Hitachi MP-WU8101W User manual

1QM00971-1
LCD Projector
MP-WU8101W/MP-WU8101B
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this projector, read all the manuals for this
projector. Read Safety Guide rst. After reading the manuals, store them in a
safe place for future reference.
WARNING
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This entry warns of a risk of serious personal injury or even
death.
This entry warns of a risk of personal injury or physical damage.
Refer to the pages written following this symbol.

• VESA and DDC are trademarks of the Video Electronics Standard Association.
•
HDMI
®
, HDMI High-Denition Multimedia Interface
®
and HDMI
®
logo are trademarks or
registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other
countries.
• PJLink trademark and logo are trademarks applied for registration
or are already registered in Japan, the United States of America and
other countries and areas.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
• DICOM® is the registered trademark of the National Electrical Manufacturers Association
for its standards publications relating to digital communications of medical information.
• HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
•
DisplayPort
TM
is trademark owned by the Video Electronics Standards Association (VESA
®
) in
the United States and other countries.
All other trademarks are the properties of their respective owners.
NOTICE This entry notices of fear of causing trouble.
• The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may di󰀨er
from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.

2QM00971-1
Contents
Introduction ............... 3
Features ......................3
Checking the contents of package ....3
Warnings, Cautions, and Notices .....4
Part names ...................16
Projector, Control panel and Indicators,
Ports, Remote control
Setting up ................20
Arrangement ..................2 2
Connecting with your devices .....2 6
Attaching the terminal cover ......3 5
Using the security bar and slot ....3 6
Connecting to a power supply .....3 7
Remote control ............ 39
Installing the batteries ...........3 9
Using the REMOTE ID function ...4 0
Changing the frequency of remote control signal . . 4 0
About the remote control signal ...4 1
Power on/off ..............42
Turning on the power ...........4 2
Turning o󰀨 the power ...........4 3
Operating ................44
Adjusting the volume ...............4 4
Temporarily turning o󰀨 the screen and audio . . 4 4
Selecting an input signal .........4 5
Selecting an aspect ratio .........4 6
Limiting OSD display .............4 7
Adjusting the projector's elevator ....4 8
Adjusting the lens ..............4 9
Adjusting the zoom and focus,
Adjusting the lens position, Lens memory
Correcting the distortion .........5 2
Using the EDGE BLENDING features . . 5 5
Using the magnify feature ........5 9
Temporarily freezing the screen ...6 0
Temporarily shading the screen ...6 0
PbyP (Picture by Picture) /
PinP (Picture in Picture) ...6 1
Using the menu function .........6 5
Indication in OSD, Menu items

EASY MENU. . . . . . . . . . . . . . . 68
PICTURE menu ............70
IMAGE menu ..............74
INPUT menu .............. 77
SETUP menu ..............83
AUDIO menu .............. 91
SCREEN menu............. 92
OPTION menu .............98
NETWORK menu ..........116
SECURITY menu ..........117
Maintenance .............124
Cleaning and replacing the air lter . 12 4
Inserting or replacing the
internal clock battery . .........12 6
Other care ...................12 7
Troubleshooting ..........129
Related messages ..............12 9
Regarding the indicator lamps ...13 1
Resetting all settings ...........13 6
Issues that may be easy to
be mistaken for machine defects . . 13 7
Specications ............146


3QM00971-1
Introduction
Introduction
The projector provides you with the broad use by the following features.
ü The HDMITM/DisplayPortTM/HDBaseTTM ports can support various image
equipment which have digital interface to get clearer pictures on a screen.
ü The super bright light source and high quality optical system can fulll the
demands of professional uses.
ü Optional lens units and a wide range of the lens shift feature provide more
exibility in where you can install the projector.
ü The multiple I/O ports is believed to support any business scene.
ü HDCR and ACCENTUALIZER features are original image stabilizer for a
clearer image.
ü Equipped with an original contrast optimizer function to improve contrast
and vividness.
ü A DICOM® (“Digital Imaging and Communication in Medicine”) provides
simulation mode. This mode simulates the DICOM standard, which is a
standard applicable to digital communications in medicine.
ü COLOR MANAGEMENT corrects an image by dividing it into three-
dimensional space such as color phase, color saturation, and brightness.
Features
• Keep the original packing materials for future shipment. Use the
original packing materials when moving the projector. Remove the lens unit and
attach the lens hole cover when moving the projector.
NOTE
Checking the contents of package
See the Contents of package section in the User’s Manual (concise) which is a
book. Your projector should come with the items shown there. Consult your dealer
immediately if any items are missing.
►Keep small parts away from children and pets. Take care not
to put in the mouth. If swallowed, consult a physician immediately for emergency
treatment.
WARNING

4QM00971-1
Introduction
Warnings, Cautions, and Notices
►Never use the projector if a problem should occur.
• Otherwise it can cause re or electric shock.
• If any of the following abnormalities occur, urgently stop using the product and
unplug it from the power outlet:
- The product is giving o󰀨 smoke or strange smell, or making a strange sound.
- A foreign object or liquid has entered the product.
- The product was impacted by being dropped or hit.
- The product, or the power cord or cables connected is damaged.
• After making sure that the smoke or odor has stopped, contact your dealer.
• The power outlet should be close to the projector and easily accessible. Never
repair the product by yourself because it is dangerous.
►Use special caution for children and pets.
• Incorrect handling could result in re, electrical shock, injury, burn or vision
problem.
• Keep the battery and small parts away from children and pets. Take care that
they should not swallow.
• Install the product away from children and pets. If swallowed, consult a
physician immediately for emergency treatment.
►Do not let any things or any liquids enter to the inside of the product.
• Penetration of liquids or foreign objects could result in re or electrical shock. If
ammable air or liquid goes into the projector, it may cause re or injury due to
explosion caused by catching re.
• Do not put anything wet, small, containing air or liquid around the projector. Do
not use aerosols or sprays to or around the product.
• To avoid penetration of foreign objects, do not put the projector into a case
or bag together with any thing except the accessories of the projector, signal
cables and connectors.
• If liquids or foreign object should enter the projector, immediately turn o󰀨 the
power switch, disconnect the power plug from the power outlet and contact
your dealer.
WARNING
(continued on next page)

5QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Do not get the product wet.
• It could result in a re, an electric shock, and/or malfunction to the projector.
• Do not place the projector near water, such as in a bathroom, kitchen, or
poolside.
• Do not place the projector outdoors or by the window.
►Do not place the projector on an unstable surface. Install the projector in
a stable position. Do not give the projector any shock or impact.
• If the projector should be dropped and/or broken, it could result in an injury,
and continued use could result in re or electrical shock.
• If the projector is shocked, immediately turn o󰀨 the power switch, disconnect
the power plug from the power outlet and contact your dealer.
• Remove all the attachments including the power cord and cables from the
projector when carrying the projector.
• Use the caster brakes placing the projector on a stand with casters.
• For special installation such as ceiling mounting, be sure to consult your dealer
beforehand.
• Install the projector in the way specied in "Setting up", "Arrangement", and
"Adjusting the projector's elevator".
• Do not put the projector on its side, front or rear position.
► Do not place the projector in the following place where oils or chemicals
are used:
- near the kitchen which oil smoke comes from
- oils such as machine oils or aromatic oils are used
- smoke or bubbles for a show or a performance are used
- solvents, medicines, or detergent volatiles or adheres
- corrosive gas is generated
Do not use adhesive such as threadlocker, lubricant and so on.
• Oils adhere to the product due to oil smoke, resulting in re, electrical shock, or
malfunction.
• Degradation of plastic harms the product, resulting in injury, re, electrical
shock, or malfunction due to falling from the ceiling, wall, or high mounted
position.
WARNING
(continued on next page)

6QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Never disassemble and modify.
• The product contains high voltage components and/or laser light-emitting part
beyond the scope of Class 1 (IEC60825-1). Modication and/or disassembly of
the product could result in re, electrical shock, or injury to eyes or skin.
• Do not open or remove any portion of the product unless the manuals direct it.
• For internal maintenance, leave it to your dealer or their service personnel.
►Be cautious of high temperatures of the projector.
• High temperatures are generated when the light source is lit.
• Do not touch the USB wireless adapter while the projector is receiving AC
power.
• If combustibles or aerosol sprays are around the projector, it may cause re or
injury due to catching re or rupture.
• Do not install the projector near thermally conductive or ammable things.
• Do not touch around the exhaust vents during use or just after use, since it is
too hot.
►Never look through the lens or openings when the light source is on.
• A strong light is emitted when the projector’s power is on. Do not look into the
lens and the openings on the projector while the light source is on, since the
projection ray may cause a trouble on your eyes.
► When you turn o󰀨 the projected image while the light source is on,
follow the specied procedure.
• If you wish to have a blank screen while the light source is on, use the BLANK
function.
• Keep any object away from concentrated projection light beam. Blocking the
beam by something causes high temperature and could result in re or smoke.
WARNING
(continued on next page)

7QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Use the accessory cable or a designated type cable for the connection.
• If you use a power cord or a signal cable that are not comply with the
specication, it causes re, electric shock, malfunction, or radio wave
interference.
• Only use the power cord that came with the projector.
• Consult your dealer to properly use connection cables or connectors other than
coming with the projector.
• The power cord that came with the projector is only for this projector. Do not
use it for other devices.
►Clean the power plug by using a soft and dry cloth.
• If dust or metal adheres to or around the AC (power terminal) of this projector
or the power plug, it may cause re or electric shock.
►Insert the power plug into a power outlet rmly.
• Use extra caution when connecting the power cord, as incorrect or faulty
connections may result in re and/or electrical shock.
• Incorrect power supply could result in re or electrical shock.
• Be sure to plug the power cord into an outlet that has specied voltage.
• Avoid using a loose, unsound outlet or contact failure.
• Do not distribute the power supply to multiple devices. It may overload the
outlet and connectors, loosen the connection, or result in re, electric shock or
other accidents.
►Be sure to connect with ground wire.
• Connect the ground terminal of AC inlet of this unit with the ground terminal
provided at the building using the correct power cord; otherwise, re or electric
shock can result.
• If you connect the ground wire to the outlet, it may cause re or electric shock.
WARNING
(continued on next page)

8QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Do not damage the power cord, cables, and connectors.
• If you keep using a damaged the power cord or cables, it can cause a re or
electrical shock.
• If it is damaged, consult your dealer to get a new one.
►Do not touch the power cord with a wet hand.
• It results in electric shock.
►Before cleaning, turn o󰀨 and unplug the projector.
• Neglect could result in re or electrical shock.
• Before cleaning, turn o󰀨 and unplug the projector.
• Take right care of the projector by following the manual.
►Be careful in handling the battery.
• Improper use may result in battery explosion, cracking or leakage, which could
result in re, injury and/or pollution of the surrounding environment. Children or
pets may swallow the battery because it is small.
• If swallowed, consult a physician immediately for emergency treatment.
• If you observe battery leakage, wipe out the leakage and then replace a
battery. If the leakage adheres to your body or clothes, rinse well with water
immediately. If it entered your eye, wash it with clean water immediately and
consult a physician.
• Be sure to use only the specied batteries.
• Do not allow the battery in a re or water. Avoid re or high-temperature
environment. Keep the battery in a dark, cool and dry place.
• Keep the battery away from children and pets.
• Obey the local laws on disposing a battery.
► Do not put anything on top of the projector or hang anything from the
projector.
• Placing anything on the projector could result in loss of balance or falling, and
cause an injury or damage.
• Do not attach nor place anything on the projector unless otherwise specied in
the manual.
WARNING
(continued on next page)

9QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
► Do not place the projector in a place where it can be hot nor block the
projector's ventilation openings.
• The projector may shut down automatically, or may malfunction due to high
internal temperature if it is placed in a place where it can be hot or ventilation
does not operate normally.
• The heat could have adverse inuence on the cabinet of the projector and
other parts.
• Place the projector in a cool place with su󰀩cient ventilation.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
• Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.
• Do not put the projector or the accessories in a microwave oven.
• Do not stop up, block nor cover the projector's vent holes.
• Do not place anything around the projector that could be sucked in or stuck to
the projector's intake vents.
• Do not place the projector on carpet, cushions or bedding.
► Avoid placing the projector in smoky, humid, or dusty place, or in a place
where it can be a󰀨ected by soil salinity.
• Accumulations of dust inside the projector result in re or malfunction.
• Do not place the projector near a smoky, humid or dusty place (ex. a smoking
space, a kitchen, a beach, etc.).
• Do not place the projector near humidiers. Especially for an ultrasonic
humidier, chlorine and minerals contained in tap water are atomized and could
be deposited in the projector causing image degradation or other problems.
• Do not place the projector outdoors.
CAUTION
(continued on next page)

10 QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Avoid Magnetism.
• Magnetic objects may cause interruption of the projector's internal mechanical
performance which may interfere with cooling fans speed or stopping, and may
cause the projector to completely shut down.
• The projector may shutdown automatically or may malfunction if its internal
temperature is too high.
• Avoid any magnetic contact that is not shielded or protected on or near the
projector itself.
► Unplug the projector from the power outlet if the projector is not being
used.
• Unplug the power cord for complete disconnection.
• If you leave the projector with the power cord connected to the outlet, it can
result in a re or an electric shock.
►Do not use the product during electrical storms.
• If the projector is used while a lightning strike occurs, it may result in re or
electric shock.
• If there is a possibility that a lightning strike occurs, stop using the product and
unplug it from the power outlet.
► The designated USB wireless adapter that is sold as an option is
required to use the wireless network function of this projector.
► Before connecting the projector to a network system, be sure to obtain
the consent of the administrator of the network.
• Some networks may have the excessive voltage. Do not connect the LAN port
to any network that might have the excessive voltage.
• You cannot connect this product directly to communication lines (including
public wireless LAN) of telecommunications carriers such as mobile
telecommunications companies, xed-line telecommunications companies, and
internet service providers. When you connect this product to the internet, be
sure to connect it via a router and so on.
CAUTION
(continued on next page)

11 QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Ask your dealer to clean the inside of the projector about every year.
• Accumulations of dust inside the projector result in re or malfunction.
• To ensure the safe use of your projector, ask your dealer to clean and inspect it
about once a year. Do not clean the inside by yourself because it is dangerous.
►Clean the air lter periodically.
• If the air lter becomes clogged by dust and so on, internal temperatures rise
and could cause a re, a burn or malfunction to the projector.
• Use only the air lter of the specied type.
• Do not use the projector without the air lter or the lter cover. It could result in
a re or malfunction to the projector.
• When the indicators or a message prompts you to clean the air lter, clean the
air lter as soon as possible.
CAUTION
(continued on next page)

12 QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Take care not to fatigue your eyes.
• Watching the display continuously for a long time makes your eyes tired.
• Rest the eyes periodically.
►Take care of the lens.
• It may cause breakage, malfunction, or image failure.
• Attach the lens cover to prevent the lens surface being scratched when the
projector is not used.
• Be careful not to scratch the lens with hard objects.
• Use commercially available lens tissue to clean the lens (used to clean
cameras, eyeglasses, etc.).
►Do not directly touch the lens surface with hands.
• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration
of display quality.
►Do not give the remote control any physical impact.
• A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place the projector or heavy objects on the remote control.
►Do not get the remote control wet.
• It may cause a malfunction or battery leakage.
• Do not place the product in a place where it may get wet.
►The remote control uses infrared light to send signals to the projector
(Class 1 LED), so be sure to use the remote control in an area free from
obstacles that could block the remote control’s signal to the projector.
• If the signal transmission of the remote control is blocked, the remote control
may not operate.
NOTICE
(continued on next page)

13 QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Caring for the cabinet and remote control
• Incorrect care could cause not only an injury but adverse inuence such as
discoloration, peeling paint, etc. Take right care of the projector according to
the following.
• Wipe lightly with gauze or a soft cloth.
If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner
diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a
soft, dry cloth.
• Do not use an aerosol sprays, solvents, volatile substances or abrasive
cleaner.
• Do not allow long-term close contact with rubber or vinyl.
• Before using chemical wipes, be sure to read and observe the instructions.
►Keep the original packing materials for future reshipment.
• Be sure to use the original packing materials when moving the projector.
• Use special caution for the lens.
►Set the sound volume at a suitable level to avoid bothering other people.
• It is better to keep the volume level low and close the windows at night to
protect the neighborhood environment.
NOTICE
(continued on next page)

14 QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Characteristics of the projector
• Positional deviation or distortion of a projected image, or shift of the focus
may occur due to ambient conditions, and so on. They tend to occur until the
operation becomes stable, especially within about 30 minutes after the light
source is turned on. Check and readjust them as necessary.
►About consumables
• Light Source, LCD panels, polarizers and other optical components, and air
lter and cooling fans have a di󰀨erent lifetime in each. These parts may need
to be replaced after a long usage time.
• This product is not designed for continuous use of long time. In the case of
continuous use for 6 hours or more, or use for 6 hours or more every day
(even if it is not continuous), or repetitious use, the lifetime may be shortened,
and these parts may need to be replaced even if one year has not passed
since the beginning of using.
►Image characteristics
• This projector is a projection device using liquid crystal panel. The display
condition of the projector (such as color, contrast, etc.) depends on
characteristic of the screen because the projector uses a liquid crystal display
panel.
• Do not use a polarized screen. It can cause red image.
►Be careful of printing of the LCD panel. (for LCD models only)
• This projector is a projection device using liquid crystal panel. If the projector
continues projecting a still image, inactive images or 16:9 aspect images in
case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.
►About bright spots or dark spots
• This projector is a projection device using liquid crystal panel. Although bright
spots or dark spots may appear on the screen, this is a unique characteristic
of liquid crystal displays, and it does not constitute or imply a machine defect.
NOTE
(continued on next page)

15 QM00971-1
Introduction
Warnings, Cautions, and Notices (continued)
►Be careful of condensation.
• It is not a malfunction even if a projected image becomes blurred or cannot
be seen due to condensation of internal lens or mirror when the projector
is moved out of a room with a low temperature to a room with a high
temperature.As the projector adapts to the ambient temperature, condensation
is gone and the projected image goes back to normal.
►Noise of cooling fans
• The projector has the function that controls the rotation speed of cooling fans
adjusting to the conditions of use. When the temperature around the projector
is high, cooling fans rotate faster and becomes noisier.
►Connecting with notebook computer
• If you connect this projector and a notebook computer, you need output the
display to an external monitor, or output simultaneously to the internal display
and an external monitor. Refer to the manual of your notebook computer for
details.
►Using the security bar and slot
• The security bar and slot is not comprehensive theft prevention measures. It is
intended to be used as supplemental theft prevention measure.
NOTE

16 QM00971-1
Introduction
Part names
Projector
(1) Filter cover (124)
The air  lter and intake vent
are inside.
(2) Elevator feet (x2) (48)
(3) Remote sensors (x2) (41, 110)
(4) Lens hole cover
(5) Indicators (17)
(6) Intake vents
(7) Control panel (17)
(8) AC (AC inlet) (37)
(9) Exhaust vents
(10) Ports (18)
(11) Security bar (36)
(12) Security slot (36)
(13) Safety bar (36)
(14) Battery cover (126)
►Do not open or remove any portion of the projector, unless
the manuals direct it.
►Do not subject the projector to unstable conditions.
► Do not apply a shock or pressure to this projector. Remove all the attachments
including the power cord and cables, from the projector when carrying the projector.
►Do not look into the lens and the openings on the projector while the light
source is on as the projection ray may cause a trouble on your eyes.
►Keep any object away from concentrated projection light beam. High
temperatures are generated when the light source is lit. Blocking the beam
causes high temperature and could result in  re or smoke.
WARNING
►Do not approach or touch the lens or the ventilation
openings while using the projector or for a while after using it to prevent a
burn. Take care of ventilation.
►Do not place anything around the lens and ventilation openings of the projector.
►Do not attach anything onto the lens except the lens cover of this projector
because it could damage the lens, such as melting the lens.
CAUTION
(continued on next page)
(1)
(3) (2)
(4)
(5)
(12)
(8)
(11)
(14)
(7)
(6)
(2)
(9) (10)
(9)
(6)
(6)
(6) (13)

17 QM00971-1
Control panel and Indicators
(1) STANDBY/ON button (42)
(2) INPUT button (45, 65)
(3) MENU button (65)
(4) LENS SHIFT button (50)
(5) ZOOM button (49)
(6) FOCUS button (49)
(7) SHUTTER button (60)
(8) SERVICE indicator (134, 135)
(9) STATUS indicator (132 ~ 134)
(10) FILTER indicator (133)
(11) LIGHT indicator (134)
(12) TEMP indicator (134, 135)
(13) POWER indicator (42, 131 ~ 135)
Introduction
Part names (continued)
(continued on next page)
(3)
(2)
(7)
(1)
(8) (9) (10) (11) (12) (13)
(6)
(5)
(4)

18 QM00971-1
Ports (26 ~ 34)
(1) COMPUTER IN port
(2) HDBaseT port
(3) LAN port
(4) WIRELESS port
(5) HDMI 1 port
(6) HDMI 2 port
(7) DisplayPort port
(8) VIDEO port
(9) 3G-SDI port
(10) AUDIO IN1 port
(11) AUDIO IN2 (L, R) ports
(12) AUDIO OUT port
(13) MONITOR OUT port
(14) REMOTE CONTROL IN port
(15) REMOTE CONTROL OUT port
(16) CONTROL port
(17) HDMI OUT port
Introduction
Part names (continued)
(1)
(2)
(3)
(15) (13)
(8)
(16)
(5) (6)
(7)
(10)
(11) (12) (14)
(9)
(4) (17)

19 QM00971-1
Introduction
Part names (continued)
• When you press the button marked with *1, the input signal selection
menu is displayed.
• Any button marked with *2 is not supported on this projector (130).
• Each time you press any button (except ID buttons), the ID button of current
selected ID number lights (40).
NOTE
Remote control
(1) STANDBY button (43)
(2) ON button (42)
(3) ID - 1 / 2 / 3 / 4 buttons (40)
(4) COMPUTER 1 button (45)
(5) COMPUTER 2 button *1
(6) VIDEO button (45)
(7) LAN button (45)
(8) USB TYPE A button *1
(9) USB TYPE B button *1
(10) HDMI 1 button (45)
(11) HDMI 2 button (45)
(12) DisplayPort button (45)
(13) HDBaseT button (45)
(1 4) SDI button (45)
(15) DIGITAL button *1
(16) FOCUS + / - buttons (49)
(17) ZOOM + / - buttons (49)
(18) AV MUTE button (44)
(19) LENS MEMORY LOAD / SAVE buttons (51)
(20) SHIFT button (50)
(21) OSD MSG button (47)
(22) ▲/▼/◄/►cursor buttons
(23) ENTER button (65)
(24) RESET button (65)
(25) MENU button (65)
(26) GEOMETRY button (52)
(27) PICTURE button (71, 72)
(28) NETWORK button
(29) INTERACTIVE button *2
(30) FREEZE button (60)
(31) PbyP button (61)
(32) MAGNIFY ON / OFF buttons (59)
(33) VOLUME + / - buttons (44)
(34) INFO button (35) ASPECT button (46)
(36) MY BUTTON - 1 / 2 / 3 / 4 buttons (101, 102)
(37) Battery cover (39) (38) Wired remote control port (33)
Back of
the remote control
(1)
(3)
(4)
(7)
(8)
(10)
(13)
(14)
(16)
(20)
(18)
(23)
(24)
(26)
(30)
(34)
(36)
(2)
(5)
(6)
(9)
(11)
(12)
(15)
(17)
(19)
(21)
(22)
(25)
(29)
(33)
(37)
INFO
NETWORK
INTERACTIVE
(27) (28)
(38)
(31) (32)
(35)

2 0 QM00971-1
Setting up
Setting up
Install the projector according to the
environment and manner the projector will be
used in.
This projector will perform in a free tilt
angle, as shown in the gures below.
For the case of installation in a special
state such as ceiling mount, the specied
mounting accessories and service may be
required. Before installing the projector,
consult your dealer about your installation.
Tilt 360°
Horizontal 360° Vertical 360° (combination of
horizontal and vertical)