Hitachi CP-WU9100 User manual

1
Projector
User's Manual - Network
Quick Setup Guide
Thank you for purchasing this product.
This manual is intended to explain only how to setup this product. For proper use
of this product, refer to this manual and the other manuals for this product.
CP-WU9100/CP-HD9950
Connecting the projector and the computer using the network, remote control and
status monitoring of the projector can be performed by Web browser.
Two types of interface, Projector Web Control and Crestron e-Control, are
available for this projector.
1.1 Web Control
Projector Web Control Crestron e-Control
1. Features
See the corresponding pages for quick setup.
・Connection Setup (&7)
・System Requirements for Applications (&13)

2
1.2 Network Presentation
The projector can display the computer screen images transmitted through the
network.
To use Network Presentation, an exclusive application, LiveViewer is required.
The following application is required to use Network Presentation.
OS Application
Windows®LiveViewer
Mac OSX LiveViewer
iOS(iPhone/iPad) Projector Quick Connection
Android Projector Quick Connection

3
1.3 My Image Function
The projector can display still images transferred using the network.
You can allocate up to four image les.
MY IMAGE transmission requires an exclusive application for your computer.
Use the application to transfer the image data.
1
43
2
1
43
2
1
43
2
Transfer image data
Display image data (ex. )

4
1.4 Messenger Function
The projector can display text data transferred using the network on the screen.
Up to 12 text data can be stored.
Transfer text data
Display text data (ex. )
1
43
2
1
4
3
2
12
1
4
3
2
12

5
1.5 Network Bridge Function
This projector is equipped with the NETWORK BRIDGE function to perform
mutual conversion of a network protocol and a serial interface.
By using the NETWORK BRIDGE function, a computer connected to the projector
using wireless or wired LAN can control an external device using
RS-232C communication using the projector as a network terminal.
1.6 Other Functions
The projector can automatically send an alert message to the specied using
addresses when the projector detects a certain condition requiring maintenance
or detected an error.
1.6.1 E-mail Alerts
The SNMP (Simple Network Management Protocol) manages the projector
information, which is a failure or warning status, from the computer on the
network. The SNMP management software is required on the computer to use
this function.
1.6.2 Projector Management using SNMP
RS-232C
RS-232C cable
External device
Wired LAN
LAN cable
Computer
Protocol change
TCP/IP data Serial data
WIRELESS port
(USB wireless adapter)
Wireless
LAN
CONTROL port
LAN port

6
The scheduling function sets up scheduled events including
power on / power off. It allows the projector to be self-managing.
The schedule can be set in Projector Web Control or OPTION-SCHEDULE menu
in the projector.
1.6.3 Event Scheduling
You can congure and control the projector using the network using RS-232C
commands.
1.6.4 Command Control using the Network
1) Press the MENU button on the remote control or the control panel of the projector.
2) From EASY MENU, select LANGUAGE.
Then, select your desired language.
2. Changing the Display Language
Follow the on-screen display (OSD) for proper operation.
MENU
button MENU button

7
3.1 Connection using Wired LAN
1) Connect the projector to the computer using a hub
with a LAN cable (CAT-5e or higher).
2) Press the MENU button on the remote control or the
control panel of the projector.
The MENU you last used will appear.
Use the cursor button to select the following.
EASY MENU > ADVANCED MENU > NETWORK > WIRED SETUP
3) Set the following items in WIRED SETUP.
・󲹭DHCP
・IP ADDRESS
・SUBNET MASK
・DEFAULT GATEWAY
・DNS SERVER
For setting an IP address, refer to About IP address. (&8)
Select APPLY, then press the ENTER button to apply the settings.
The connection using wired LAN is available. Set wired LAN for the projector by
following the instructions of your network administrator when connecting to the
existing network.
3. Connection Setup
Refer to System Requirements for Applications (&13) rst before setting up the
connection.
3.2 Connection setup of Wired LAN
hub

8
• Although HDBaseT™ and LAN port can be used for wired LAN, they
cannot be used simultaneously. Connect LAN cable to the port set in WIRED
NETWORK on NETWORK menu.
• The same network address cannot be used for both wireless LAN and wired LAN.
• I f the projector and the computer exist in the same network (such as, same
network address), leave the default gateway eld blank.
• When the projector and the computer exist in different networks, the default
gateway must be set. Consult with the network administrator in detail.
NOTE
[About IP address]
■ Setting manually
The Network address portion of the IP address setting on your computer must
be the same as the setting on the projector. Also, the entire IP address on the
computer must not overlap with that of the other devices on the same network,
including the projector.
The projector’s settings are as follows.
IP address: 192.168.1.254
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
Therefore, specify the computer’s IP address as follows.
IP address: 192.168.1.xxx (xxx shows decimal number.)
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)
For example
Select from 1 to 254 for “xxx” without duplicating any other equipment.
In this case, as the IP address of the projector is “192.168.1.254”, specify
a setting between 1 to 253 for the computer.
■ Setting automatically
When a DHCP server exists in the connected network, it assigns an IP address
to the projector and the computer automatically. If DHCP server is not available,
set IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY.

9
3.3 Connection using Wireless LAN
Connection using wireless LAN is available with option parts, USB wireless
adapter (USB-WL-11N).
Wireless LAN has two types of connection, Simple Access Point and
Infrastructure.
* Simple Access Point is a mode which connects to computers directly. The
projector can assign IP Address up to 11 devices.
* Infrastructure is one of the wireless LAN communication methods with having
an access point to communicate. If communicating with existing network, consult
with your network administrator.
Fig. 3.3.a Without an access point communication (Simple Access Point))
Fig. 3.3.b With an access point communication (Infrastructure)
・ Network settings can also be changed in Network Settings of Projector Web Control.
• Wireless LAN initial settings for the projector are as follows.
Mode: Simple Access Point
DHCP: Off
IP address: 192.168.10.1
Subnet Mask: 255.255.255.0
Default Gateway: 0.0.0.0
DNS Server: 0.0.0.0
SSID: SimpleAccessPoint*
SSID Broadcast: ON
Encryption: Off
CH: 11
*Change default setting before use not to overlap.
• The same network address cannot be used for both wireless LAN and wired LAN.
・Communication speed of the projector may be deteriorated in Simple Access
Point mode depending on the number of connected devices.
・Network communication cannot be available between the devices connected to
the projector in Simple Access Point mode.
NOTE

10
3.3.1 Connection in Simple Access Point Mode
Set the following when connecting the projector and the computer in Simple
Access Point mode.
Projector setting
[Restriction on plugging and unplugging the USB wireless adapter]
Before you insert or pull out the USB wireless adapter from the projector, turn off
the power of the projector and pull out the power cord’s plug from the outlet.
Do not touch the USB wireless adapter that is connected to the projector while the
projector is receiving AC power.
Do not use any extension cable or device when connecting the adapter to the projector.
1) Attach the USB wireless adapter to the WIRELESS port
of the projector.
2) Turn on the projector.
3) Press the MENU button on the remote control or the
control panel of the projector.
The MENU you last used appears.
Use the cursor button to select the following.
EASY MENU > ADVANCED MENU > NETWORK > WIRELESS SETUP
4) Set the following items in WIRELESS SETUP.
・MODE: SIMPLE ACCESS POINT
・IP ADDRESS
・SSID
・SSID BROADCAST
・ENCRYPTION
・CH
Select APPLY, then press the ENTER button to apply the settings.
About network setting
・The fourth octet of the projector's IP address is xed to 1.
・Subnet mask of the projector is xed to 255.255.255.0.
• As for the procedure of setting network and wireless connection for the computer,
refer to the manual of computer or wireless LAN device.
NOTE
Computer setting
1) The DHCP server function of the projector is always enabled. Enable the DHCP
setting of the computer.
2) Select SSID set for the projector by following the procedure of wireless
connection of the computer. Enter encryption key by following the computer’s
instruction if it is encrypted.