Hitachi CP-WU9100 User manual

1
Projector
CP-WU9100/CP-HD9950
User's Manual (detailed)
Operating Guide – Technical
Supported signals for COMPUTER IN
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720 x 400 TEXT 37.9 85 VESA
640 x 480 VGA (60Hz) 31.5 59.9 VESA
VGA (72Hz) 37.9 72.8 VESA
VGA (75Hz) 37.5 75 VESA
VGA (85Hz) 43.3 85 VESA
800 x 600 SVGA (56Hz) 35.2 56.3 VESA
SVGA (60Hz) 37.9 60.3 VESA
SVGA (72Hz) 48.1 72.2 VESA
SVGA (75Hz) 46.9 75 VESA
SVGA (85Hz) 53.7 85.1 VESA
832 x 624 Mac 16” mode 49.7 74.5 -
1024 x 768 XGA (60Hz) 48.4 60 VESA
XGA (70Hz) 56.5 70.1 VESA
XGA (75Hz) 60 75 VESA
XGA (85Hz) 68.7 85 VESA
1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA
1280 x 768 W-XGA (60Hz) 47.7 60 VESA
1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA
1280 x 1024 SXGA (60Hz) 64 60 VESA
SXGA (75Hz) 80 75 VESA
SXGA (85Hz) 91.1 85 VESA
*1 1366 x 768 WXGA (60Hz) 47.7 59.8 VESA
1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA
1600 x 900 WXGA++ (60Hz) 60 60 VESA
1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA
1600 x 1200 UXGA (60Hz) 75 60 VESA
1920 x 1080 Full HD (60Hz) 67.5 60 VESA
*2 1920 x 1200 W-UXGA (60Hz)
Reduced Blanking
74 60 VESA
*1) Only for CP-HD9950 *2) Only for CP-WU9100
(continued on next page)

2
Supported signals
Supported signals for HDMI / HDBaseT
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720 x 400 TEXT 37.9 85 VESA
640 x 480 VGA (60Hz) 31.5 59.9 VESA
VGA (72Hz) 37.9 72.8 VESA
VGA (75Hz) 37.5 75 VESA
VGA (85Hz) 43.3 85 VESA
800 x 600 SVGA (56Hz) 35.2 56.3 VESA
SVGA (60Hz) 37.9 60.3 VESA
SVGA (72Hz) 48.1 72.2 VESA
SVGA (75Hz) 46.9 75 VESA
SVGA (85Hz) 53.7 85.1 VESA
832 x 624 Mac 16” mode 49.7 74.5 -
1024 x 768 XGA (60Hz) 48.4 60 VESA
XGA (70Hz) 56.5 70.1 VESA
XGA (75Hz) 60 75 VESA
XGA (85Hz) 68.7 85 VESA
1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA
1280 x 768 W-XGA (60Hz) 47.7 60 VESA
1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA
1280 x 1024 SXGA (60Hz) 64 60 VESA
SXGA (75Hz) 80 75 VESA
SXGA (85Hz) 91.1 85 VESA
1366 x 768 WXGA (60Hz) 47.7 59.8 VESA
1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA
1600 x 900 WXGA++ (60Hz) 60 60 VESA
1400 x 1050 SXGA+ (60Hz) 65.2 60 VESA
1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA
1600 x 1200 UXGA (60Hz) 75 60 VESA
*1 1920 x 1200 W-UXGA (60Hz)
Reduced Blanking
74 60 VESA
*1) Only for CP-WU9100
(continued on next page)

3
Supported signals
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720(1440) x 480i 480i 15.7 60 CEA
720(1440) x 576i 576i 15.6 50 CEA
720 x 480p 480p 31.5 60 CEA
720 x 576p 576p 31.3 50 CEA
1280 x 720p 720p (50Hz) 37.5 50 CEA
720p (60Hz) 45 60 CEA
1920 x 1080i 1080i (50Hz) 28.1 50 CEA
1080i (60Hz) 33.8 60 CEA
1920 x 1080p 1080p (50Hz) 56.3 50 CEA
1080p (60Hz) 67.5 60 CEA
(continued on next page)

4
Supported signals
(continued on next page)
Supported signals for DVI-D
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720 x 400 TEXT 37.9 85 VESA
640 x 480 VGA (60Hz) 31.5 59.9 VESA
VGA (72Hz) 37.9 72.8 VESA
VGA (75Hz) 37.5 75 VESA
VGA (85Hz) 43.3 85 VESA
800 x 600 SVGA (56Hz) 35.2 56.3 VESA
SVGA (60Hz) 37.9 60.3 VESA
SVGA (72Hz) 48.1 72.2 VESA
SVGA (75Hz) 46.9 75 VESA
SVGA (85Hz) 53.7 85.1 VESA
832 x 624 Mac 16” mode 49.7 74.5 -
1024 x 768 XGA (60Hz) 48.4 60 VESA
XGA (70Hz) 56.5 70.1 VESA
XGA (75Hz) 60 75 VESA
XGA (85Hz) 68.7 85 VESA
1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA
1280 x 768 W-XGA (60Hz) 47.7 60 VESA
1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA
1280 x 1024 SXGA (60Hz) 64 60 VESA
SXGA (75Hz) 80 75 VESA
SXGA (85Hz) 91.1 85 VESA
1366 x 768 WXGA (60Hz) 47.7 59.8 VESA
1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA
1600 x 900 WXGA++ (60Hz) 60 60 VESA
1400 x 1050 SXGA+ (60Hz) 65.2 60 VESA
1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA
1600 x 1200 UXGA (60Hz) 75 60 VESA
*1 1920 x 1200 W-UXGA (60Hz)
Reduced Blanking
74 60 VESA
*1) Only for CP-WU9100

5
Supported signals
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720(1440) x 480i 480i 15.7 60 CEA
720(1440) x 576i 576i 15.6 50 CEA
720 x 480p 480p 31.5 60 CEA
720 x 576p 576p 31.3 50 CEA
1280 x 720p 720p (50Hz) 37.5 50 CEA
720p (60Hz) 45 60 CEA
1920 x 1080i 1080i (50Hz) 28.1 50 CEA
1080i (60Hz) 33.8 60 CEA
1920 x 1080p 1080p (50Hz) 56.3 50 CEA
1080p (60Hz) 67.5 60 CEA
(continued on next page)

6
Supported signals
Supported signals for SDI/DIGITAL1
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720 x 480i 480i 15.7 60 SMPTE
720 x 576i 576i 15.6 50 SMPTE
1280 x 720p 720p (50Hz) 37.5 50 SMPTE
720p (60Hz) 45 60 SMPTE
1920 x 1080i 1080i (50Hz) 28.1 50 SMPTE
1080i (60Hz) 33.8 60 SMPTE
1920 x 1080sf 1080i (25Hz) 28.1 50 SMPTE
1080i (30Hz) 33.8 60 SMPTE
1920 x 1080p 1080p (50Hz) 56.3 50 SMPTE
1080p (60Hz) 67.5 60 SMPTE
Only support 3G-SDI Level-A signal.
NOTE
• Be sure to check jack type, signal level, timing and resolution before connecting
this projector to a PC.
• Some PCs may have multiple display screen modes. Use of some of these modes is not
possible with this projector.
• Depending on the input signal, full-size display may not be possible in some cases. Refer to the
number of display pixels above.
• The signal is converted to the projector’s panel resolution before being displayed. The best
display performance is achieved if the resolutions of the input signal and projector panel are
identical.
• Automatic adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a composite sync or a
sync on G.
• The illustrations in this manual are for illustrative purposes. They may differ slightly from
your projector.

7
Connection to the ports
ACOMPUTER IN, BMONITOR OUT
D-sub 15pin mini shrink jack
<Computer signal>
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)
• H/V. sync. signal: TTL level (positive/negative)
• Composite sync. signal: TTL level
<Component video signal>
• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated
Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated
Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated
• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60
Pin Signal Pin Signal
1Video Red, Cr/Pr 9 (No connection)
2Video Green, Y 10 Ground
3Video Blue, Cb/Pb 11 (No connection)
4 (No connection) 12 A: SDA (DDC data) B: (No connection)
5 Ground 13 H. sync / Composite sync.
6Ground Red, Ground Cr/Pr 14 V. sync.
7Ground Green, Ground Y 15 A: SCL (DDC clock) B: (No connection)
8Ground Blue, Ground Cb/Pb
Connection to the ports
① ⑤④③②
⑥ ⑩⑨⑧⑦
⑪ ⑮⑭⑬⑫ ①⑤④③②
⑥⑩ ⑨ ⑧ ⑦
⑪⑮⑭⑬⑫
Connection to the ports
NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the
input ports of the projector are recessed.
►Only the signal that is input from the COMPUTER IN can be output from the
MONITOR OUT port.
A
B

8
Connection to the ports
Connection to the ports
DVI-D
DVI-D jack (digital to digital)
Pin Signal Pin Signal Pin Signal
1 T.M.D.S. Data2 - 9 T.M.D.S. Data1 - 17 T.M.D.S. Data0 -
2 T.M.D.S. Data2 + 10 T.M.D.S. Data1 + 18 T.M.D.S. Data0 +
3T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield
4 - 12 - 20 -
5 - 13 - 21 -
6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield
7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock +
8 - 16 Hot Plug Detect 24 T.M.D.S. Clock -
E
CHDMI 1, DHDMI 2
HDMITM connector
Pin Signal Pin Signal Pin Signal
1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL
2T.M.D.S. Data2 Shield 9 T.M.D.S. Data0 - 16 SDA
3 T.M.D.S. Data2 - 10 T.M.D.S. Clock + 17 DDC/CEC Ground
4 T.M.D.S. Data1 + 11 T.M.D.S. Clock Shield 18 +5V Power
5T.M.D.S. Data1 Shield 12 T.M.D.S. Clock - 19 Hot Plug Detect
6 T.M.D.S. Data1 - 13 CEC
7 T.M.D.S. Data0 + 14 Reserved (N.C. on device)
① ⑤
④
③
②⑥⑩
⑨
⑧
⑦⑪⑮
⑭
⑬
⑫
⑲
⑱
⑰
⑯
①⑤
④
③
②⑥⑩
⑨
⑧
⑦⑪⑮
⑭
⑬
⑫
⑲
⑱
⑰
⑯
CD E

9
Connection to the ports
Connection to the ports
G
CONTROL
D-sub 9pin plug
* About the details of RS-232C communication,
refer to the next section.
Pin Signal Pin Signal Pin Signal
1 (No connection) 4 (No connection) 7 RTS
2RD 5 Ground 8 CTS
3 TD 6 (No connection) 9 (No connection)
① ②
⑥⑦⑧⑨
⑤④③
①②
⑥⑦⑧⑨
⑤④③
VIDEO
BNC jack
• Composite video signal, Analog, 1.0±0.1Vp-p, 75Ω terminator
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz)
F
GF

10
Connection to the ports
H
Connection to the ports
H
HDBaseT
RJ-45 jack
Pin Signal Pin Signal Pin Signal
1 HDBaseT0+ 4 HDBaseT2+ 7 HDBaseT3+
2 HDBaseT0- 5 HDBaseT2- 8 HDBaseT3-
3 HDBaseT1+ 6 HDBaseT1-
① ⑤
④
③
② ⑥ ⑧
⑦
①⑤
④
③
②⑥⑧
⑦
I
LAN
RJ-45 jack
Pin Signal Pin Signal Pin Signal
1 TX+ 4 - 7 -
2 TX- 5 - 8 -
3RX+ 6 RX-
① ⑤
④
③
② ⑥ ⑧
⑦
①⑤
④
③
②⑥⑧
⑦
I

11
Connection to the ports
Connection to the ports
REMOTE CONTROL KIN, LOUT
Ø3.5 stereo mini jack
JWIRELESS
Only for USB wireless adapter.
Pin Signal
1 +5V
2 - Data
3+ Data
4Ground
① ④③②
①④ ③ ②
L
K
J
MSDI/DIGITAL1
BNC jack x1
• SD/HD/3G-SDI signal, Digital, 0.8V±10%, 75Ω terminated
• System:
SD-SDI signal: conforming to SMPTE ST 259-C standard
YCBCR 4:2:2 10-bit
480i, 576i
Single link HD-SDI signal: conforming to SMPTE ST 292 standard
YPBPR 4:2:2 10-bit
720p@50/60, 1080i@50/60, 1080sf@25/30
3G-SDI Level-A signal: conforming to SMPTE ST 424 standard
YPBPR 4:2:2 10-bit
1080p@50/60
M

12
① ②
⑥⑦⑧⑨
⑤④③
①②
⑥⑦⑧⑨
⑤④③
CD (1) (1) －
RD(2) (2) RD
TD (3) (3) TD
DTR (4) (4) －
GND (5) (5) GND
DSR (6) (6) －
RTS (7) (7) RTS
DTS (8) (8) CTS
RI (9) (9) －
RS-232C Communication
RS-232C Communication
When the projector connects to the computer by RS-232C communication, the
projector can be controlled with RS-232C commands from the computer.
For details of RS-232C commands, refer to RS-232C Communication / Network
command table (&21).
Connection
1. Turn off the projector and the computer.
2. Connect the projector's CONTROL port and the computer's RS-232C port
with a RS-232C cable (cross). Use the cable that fullls the specication
shown in gure.
3.
Turn the computer on, and turn the projector on after the computer has started up.
4. Set the COMMUNICATION TYPE to OFF in the COMMUNICATION menu of the
OPTION - SERVICE menu.
1
9876
5432
1
9876
5432
CONTROL port
of the projector
RS-232C port
of the computer
RS-232C cable
(cross)
RS-232C CONTROL

13
RS-232C Communication
Communication settings
1. Protocol
19200bps, 8N1
2. Command format (h shows hexadecimal)
Byte Number 0 1 2 3 4 5 6 7 8 9 10 11 12
Command
Action
Header Data
Header
code
Packet
Data
size
CRC
ag Action Type Setting code
L H L H L H L H L H L H
<SET> Change setting to
desired value [(cL)(cH)]
by [(bL)(bH)].
BEh EFh 03h 06h 00h
(aL) (aH) 01h 00h (bL) (bH) (cL) (cH)
<GET> Read projector
internal setup value [(bL)
(bH)] .
(aL) (aH) 02h 00h (bL) (bH) 00h 00h
<INCREMENT>
Increment setup value
[(bL)(bH)] by 1.
(aL) (aH) 04h 00h (bL) (bH) 00h 00h
<DECREMENT>
Decrement setup value
[(bL)(bH)] by 1.
(aL) (aH) 05h 00h (bL) (bH) 00h 00h
<EXECUTE> Run a
command [(bL)(bH)].
(aL) (aH) 06h 00h (bL) (bH) 00h 00h
[Header code] [Packet] [Data size]
Set [BEh, EFh, 03h, 06h, 00h] to byte number 0 to 4.
[CRC ag]
For byte number 5 and 6, refer to RS-232C Communication / Network
command table (&21).
[Action]
Set functional code to byte number 7 and 8.
<SET> = [01h, 00h], <GET> = [02h, 00h], <INCREMENT> = [04h, 00h]
<DECREMENT> = [05h, 00h], <EXECUTE> = [06h, 00h]
Refer to the Communication command table (&above).
[Type] [Setting code]
For byte number 9 to 12, refer to RS-232C Communication / Network
command table (&21).

14
RS-232C Communication
3. Response code / Error code (h shows hexadecimal)
(1) ACK reply: 06h
When the projector receives the Set, Increment, Decrement or Execute
command correctly, the projector changes the setting data for the specied
item by [Type], and it returns the code.
(2) NAK reply: 15h
When the projector cannot understand the received command, the projector
returns the error code.
In such a case, check the sending code and send the same command again.
(3) Error reply: 1Ch + 0000h
When the projector cannot execute the received command for any reasons,
the projector returns the error code.
In such a case, check the sending code and the setting status of the projector.
(4) Data reply: 1Dh + xxxxh
When the projector receives the GET command correctly, the projector returns
the response code and 2 bytes of data.
NOTE • For connecting the projector to your devices, read the manual for
each devices, and connect them correctly with suitable cables.
• Operation cannot be guaranteed when the projector receives an undened
command or data.
• Provide an interval of at least 40ms between the response code and any
other code.
• The projector outputs test data when the power supply is switched ON, and
when the lamp is lit. Ignore this data.
• Commands are not accepted during warm-up.
• When the data length is greater than indicated by the data length code, the
projector ignores the excess data code. Conversely when the data length is
shorter than indicated by the data length code, the projector returns the error
code to the computer.

15
When the projector connects to the network, the projector can be controlled with
RS-232C commands from the computer with web browser.
For details of RS-232C commands, refer to RS-232C Communication / Network
command table (&21).
Command Control using the Network
Connection
1. Turn off the projector and the computer.
2. If you use wired LAN, connect the projector's LAN or HDBaseTTM port to the
computer's LAN or HDBaseT port with a LAN cable. Use the cable that fullls
the specication shown in gure. If you use wireless LAN, insert the USB
wireless adapter into the WIRELESS port of the projector.
3. Turn the computer on, and turn the projector on after the computer has
started up.
NOTE • If data is transferred using wireless and wired LAN at the same time,
the projector may not be able to process the data correctly.
Command Control using the Network
USB wireless adapter
LAN or
HDBaseT port
LAN or HDBaseT port
・LAN cable (CAT-5e or greater)
or
・For HDBaseT connection
- CAT-5e or greater
- shielded type (connectors included)
- straight cable
- single cable
WIRELESS port

16
Communication Port
The following two ports are assigned for the command control.
TCP #23
TCP #9715
Congure the following items from a web browser when command control is used.
Port Settings
Network Control
Port1 (Port: 23)
Port open
Click the [Enable] checkbox to open [Network
Control Port1 (Port: 23)] to use TCP #23.
Default setting is Enable
Authentication
Click the [Enable] check box for the
[Authentication] setting when authentication
is required.
Default setting is Disable.
Network Control
Port2 (Port: 9715)
Port open
Click the [Enable] check box to open [Network
Control Port2 (Port: 9715)] to use TCP
#9715.
Default setting is Enable.
Authentication
Click the [Enable] check box for the
[Authentication] setting when authentication
is required.
Default setting is Enable.
Command Control using the Network
When the authentication setting is enabled, the following settings are required.
Security Settings
Network Control
Authentication
Password Enter the required authentication password.
Conrm this setting is the same for [Network
Control Port1 (Port: 23)] and [Network
Control Port2 (Port: 9715)].
Default setting is blank.
Re-enter
Authentication
Password

17
Command Control using the Network
Command control settings
[TCP #23]
1. Command format
Same as RS-232C communication, refer to RS-232C Communication command format.
2. Response code / Error code (h shows hexadecimal)
Four of the response / error code used for TCP#23 are the same as RS-232C
Communication (1)~(4). One authentication error reply (5) is added.
(1) ACK reply : 06h
Refer to RS-232C communication (&14).
(2) NAK reply : 15h
Refer to RS-232C communication (&14).
(3) Error reply : 1Ch + 0000h
Refer to RS-232C communication (&14).
(4)
Data reply : 1Dh + xxxxh
Refer to RS-232C communication (&14).
(5) Authentication error reply : 1Fh + 0400h
When authentication error occurs, the projector returns the error code.
[TCP #9715]
1. Command format
The commands that some datum are added to the head and the end of the ones
of TCP#9715 are used.
Header Data length RS-232C command Check sum Connection ID
0×02 0×0D 13 bytes 1 byte 1 byte
[Header]
02, Fixed
[Data Length]
RS-232C commands byte length (0×0D, Fixed)
[RS-232C commands]
Refer to RS-232C Communication command format (&13).
[Check Sum]
This is the value to make zero on the addition of the lower 8 bits from the header
to the checksum.
[Connection ID]
Random value from 0 to 255 (This value is attached to the reply data).
NOTE • Operation cannot be guaranteed when the projector receives an
undened command or data.
• Provide an interval of at least 40ms between the response code and any other
code.
• Commands are not accepted during warm-up.

18
NOTE • For the transmission of the second or subsequent commands, the
authentication data can be omitted for the same connection.
Command Control using the Network
2. Response code / Error code (h shows hexadecimal)
The connection ID is attached for the TCP#23's response / error codes are
used. The connection ID is the same as the sending command format.
(1) ACK reply: 06h + ××h (××h : connection ID)
(2) NAK reply: 15h + ××h
(3) Error reply: 1Ch + 0000h + ××h
(4) Data reply: 1Dh + xxxxh + ××h
(5) Authentication error reply: 1Fh + 0400h + ××h
(6) Projector busy reply: 1Fh + ××××h + ××h
When the projector is too busy to receive the command, the projector returns
the error code.
In such a case, check the sending code and send the same command again.
Automatic Connection Break
The TCP connection will be automatically disconnected after there is no
communication for 30 seconds after being established.
Authentication
The projector does not accept commands without authentication success
when authentication is enabled. The projector uses a challenge response type
authentication with an MD5 (Message Digest 5) algorithm.
When the projector is connected to a LAN, a random 8 bytes will be returned
if authentication is enabled. Bind this received 8 bytes and the authentication
password, and digest the data with the MD5 algorithm, and add it in front of the
commands to send.
Following is a sample of authentication process.
Authentication password: password (example)
Random 8 bytes: a572f60c (example)
1) Select a projector and receive the random 8 bytes from the projector.
a572f60c
2) Bind the random 8 bytes and the authentication password.
 a572f60cpassword
3) Digest this bound with MD5 algorithm.
e3d97429adffa11bce1f7275813d4bde
4) Add this code in front of the commands and send the data.
e3d97429adffa11bce1f7275813d4bde + [command].
5) When the sent data is correct, the command will be performed and the reply
data will be returned. Otherwise, an authentication error will be returned.

19
This projector is equipped with NETWORK BRIDGE function.
When the projector connects to the computer by wired or wireless LAN
communication, an external device that is connected with this projector by RS-
232C communication can be controlled from the computer as a network terminal.
For details, see the 7. Network Bridge function in the Network Guide.
Network Bridge Communication
NOTE • If data is transferred using wireless and wired LAN at the same time,
the projector may not be able to process the data correctly.
Connection
1. If you use wired LAN, connect the computer's LAN port and the projector's
LAN port with a LAN cable. Use the cable that fullls the specication shown
in gure. If you use wireless LAN, insert the USB wireless adapter into the
projector's WIRELESS port.
2. Connect the projector's CONTROL port and the RS-232C port of the devices
that you want to control with a RS-232C cable.
3. Turn the computer on, and turn the projector on after the computer has
started up.
4. Set the COMMUNICATION TYPE to NETWORK BRIDGE in the
COMMUNICATION menu of the OPTION - SERVICE menu.
Network Bridge Communication
USB wireless adapter
LAN port
・LAN cable (CAT-5e or greater)
- CAT-5e or greater
- shielded type (connectors included)
- straight cable
- single cable
WIRELESS port
LAN port
RS-232C
RS-232C cable
(cross)

20
Communication settings
For communication setting, use the COMMUNICATION menu in the OPTION -
SERVICE menu.
Item Condition
BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps
Data length 8 bit (xed)
PARITY NONE/ODD/EVEN
Start bit 1 bit (xed)
Stop bit 1 bit (xed)
Transmission method HALF-DUPLEX/FULL-DUPLEX
NOTE • For connecting the projector to your devices, read the manual for
each devices, and connect them correctly with suitable cables.
• Turn off the power and unplug both the projector and other devices before
connecting them.
• For details of Transmission method, refer to 7.4 Transmission method in the
Network Guide.
Network Bridge Communication