Hitachi Travelstar 5K320 User manual

Page 1 version 1.0
Quick Installation Guide
Hitachi Travelstar 5K320
Models: HTS543232L9A300 HTE543232L9A300
HTS543225L9A300 HTE543225L9A300
HTS543216L9A300 HTE543216L9A300
HTS543212L9A300 HTE543212L9A300
HTS543280L9A300 HTE543280L9A300
HTS543232L9SA01
HTS543225L9SA01
HTS543216L9SA01
HTS543212L9SA01
HTS543280L9SA01
Handling precautions
Set the drive down gently to prevent damage from impact or vibration.
Handle the drive carefully by the edges. Do not touch the exposed printed circuit board or any electronic components.
Do not press on the top or bottom of the drive.
Before handling the drive, discharge any static electricity from yourself and your clothing. With one hand touch an
unpainted metal surface, then touch the ESD bag with the other hand. Remain in contact with the chassis and the bag
for a minimum of two seconds.
Vibration, shock and static electricity to the drive will damage the precision parts. In particular, prevent vibration or
shock generated by dropping, knocking over or hitting the drive. Also, avoid touching the electrical components
directly, which can discharge electrostatic energy and damage the drive.

Hitachi Global Storage Technologies
Page 2 version 1.0
Mounting Recommendations
The mounting hole locations and size of the drive are shown below:

Hitachi Global Storage Technologies
Page 3 version 1.0
The drive will operate in all axes (six directions) and will stay within the specified error
rates when tilted ±5 degrees from these positions. Performance and error rate will stay
within specification limits if the drive is operated in the other permissible orientations from
which it was formatted. Thus a drive formatted in a horizontal orientation will be able to
run vertically and vice versa.
The recommended mounting screw torque is 0.3±0.05 Nm.
The recommended mounting screw depth is 3.0±0.3 mm for bottom and 3.5±0.5 mm for
horizontal mounting.
The user is responsible for using the appropriate screws or equivalent mounting hardware
to mount the drive securely enough to prevent excessive motion or vibration of the drive at
seek operation or spindle rotation.

Hitachi Global Storage Technologies
Page 4 version 1.0
Interface connector
The figure below shows the physical pin location
All pins are in a single row, with a 127 mm (0.050”) pitch.
The comments on the mating sequence in Table in the section 7.3 apply to the case of
back-plane
blind-mate connector only. In this case, the mating sequences are:(1)the ground pins
P4 and P12;(2) the pre-charge power pins and the other ground pins; and (3) the
signal pins and the rest of the power pins.
There are three power pins for each voltage. One pin from each voltage is used for
pre-charge in the backplane blind-mate situation.
If a device uses 3.3V, then all V33 pins must be terminated. Otherwise, it is optional
to terminate any of the V33 pins
If a device uses 5.0V, then all V5 pins must be terminated. Otherwise, it is optional to
terminate any of the V5 pins
If a device uses 12.0V, then all V12 pins must be terminated. Otherwise, it is optional
to terminate any of the V12 pins.

Hitachi Global Storage Technologies
Page 5 version 1.0
© 2008 Hitachi Global Storage Technologies
Produced in the United States 2/08
All rights reserved
Travelstar is a trademark of Hitachi Global Storage
Technologies.
Hitachi Global Storage Technologies’ trademarks are
authorized for use in countries and jurisdictions in which
Hitachi has the right to use, market and advertise the brands.
The Travelstar trademark is authorized for use in the Americas,
EMEA and the following Asia-Pacific countries and
jurisdictions: Australia, Hong Kong, Japan, New Zealand,
South Korea and Taiwan. Contact Hitachi for further
information. Hitachi Global Storage Technologies shall not be
liable to third parties for unauthorized use of Hitachi Global
Storage Technologies trademarks.
References in this publication to Hitachi Global Storage
Technologies’ products, programs, or services do not imply
that Hitachi intends to make these available in all countries in
which it operates. Some countries have laws that may affect
encryption-enabled devices. Hitachi GST assumes no
responsibility for compliance with laws that apply to our
products after they are sold or outside of our control.
Accordingly, we suggest that you review all laws of the
countries where you conduct business.
Product specifications provided are sample specifications and
do not constitute a warranty. Information is true as of the date
of publication and is subject to change. Actual specifications
for unique part numbers may vary. Please visit the Support
section of our website, www.hitachigst.com/support, for
additional information on product specifications. Photographs
may show design models.
26 February 2008