Hitachi Travelstar 80GN User manual

Handling precautions
yWear a grounded wrist strap while handling the drive
to prevent damage from Electrostatic Discharge
(ESD).
ySet the drive down gently to prevent damage from
impact or vibration.
yDo not open the ESD bag containing the drive until
needed.
yHandle the drive carefully by the edges. Do not
touch the exposed printed circuit board or any
electronic components.
yDo not press on the top or bottom of the drive.
yDo not cover the drive’s breather hole.
Quick installation
Installation of this Hitachi Travelstar drive in some note-
books may require use of unique hardware (such as
mounting trays, connecting cable, insulating material). If
you are uncertain if hardware is needed, consult your
notebook manufacturer as this operation may require a
qualified technician.
Back up all data before proceeding with installation.
1. Set the jumpers
yMaster drive. No jumper is required if the drive is
the only drive in a system or the Master drive in a
two-drive system.
ySlave drive. If this is the Slave drive in a system,
place a jumper in setting A2. (See the A2 setting in
the illustration.)
yCable Select. Setting A3 in the illustration. Consult
the system manual to see if your computer supports
Cable Select.
Jumper settings
A1. A2. A3. A4. A5.
Pin 1
A1. Master A2. Slave A3. Cable Select
A4 & A5. Never attach a jumper in these positions!
2. Attach the drive
For assistance on the physical installation of the drive,
consult your system manual.
3. Configure the computer
1. Turn on the computer.
2. Enter Setup.
3. Go to Hard Disk Drive Configuration.
4. Select Autodetect if it is available.
5. If Autodetect is not available, set to User and set to
appropriate parameters from the table below.
6. Save the settings and exit.
7. Reboot the system from a floppy disk.
2063116,383C25T020ATMR04
3063216,383C25T030ATMR04
4063216,383C25T040ATMR04
6063316,383C25T060ATMR04
8063416,383IC25T080ATMR04
Capacity
(GB)
Sectors/
Track
HeadsCylindersModel Number
Quick installation guide
Hitachi Travelstar 80GN
2.5 inch ATA/IDE hard disk drive
IC25N020ATMR04
IC25N030ATMR04
IC25N040ATMR04
IC25N060ATMR04
IC25N080ATMR04
Models:
page 1 version 1.0

4. Partition and format
Partition and format the drive using either of these two
methods:
yDisk Manager 2000
i. Boot the Disk Manager 2000 installation utility
ii. If the Disk Manager 2000 configuration matches
your new system configuration, continue. If the
system configuration is not a match or if you
want to proceed manually, select no. Then
verify the BIOS settings, cabling, and jumpers.
Run Disk Manager 2000 again.
iii. Disk Manager 2000 determines available parti-
tion sizes based on the operating system to be
installed. Select the partition sizes for your
installation.
iv. Click “Finish” to complete the partitioning and
formatting of your drive.
yFDISK.EXE and FORMAT.EXE (or a similar parti-
tioning software from the operating system)
Follow the instructions provided with your operating
system to partition the drive. If FDISK.EXE recog-
nizes only 8.4 GB of a drive, the BIOS may not
support Interrupt 13 Extensions.
Format the drive by following the instructions pro-
vided with FORMAT.EXE. Formatting will verify the
hard disk media and create file allocation tables for
the partition.
5. Boot up the computer
If the system does not boot up after the installation of the
drive, check all the settings. If the system still fails to
boot up, contact the Hitachi Global Storage
Technologies Support Center.
© Copyright Hitachi Global Storage Technologies
Hitachi Global Storage Technologies
5600 Cottle Road
San Jose, CA 95193
Produced in the United States
3/03
All rights reserved Deskstar™ is a trademark of Hitachi
Global Storage Technologies.
Microsoft, Windows XP, and Windows are trademarks
of Microsoft Corporation in the United States, other
countries, or both.
Other product names are trademarks or registered
trademarks of their respective companies.
References in this publication to Hitachi Global Storage
Technologies products, programs or services do not
imply that Hitachi Global Storage Technologies intends
to make these available in all countries in which Hitachi
Global Storage Technologies operates.
Product information is provided for information
purposes only and does not constitute a warranty.
Information is true as of the date of publication and is
subject to change. Actual results may vary.
This publication is for general guidance only.
Photographs may show design models.
12 March 2003
Hitachi Global Storage Technologies
page 2 version 1.0