Hitachi CP-X8 User manual

1
Projector
CPX7/CPX8/CPX9
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read “Safety Guide” rst. After reading them, store them in a
safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.

• Mac® is a registered trademark of Apple Inc.
• Microsoft®, Internet Explorer®, Windows® and Windows Vista® are registered
trademarks of Microsoft Corporation in the U.S. and/or other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
• HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
All other trademarks are the properties of their respective owners.
NOTICE This entry notices of fear of causing trouble.

2
Contents
Contents
Introduction . . . . . . . . . . . . . . . 3
Features ......................3
Checking the contents of package ...3
Part names . . . . . . . . . . . . . . . . 4
Projector ......................4
Control panel ...................5
Rear panel ....................5
Remote control . . . . . . . . . . . . . . . . . 6
Setting up . . . . . . . . . . . . . . . . . 7
Arrangement ...................7
Connecting your devices .........10
Connecting power supply . . . . . . . . 12
Using the security bar and slot . . . . 12
Remote control ............13
Installing the batteries ...........13
About the remote control signal . . . 13
Power on/off . . . . . . . . . . . . . . 14
Turning on the power . . . . . . . . . . . 14
Turning off the power . . . . . . . . . . . 14
Operating . . . . . . . . . . . . . . . . 16
Adjusting the volume ............16
Temporarily muting the sound .....16
Selecting an input signal .........16
Searching an input signal . . . . . . . . 18
Selecting an aspect ratio .........18
Adjusting the projector's elevator . . 19
Adjusting the zoom and focus .....19
Using the automatic adjustment feature ...20
Adjusting the position . . . . . . . . . . . 20
Correcting the keystone distortions . . 21
Using the magnify feature ........22
Temporarily freezing the screen . . . 23
Temporarily blanking the screen . . 23
Using the menu function . . . . . . . . 24
EASY MENU. . . . . . . . . . . . . . . 26
As p e c t , Au t o k e y s t o n e , ke y s t o n e ,
pi c t u r e m o d e , ec o m o d e , mi r r o r , re s e t ,
Fi l t e r t i m e , lA n g u A g e , Ad v A n c e d m e n u ,
ex i t

PICTURE menu . . . . . . . . . . . . 28
Br i g h t n e s s , co n t r A s t , gA m m A ,
co l o r t e m p , co l o r , ti n t , sh A r p n e s s ,
mym e m o r y
IMAGE menu . . . . . . . . . . . . . . 31
As p e c t , ov e r s c A n , v p o s i t i o n , h p o s i t i o n ,
h p h A s e , h s i z e , Au t o A d j u s t e x e c u t e
INPUT menu . . . . . . . . . . . . . . 34
pr o g r e s s i v e , vi d e o n r , co l o r s p A c e ,
vi d e o F o r m A t , hd m i F o r m A t , hd m i r A n g e ,
co m p u t e r i n , Fr A m e l o c k , re s o l u t i o n
SETUP menu ..............38
Au t o k e y s t o n e , ke y s t o n e , Au t o e c o m o d e
ec o m o d e , mi r r o r , st A n d B y m o d e ,
mo n i t o r o u t
AUDIO menu . . . . . . . . . . . . . . 40
vo l u m e , sp e A k e r , Au d i o s o u r c e ,
hd m i A u d i o
SCREEN menu.............41
lA n g u A g e , me n u p o s i t i o n , Bl A n k ,
st A r t u p ,
MyScreen, MyScreen Lock
,
me s s A g e , so u r c e n A m e , te m p l A t e , c.c.
OPTION menu . . . . . . . . . . . . . 47
Au t o s e A r c h , Au t o k e y s t o n e ,
di r e c t p o w e r o n , Au t o p o w e r o F F ,
lA m p t i m e , Fi l t e r t i m e , myB u t t o n ,
mys o u r c e , se r v i c e
SECURITY menu ...........52
se c u r i t y p A s s w o r d c h A n g e ,
MyScreen
p A s s w o r d , pi n l o c k ,
tr A n s i t i o n d e t e c t o r , myt e x t p A s s w o r d ,
myt e x t d i s p l A y , myt e x t w r i t i n g
Maintenance ..............58
Replacing the lamp .............58
Cleaning and replacing the air lter . . 60
Other care ....................62
Troubleshooting . . . . . . . . . . . 63
Related messages . . . . . . . . . . . . . 63
Regarding the indicator lamps . . . . 64
Resetting all settings ............65
Phenomena that may be easy
to be mistaken for machine defects . . 66
Specications .............70


3
Introduction
• Keep the original packing materials, for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
NOTE
Introduction
The projector provides you with the broad use by the following features.
Checking the contents of package
ü This projector has a variety of I/O ports that supposedly cover for any
business scene. The HDMI port can support various image equipment
which have digital interface to get clearer pictures on a screen.
ü This projector realizes the large projection image, even if in a small space.
ü The new double layer lter system is expected to function longer and offers
you less maintenance frequency.
ü This compact, lightweight projector uses a front exhaust system that keeps
the user comfortable by directing hot air away from the user.
Please see the Contents of package section in the User’s Manual (concise)
which is a book. Require of your dealer immediately if any items are missing.
Features

4
Part names
Part names
Projector
(1) Lamp cover (58)
The lamp unit is inside.
(2) Focus ring (19)
(3) Zoom ring (19)
(4) Control panel (5)
(5) Elevator buttons (x 2) (19)
(6) Elevator feet (x 2) (19)
(7) Remote sensor (13)
(8) Lens (62)
(9) Intake vents
(10) Filter cover (60)
The air lter and intake vent are
inside.
(11) Speaker (40)
(12) Exhaust vent
(13) AC IN (AC inlet) (12)
(14) Rear panel (5)
(15) Security bar (12)
(16) Security slot (12)
►HOT! : Do not touch around the lamp cover and the exhaust
vents during use or just after use, since it is too hot.
►Do not look into the lens or vents while the lamp is on, since the strong light is
not good for your eyes.
►Do not handle the elevator buttons without holding the projector, since the
projector may drop down.
►Do not use the security bar and slot to prevent the projector from falling down,
since it is not designed for it.
WARNING
►Maintain normal ventilation to prevent the projector from
heating up. Do not cover, block or plug up the vents. Do not place anything that
can stick or be sucked to the vents, around the intake vents. Clean the air lter
periodically.
CAUTION
HOT!
HOT! (12)
(1) (2) (3) (4)
(7)
(9)
(8)
(10)
(6)
(5)
(11)
(6)
(15)
(13) (16)
(14)
(5)
(9)

5
Part names
Control panel
(1) STANDBY/ON button (14)
(2) INPUT button (16, 24)
(3) MENU button (24)
It consists of four cursor buttons.
(4) BLANK button (23)
(5) POWER indicator (12, 14, 64)
(6) TEMP indicator (64)
(7) LAMP indicator (64)
Rear panel (10)
(1) VIDEO port
(2) S-VIDEO port
(3) AUDIO IN1 port
(4) AUDIO IN2 port
(5) AUDIO OUT port
(6) COMPUTER IN port
(7) HDMI port
(8) CONTROL port
(9) MONITOR OUT port
%/$1.
0<%87721
(1) (3)(2)
(4)
(7)(6) (5)
(2) (3) (6) (7)
(8)(9) (4)(5)(1)

6
Part names
Remote control
(1) VIDEO button (17)
(2) COMPUTER button (17)
(3) SEARCH button (18)
(4) STANDBY/ON button (14)
(5) ASPECT button (18)
(6) AUTO button (20)
(7) BLANK button (23)
(8) MAGNIFY - ON button (22)
(9) MAGNIFY - OFF button (22)
(10) MY SOURCE/DOC.CAMERA button (17, 49)
(11) VOLUME - button (16)
(12) PAGE UP button *
(13) PAGE DOWN button *
(14) VOLUME + button (16)
(15) MUTE button (16)
(16) FREEZE button (23)
(17) MY BUTTON - 1 button (49)
(18) MY BUTTON - 2 button (49)
(19) KEYSTONE button (21)
(20) POSITION button (20, 25)
(21) MENU button (24)
(22) ▲/▼/◄/► cursor buttons (24)
(23) ENTER button (24)
(24) ESC button (24)
(25) RESET button (24)
(26) Battery cover (13)
Back of
the remote control
(26)
(2)
(1)
(6)
(5)
(16)
(8)
(9)
(19)
(17)
(20)
(22)
(24)
(10)
(4)
(3)
(7)
(12)
(14)
(11)
(13)
(15)
(18)
(21)
(23)
(25)
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
• Any button marked with “*” is not supported on this projector (63).
NOTE

7
Setting up
Install the projector according to the environment and manner the projector will be
used in.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection
distance.
The values shown in the table are calculated for a full size screen: 1024 x 768
a Screen size (diagonal) b
Projection distance (±10%, from the projector's end)
c1 , c2 Screen height (±10%)
On a horizontal surface
<CPX7>
Suspended from the ceiling
• Keep a space of 30 cm or more between the
sides of the projector and other objects such
as walls.
• For the case of installation in a special
state such as ceiling mount, the specied
mounting accessories (70) and service may
be required. Before installing the projector,
consult your dealer about your installation.
Setting up
Screen size
(diagonal)
4 : 3 screen 16 : 9 screen
Projection distance Screen
height
Screen
height
Projection distance Screen
height
Screen
height
min. max. min. max.
type
(inch) m m inch m inch cm inch cm inch m inch m inch cm inch cm inch
30 0.8 0.9 34 1.1 42 39 15 7 3 0.9 34 1.1 42 36 14 1 0
40 1.0 1.2 46 1.4 57 52 21 9 3 1.2 46 1.4 57 49 19 1 0
50 1.3 1.5 59 1.8 71 65 26 11 41.5 59 1.8 71 61 24 1 1
60 1.5 1.8 71 2.2 86 78 31 13 5 1.8 71 2.2 86 73 29 2 1
70 1.8 2.1 83 2.6 101 91 36 15 6 2.1 83 2.6 101 85 34 2 1
80 2.0 2.4 95 2.9 115 105 41 17 7 2.4 95 2.9 115 97 38 2 1
90 2.3 2.7 107 3.3 130 118 46 20 8 2.7 107 3.3 130 109 43 3 1
100 2.5 3.0 119 3.7 145 131 51 22 9 3.0 119 3.7 145 122 48 3 1
120 3.0 3.7 144 4.4 174 157 62 26 10 3.7 144 4.4 174 146 57 4 1
150 3.8 4.6 180 5.5 218 196 77 33 13 4.6 180 5.5 218 182 72 4 2
200 5.1 6.1 241 7.4 292 261 103 44 17 6.1 241 7.4 292 243 96 6 2
250 6.4 7.7 302 9.3 365 327 129 54 21 7.7 302 9.3 365 304 120 7 3
300 7.6 9.2 363 11.1 438 392 154 65 26 9.2 363 11.1 438 365 144 9 4
b
abc1
c1 c2 c2

8
Arrangement (continued)
Setting up
Screen size
(diagonal)
4 : 3 screen 16 : 9 screen
Projection distance Screen
height
Screen
height
Projection distance Screen
height
Screen
height
min. max. min. max.
type
(inch) m m inch m inch cm inch cm inch m inch m inch cm inch cm inch
30 0.8 0.7 29 0.9 35 39 15 7 3 0.8 33 1.0 39 36 14 1 0
40 1.0 1.0 39 1.2 47 52 21 9 3 1.1 44 1.3 53 49 19 1 0
50 1.3 1.3 49 1.5 60 65 26 11 41.4 55 1.7 66 61 24 1 1
60 1.5 1.5 60 1.8 72 78 31 13 5 1.7 66 2.0 80 73 29 2 1
70 1.8 1.8 70 2.1 84 91 36 15 6 2.0 77 2.4 93 85 34 2 1
80 2.0 2.0 80 2.5 97 105 41 17 7 2.2 88 2.7 106 97 38 2 1
90 2.3 2.3 90 2.8 109 118 46 20 8 2.5 100 3.0 120 109 43 3 1
100 2.5 2.6 101 3.1 121 131 51 22 9 2.8 111 3.4 133 122 48 3 1
120 3.0 3.1 121 3.7 146 157 62 26 10 3.4 133 4.1 160 146 57 4 1
150 3.8 3.9 152 4.6 183 196 77 33 13 4.2 167 5.1 200 182 72 4 2
200 5.1 5.2 203 6.2 244 261 103 44 17 5.6 222 6.8 267 243 96 6 2
250 6.4 6.5 254 7.8 305 327 129 54 21 7.1 278 8.5 334 304 120 7 3
300 7.6 7.8 305 9.3 367 392 154 65 26 8.5 334 10.2 401 365 144 9 4
b
abc1
c1 c2 c2
<CPX8/CPX9>

9
Setting up
►Place the projector in a stable horizontal position. If the
projector falls or is knocked over, it could cause injury and/or damage to the
projector. Using a damaged projector could then result in re and/or electric
shock.
• Do not place the projector on an unstable, slanted or vibrational surface such
as a wobbly or inclined stand.
• Do not place the projector on its side, front or rear position.
• Consult with your dealer before a special installation such as suspending from
a ceiling or somewhere else.
►Place the projector in a cool place, and ensure that there is sufcient
ventilation. The high temperature of the projector could cause re, burns and/or
malfunction of the projector.
• Do not place or attach anything that would block the lens or vent holes.
• Keep a space of 30 cm or more between the sides of the projector and other
objects such as walls.
• Do not place the projector on metallic thing or anything weak in heat.
• Do not place the projector on carpet, cushions or bedding.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
• Do not place anything near the projector lens or vents, or on top of the
projector.
• Do not place anything that may be sucked into or stick to the vents on the
bottom of the projector. This projector has some intake vents also on the bottom.
►Do not place the projector anyplace where it may get wet. Getting the projector
wet or inserting liquid into the projector could cause re, electric shock and/or
malfunction of the projector.
• Do not place the projector in a bathroom or the outdoors.
• Do not place anything containing liquid near the projector.
►Do not place the projector where any oils, such as cooking or machine oil, are
used.
►Use only the mounting accessories the manufacturer specied, and leave
installing and removing the projector with the mounting accessories to the
service personnel.
• Read and keep the user’s manual of the mounting accessories used.
WARNING
►Avoid placing the projector in smoky, humid or dusty place.
Placing the projector in such places could cause re, electric shock and/or
malfunction of the projector.
• Do not place the projector near humidiers, smoking spaces or a kitchen. Also
do not use an ultrasonic humidier near the projector. Otherwise chlorine and
minerals contained in tap water are atomized and could be deposited in the
projector causing image degradation or other problems.
►Position the projector to prevent light from directly hitting the projector's remote
sensor.
CAUTION
Arrangement (continued)

10
AUDIO OUT AUDIO OUT
RGB OUT
Y CB/PBCR/PR
COMPONENT VIDEO OUT
L R
AUDIO OUT
VIDEO OUT L R
AUDIO OUT
L R
AUDIO OUT
S-VIDEO OUT
RS-232C
RGB IN
L R
AUDIO IN
HDMI
Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Please refer to the following illustrations
to connect them. To input component video signal to COMPUTER IN port, please
see the description of the COMPUTER IN item of the INPUT menu (36).
►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
WARNING
►Turn off all devices and unplug their power cords prior to
connecting them to projector. Connecting a live device to the projector may
generate extremely loud noises or other abnormalities that may result in
malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about non-
accessory cables which may be required a specic length or a ferrite core by
the regulations. For cables with a core only at one end, connect the end with
the core to the projector.
►Make sure that devices are connected to the correct ports. An incorrect
connection may result in malfunction or damage to the device and the projector.
NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the
input ports of the projector are recessed.
CAUTION
VCR/DVD/Blu-ray Disc player
Speakers
(with an
amplier)
PCMonitor

11
Setting up
• Be sure to read the manuals for devices before connecting them to
the projector, and make sure that all the devices are suitable to be connected
with this product. Before connecting to a PC, check the signal level, the signal
timing, and the resolution.
- Some signal may need an adapter to input this projector.
- Some PCs have multiple screen display modes that may include some signals
which are not supported by this projector.
- Although the projector can display signals with resolution up to UXGA
(1600X1200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and the projector panel are identical.
• While connecting, make sure that the shape of the cable's connector ts the
port to connect with. And be sure to tighten the screws on connectors with
screws.
• When connecting a laptop PC to the projector, be sure to activate the PC’s
external RGB output. (Set the laptop PC to CRT display or to simultaneous
LCD and CRT display.) For details on how this is done, please refer to the
instruction manual of the corresponding laptop PC.
• When the picture resolution is changed on a PC depending on an input,
automatic adjustment function may take some time and may not be completed.
In this case, you may not be able to see a check box to select “Yes/No” for the
new resolution on Windows. Then the resolution will go back to the original.
It might be recommended to use other CRT or LCD monitors to change the
resolution.
• In some cases, this projector may not display a proper picture or display
any picture on screen. For example, automatic adjustment may not function
correctly with some input signals. An input signal of composite sync or sync on
G may confuse this projector, so the projector may not display a proper picture.
NOTE
About Plug-and-Play capability
Plug-and-Play is a system composed of a PC, its operating system and
peripheral equipment (i.e. display devices). This projector is VESA DDC 2B
compatible. Plug-and-Play can be used by connecting this projector to a PC
that is VESA DDC (display data channel) compatible.
• Take advantage of this feature by connecting a computer cable to the
COMPUTER IN port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
• Please use the standard drivers in your PC as this projector is a Plug-and-
Play monitor.
Connecting your devices (continued)

12
Setting up
Connecting power supply
1. Put the connector of the power cord into the
AC IN (AC inlet) of the projector.
2. Firmly plug the power cord’s plug into the
outlet. In a couple of seconds after the
power supply connection, the POWER
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in re and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Never modify the power cord.
WARNING
Using the security bar and slot
AC IN Power cord
A commercially available anti-theft chain or wire can
be attached to the security bar on the projector.
Refer to the gure to choose an anti-theft chain or wire.
Also this product has the security slot for the
Kensington lock.
For details, see the manual of the security tool.
►Do not use the security bar and slot to prevent the projector
from falling down, since it is not designed for it.
WARNING
►Do not place anti-theft chain or wire near the exhaust vents. It
may become too hot.
CAUTION
• The security bar and slot is not comprehensive theft prevention
measures. It is intended to be used as supplemental theft prevention measure.
NOTE
Security bar
Security slot
Anti-theft chain or wire
Please remember that when the DIRECT POWER
ON function activated (47), the connection of
the power supply make the projector turn on.
Installation surface
18 mm
18 mm
10 mm
12 mm

13
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor)
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control
starts to malfunction, try to replace the batteries. If you will not use the remote control for
long period, remove the batteries from the remote control and store them in a safe place.
1. Holding the hook part of the battery
cover, remove it.
2. Align and insert the two AA batteries
(HITACHI MAXELL, Part No.LR6 or R6P)
according to their plus and minus terminals
as indicated in the remote control.
3.
Replace the battery cover in the direction of the arrow and snap it back into place.
►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in re, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specied. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
WARNING
• The remote control signal reected in the screen or the like may be available.
If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.
• The remote control uses infrared light to send signals to the projector (Class 1
LED), so be sure to use the remote control in an area free from obstacles that
could block the remote control’s signal to the projector.
• The remote control may not work correctly if strong light (such as direct sun
light) or light from an extremely close range (such as from an inverter uorescent
lamp) shines on the remote sensor of the projector. Adjust the position of
projector avoiding those lights.
NOTE
21 3
30º
3 m
30º
Approx.

14
Power on/off
1. Make sure that the power cord is rmly and
correctly connected to the projector and the
outlet.
Turning on the power
2. Make sure that the POWER indicator is
steady orange (64). Then remove the lens
cover.
3. Press STANDBY/ON button on the
projector or the remote control.
The projection lamp will light up and POWER
indicator will begin blinking in green. When the power
is completely on, the indicator will stop blinking and light in steady green
(64).
Power on/off
To display the picture, select an input signal according to the section “Selecting an
input signal” (16).
►A strong light is emitted when the projector’s power is on. Do
not look into the lens of the projector or look inside of the projector through any
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
WARNING
1. Press the STANDBY/ON button on the projector or the remote control. The
message “Power off?” will appear on the screen for about 5 seconds.
Turning off the power
2. Press the STANDBY/ON button again while the message appears.
The projector lamp will go off, and the POWER indicator will begin blinking in
orange. Then POWER indicator will stop blinking and light in steady orange
when the lamp cooling is complete (64).
3. Attach the lens cover, after the POWER indicator turns in steady orange.
STANDBY/ON button
POWER indicator
• Turn the power on/off in right order. Please power on the projector
prior to the connected devices.
• This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON
(47) and AUTO POWER OFF (48)
items of the OPTION menu.
NOTE
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTER MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
ー
ON
OFF
＋
FREEZE
Do not turn the projector on for about 10 minutes or more after turning it off. Also,
do not turn the projector off shortly after turning it on. Such operations might cause
the lamp to malfunction or shorten the lifetime of some parts including the lamp.

15
Power on/off
Precaution for lens cover attachment and removal
When you attach or remove the lens cover, move it vertically up and down while keeping
the knob to the right as illustrated in the gure.

16
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the
volume. If you do not do anything, the dialog will automatically
disappear after a few seconds.
● When is selected for current picture input port, the volume
adjustment is disabled. Please see AUDIO SOURCE item of
AUDIO menu (40).
● Even if the projector is in the standby state, the volume can be adjusted when
both of following conditions are satised.
- NORMAL is selected for the STANDBY MODE in the SETUP menu (39).
- An item other than is selected for the AUDIO OUT STANDBY of the
AUDIO SOURCE in the AUDIO menu (40).
1. Press MUTE button on the remote control.
A dialog will appear on the screen indicating that you have
muted the sound.
To restore the sound, press the MUTE, VOLUME + or
VOLUME - button. Even if you do not do anything, the dialog
will automatically disappear after a few seconds.
Temporarily muting the sound
● When is selected for current picture input port, the sound
is always muted. Please see AUDIO SOURCE item of
AUDIO menu (40).
● C.C. (Closed Caption) is automatically activated when sound is muted and an
input signal containing C.C. is received. This function is available only when
the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER
IN, and when AUTO is selected for DISPLAY in the C.C. menu under the
SCREEN menu (46).
1. Press INPUT button on the projector.
Each time you press the button, the projector switches its
input port from the current port as below.
Selecting an input signal
COMPUTER IN  HDMI
VIDEO

S-VIDEO
(continued on next page)
VOLUME +/- button
MUTE button
● While ON is selected for AUTO SEARCH item in OPTION
menu (47), the projector will keep checking the ports in
above order repeatedly till an input signal is detected.
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
INPUT button

17
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
Operating
1. Press VIDEO button on the remote control.
Each time you press the button, the projector switches its
input port from the current port as below.
Selecting an input signal (continued)
● While ON is selected for AUTO SEARCH item in OPTION
menu, the projector will keep checking every port sequentially
till an input signal is detected (47). If VIDEO button is
pressed when COMPUTER IN port is selected, the projector
will check HDMI port rst.
VIDEO button
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
MY SOURCE /
DOC. CAMERA button
1. Press COMPUTER button on the remote control to
select the COMPUTER IN port.
HDMI
 S-VIDEO  VIDEO
COMPUTER button
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
1. Press the MY SOURCE / DOC. CAMERA button on
the remote control. The input signal will be changed
into the signal you set as MY SOURCE (49).
● This function also can use for document camera. Select the
input port that connected the document camera.

18
1. Press ASPECT button on the remote control.
Each time you press the button, the projector switches the
mode for aspect ratio in turn.
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
1. Press SEARCH button on the remote control.
The projector will start to check its input ports as below in
order to nd any input signals.
When an input is found, the projector will stop searching
and display the image. If no signal is found, the projector will
return to the state selected before the operation.
Searching an input signal
● While ON is selected for AUTO SEARCH item in OPTION menu (47), the
projector will keep checking the ports in above order repeatedly till an input
signal is detected.
For a computer signal
NORMAL  4:3  16:9  16:10
For an HDMI signal
NORMAL  4:3  16:9  16:10  14:9
 For a video signal, s-video signal or component video
signal
4:3  16:9  14:9
 For no signal
4:3 (xed)
SEARCH button
ASPECT button
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
Operating
COMPUTER IN  HDMI
VIDEO

S-VIDEO

19
Operating
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the
elevator feet to place the projector horizontally.
Using the feet can also tilt the projector in order to project at
a suitable angle to the screen, elevating the front side of the
projector within 12 degrees.
This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is
adjustable while pulling up the elevator knob on the same side as it.
1. Holding the projector, pull the elevator knobs up to loose the elevator feet.
2. Position the front side of the projector to the desired height.
3. Release the elevator knobs in order to lock the elevator feet.
To loose an elevator foot,
pull up the elevator knob
on the same side as it.
To nely adjust, twist the foot.
4. After making sure that the elevator feet are locked, put the projector down
gently.
5. If necessary, the elevator feet can be manually twisted to make more precise
adjustments. Hold the projector when twisting the feet.
►Do not handle the elevator buttons without holding the
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 12 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
CAUTION
1. Use the zoom ring to adjust the screen size.
2. Use the focus ring to focus the picture.
Adjusting the zoom and focus Focus ring Zoom ring
12°
51

20
Operating
1. Press POSITION button on the remote control when no menu is
indicated.
The “POSITION” indication will appear on the screen.
Adjusting the position
2. Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press RESET button on
the remote control during the operation.
To complete this operation, press POSITION button again. Even if
you do not do anything, the dialog will automatically disappear
after a few seconds.
●
When this function is performed on a video signal or s-video signal or component
video signal, some image such as an extra-line may appear at outside of the picture.
● When this function is performed on a video signal or an s-video signal, the range
of this adjustment depends on OVER SCAN in IMAGE menu (31) setting. It is
not possible to adjust when OVER SCAN is set to 10.
● If POSITION button is pressed when a menu is indicated on screen, the displayed
picture does not move its position but the menu does.
● This function is unavailable for a signal from the HDMI port.
1. Press AUTO button on the remote control.
Pressing this button performs the following.
Using the automatic adjustment feature
 For a computer signal
The vertical position, the horizontal position and the horizontal
phase will be automatically adjusted.
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
 For a video signal and s-video signal
The video format best suited for the respective input signal will be selected
automatically. This function is available only when the AUTO is selected for
the VIDEO FORMAT item in the INPUT menu (35). The vertical position and
horizontal position will be automatically set to the default.
● The automatic adjustment operation requires approx. 10 seconds. Also please
note that it may not function correctly with some input.
● When this function is performed for a video signal, a certain extra such as a line
may appear outside a picture.
● When this function is performed for a computer signal, a black frame may be
displayed on the edge of the screen, depending on the PC model.
●
The items adjusted by this function may vary when the FINE or DISABLE is selected
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (50).
POSITION button
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
AUTO button
 For a component video signal
The vertical position and horizontal position will be automatically set to the
default. The horizontal phase will be automatically adjusted.
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
12
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE