7 After use, make sure to pull out the power adaptor from the electric outlet and the main
body. (Fig.7)
To continue to use the next mode, do not disconnect the power adaptor.
8 Wipe off the lotion on the heating head and the body of the device with a tissue.
●●It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "Low."
Step 4 “COOL”
In this mode, the cooling head surface that is cooled about 10℃below the ambient
temperature tightens the pores of your skin.
1 After confirming that the power adaptor is connected to the main body, press the power
switch. (Fig.11)
The level indicator lamp will go out, and “COOL” on the mode indicator lamp starts
flashing. If a lamp in another mode is flashing, press the mode switch button to
switch to “COOL.”
When the " HOT MASK " mode is finished, press the power switch and the " COOL "
mode will automatically be set.
Use this device at an ambient temperature from 10 to 40℃. (If you
use “COOL” mode at low temperature, the head may be overcooled,
damaging the skin.)
CAUTION
Continuous use of the “COOL” mode makes it difficult to cool the cooling head.
The warning sound (beep beep) and the flashing “COOL” on the mode indicator lamp
will inform you.3 Apply the cooling head gently to your skin and move it slowly just like patting your face.
(Fig.12)
The mode indicator lamp will change to lighting from flashing.
The cooling head does not vibrate.
The time for use is within one minute and 50 seconds.
Since you can apply the device to the same area of your skin for only one second,
repeatedly apply the head to your skin on and off towards the face.
There is no indicating timer function in the “COOL” mode.
2 Wait until the cooling head has cooled.
Preparation for cooling takes about 10 seconds. “COOL” on the mode indicator lamp
flashes during preparation.
When the device is ready for use, the ready sound will beep, and the mode indicator
lamp will be turned on.
●●●●●●The device does not vibrate in “COOL” mode.
CAUTION
●Apply the heating head gently to the face and slowly move the device by sliding it
from the center of the face to the outer side.
Step 3 “HOT MASK”
(It is recommended that you use “HOT MASK” once a day for milky lotion or once or twice
a week for sheet mask.)
Fine vibrations and gentle switching of the electrode enhance the effect of milky lotion or
sheet mask.
1 Place a sheet mask on your face or spread milky lotion or cream that you would
normally use over your entire face.
Wipe off any lotion on your hands.
2 After confirming that the power adaptor is connected to the main body, press the
power switch. (Fig.10)
“Low” on the level indicator lamp lights and “ HOT MASK ” on the mode indicator lamp
starts flashing. If a lamp in another mode is flashing, press the mode switch button
to switch to “ HOT MASK .”
●●When the "
HOT MOISTURIZE " mode is finished, press the power switch and the
" HOT MASK " mode will automatically be set.
Do not apply the device on the same area of skin for more than 10 seconds.
If you feel your skin tingling by micro current while using the device, press the Level
switch button and switch to "LOW."
6
After 3 minutes have elapsed, the device will automatically shut off. (Auto shutoff function)
The finish sound (beep beep) will inform you.
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②%RWKFKHHNVĺ③T-zone
ĺ④décolletage, the whole area can be efficiently and uniformly cared for.
Indicating timer function
Do not keep the heating head on the same area of skin, it is
necessary to move it around.
(Cause of problems with your skin or physical discomfort.)
Do not slide the cooling head over the skin.
Do not keep the cooling head in the same area of the skin, but move it around.
The cooling effect of the cooling head may be lessened.
CAUTION
●●

-13--14-●●●●Wipe off the toner on the head and the body with a tissue.
When dirt is difficult to remove, wipe it off with a cloth after saturating it with water and
wring it thoroughly.
Care for main body
★ Do not use alcohol, benzine, or thinner.
(Cause of deformation or discoloration)
CAUTION
How to preserve
★Do not leave in an area subject to direct sunlight (inside of a vehicle in
summer, etc.) or near heaters. (Cause of deformation or discoloration)
CAUTION
Disposal of the product
This product includes recyclable parts.
For disposal of the parts, observe your local laws and regulations etc.
Specifications
Do not disassemble except when disposing of the product.
Do not clean the main body with water. Or do not dip in water,
and do not pour water. (Cause of failure)
Make sure to pull out the power adaptor from the electric outlet.
(Improperly turning on the switch may give a tingling sensation or
result in malfunction or short-circuit.)
Store the device on the included stand in a place free from excessive humidity or dirt.
The stand can store the rings in it as well as put the body on it. (Fig.13)
Do not leave in a water splashing area or an area with significant
humidity, such as a bath. (Cause of short-circuits or failure)
Do not wind the power cord around the power adaptor or the main
body. (Cause of damage to cord)
4 After one minute and 50 seconds have elapsed, the device will be automatically shut off.
(Automatic shutoff function)
The finish sound (beep beep) will inform you.
When the “COOL” mode is finished, the main body and the cooling head become
slightly hot, however this is not unusual.
5 After use, make sure to pull out the power adaptor from the electric outlet and the main
body.
(Fig.7)
If a toner/moisturizing product remaining on the skin attaches to the cooling head or
the main body, please wipe off with a tissue.
The power adaptor may become slightly hot during use, however this is not a device
failure.
●●●●
CAUTION
If all of the mode indicator lamp and the level indicator lamp start flashing and the
abnormality detection sound beeps during use, this is a warning of device failure.
Pull out the power adaptor from the electric outlet, and contact the distributor for
repair.
About skin sensing function
This device is a product which operates through the human body. Applying the skin to
the back plate and the head will make an electrical circuit start to operate.
Unless you touch the back plate and apply the head to the skin, it will not start to operate.
●
Rings (two), Stand
Accessories
Around 11 minutes at the maximum
Operating time
Main body : Approximately 150g
Power adaptor : Approximately 120g
Mass
100 - 240V AC, common to 50-60Hz
Rated voltage
14W(Power adaptor : KH-186B) Rated power input
Step 1.2.3 Approximate 4.3W (Room temperature 25 ℃)Step 4
(COOL) Approximate 13W (Room temperature 25 ℃)Power consumption
CAUTION
Make sure to pull out the device plug from the main body after using.
Do not store it when the power adaptor is connected with the main body or the cord is
wound around the main body. (Result in damage of the cord)
Cord
Do not wind the cord around
the main body.
Device plug.
※Make sure to pull out the device plug
from the main body after using.
(Make sure to holding the plug to pull
out from main body.)
Do not keep the device plug and cord in a state of bending.