HITROL HCC-95P Series User manual

HCC-95P Series
HITROL CO.,LTD. 1
HITROL CO., LTD.
HEAD OFFICE.FACTORY.R&D INSTITUDE
HITROL CO., LTD 141, Palhakgol-gil, Jori-eup
Paju-si, Gyeonggi-do, Korea
TEL. : [phone]
FAX. : [phone]
www.hitrol.com
INSTRUCTION MANUAL
CAPACITANCE TYPE LEVEL SWITCH
HCC-95P Series
Doc. no.: HCC95P_IM_Eng_Rev.1
Issue date: 2021. 08

HCC-95P Series
HITROL CO.,LTD. 2
You should be careful where CAUTION is
marked to carry out the work.
You should be aware of where NOTICE is
marked to carry out the work.
You should be well-informed of the contents
where WARNING is marked before carrying
out the work.
Table of Contents
Overview ······························3
Characteristics ···························3
Operating Principle & Composition ··········3
Specification ····························4
Dimensions & Technical Data ···············5
Installation ·····························7
Precautions for Installation ·················7
Precautions for Attachment ················8
Wiring ······························8
Failure Check & Maintenance ··············9
Precautions for Removal ··················9
Precautions for Use ····················9
Precautions for Inserted External Wire ······9
Precautions for Grounding ··············10
Safety and Environment ··················10
Marking ····························11
User Training ··················11
Warranty and Contact ····················11
APPENDIX
APPENDIX U ···········M-95P User Manual

HCC-95P Series
HITROL CO.,LTD. 3
Overview
Characteristics
Operating
Principle &
Composition
HCC-95P(-Ex) Series is a capacitance type level switch and it detects a level of medium
by sensing of capacitance value change by dielectric constant of each medium.
Where an air surrounding the electrode probe is replaced by other medium, the
capacitance value is changed according to the dielectric constant of the medium. Once
the electrode probe is touched by the medium, the capacitance value is increased and
the level switch activates relay output by converting of the changed capacitance value to
the electronic signal.
C: Capacitance of Medium
C1: Capacitance of Initial State
R : Conductivity of Medium
[Operating Principle Reference Figure]
■Widely used for various type of medium such as solid, powder, and liquid
■Semi-permanent life cycle due to moveless parts
■Easy to use in corrosive liquid
■Easy installation for wire type (HCC-95PW)
■Operating can be checked at the site.
■Various probe types can be applied according to installation condition
■Explosive proof version and Dust proof version (HCC-95P-Ex)
Housing
Process Conn.
Inactive Rod
Insulation
Sensing Probe
Module
(M-95P)

HCC-95P Series
HITROL CO.,LTD. 4
Specification
Model
HCC-95P
HCC-95PH
HCC-95PW
HCC-95PWH
Probe Type
Rod(Flat)
Rope
Mounting
Screw or Flange
Ambient temperature
-20°C ~ +60°C
Process temperature
-40°C~+80℃
-40°C~+150℃
-40°C~+80℃
-40°C~+150℃
Process Pressure
Vacuum~ 20kg/cm2(300#)
Power Source
AC 90~240V, 50/60Hz / DC +24V
Output Signal
DPDT
Contact Rating
AC 250V, 5A / DC 30V, 5A
Enclosure
Weather-Proof (IP65)
Wetted Parts Material
SUS 304, 316L with Teflon(Peek)
SUS 304, 316L with Teflon
Process Connection
PT 1”(M) Screw
Housing; Cable Entry
PBT;PF1/2”(F),IP65
AL;PF1/2”(F),IP66
PBT;PF1/2”(F),IP65
AL;PF1/2”(F),IP66
AL;PF1/2”(F),IP66
AL;PF1/2”(F),IP66
Model
HCC-95P-Ex
HCC-95PH-Ex
HCC-95PW-Ex
HCC-95PWH-Ex
Probe Type
Rod(Flat)
Rope
Mounting
Screw or Flange
Ambient Temperature
-20°C ~ +60°C
Process Temperature
-40°C~+80℃
-40°C~+150℃
-40°C~+80℃
-40°C~+150℃
Process Pressure
Vacuum~ 20kg/cm2(300#)
Power Source
AC 90~240V, 50/60Hz (Std.) / DC +24V (Opt.)
Output Signal
DPDT
Contact Rating
AC 250V, 5A / DC 30V, 5A
Enclosure
Ex d IIC T5/T6(*), IP66
Ex tb A21 IP66 80℃
Ex d IIC T3/T4(*), IP66
Ex tb A21 IP66 150℃
Ex d IIC T5/T6(*), IP66
Ex tb A21 IP66 80℃
Ex d IIC T3/T4(*), IP66
Ex tb A21 IP66 150℃
Wetted Parts Material
SUS 304, 316L with Teflon(Peek)
SUS 304, 316L with Teflon
Process Connection
PT 1”(M) Screw
Housing; Cable Entry
AL. ; PF 1/2”(F), IP66
(*) Explosion-proof Fluid Temp. & Grade: Max. 70℃for T6
Max. 80℃for T5
Max. 130℃for T4
Max. 150℃for T3
Weather-proof Version
Ex-proof Version

HCC-95P Series
HITROL CO.,LTD. 5
Actual product may have a tolerance slightly.
Dimensions & Technical Data
The dimensions on the following pages are indicated in [mm].
Rod Type
Material: Aluminum
Rod Type
■Connection Type
-Screw: PT 1”(Std.), NPT 1”, PF 1”, Others
-Flange: ANSI, JIS, DIN
-Tri-Clamp
■Material
-SUS 316L, Others
Active Rod
material:
316L with
Teflon
Active Rod
material:
316L with
Teflon
Rope
material: 316
Weight material:
C.S, 316L
[Housing]
[Connection]
[Probe]
High Temp. Version
High Temp. Version
Material: Aluminum
For Liquids
For Solids
Inactive Rod
material:
316L with
Teflon
Inactive Rod
material: 316L
Active Rod
material: 316L
Inactive Rod
material: 316L
Rod Type
(Fully insulated w/ TEFLON)
Insulation
material:
Teflon
Insulation
material:
Teflon
Material: PBT
Active Rod
material: 316L
Rope Type
Flat Type
* Flat Type can be used in liquids, but further verification is required at the head office as a sample.

HCC-95P Series
HITROL CO.,LTD. 6
Dielectric Constant Value
Air
1
Nitrogen, Liquid
1~2
Fuel Oil (Gasoline, Diesel……)
2
Hydrogen Chloride
4.6~12
Hexane, Liquid
6
Butanol
17~18
Ammonia
16~25
Alcohol
16~31
Acetone
20
Caustic Soda
22~26
Ethanol
25
Methanol
32~33
Glycerin
47~68
Water
81
Sulfuric Acid
84
The data of dielectric constant value can be downloaded from technical data by accessing our website. www.hitrol.com
For Liquids
For Solids
Rod Probe
Rod Probe
Fully insulated
w/ TEFLON
Rod Probe
Rope Probe
Total length(L)
100~2,500
300~1,000
100~2,500
Min. 1,000, Max. 10,000
≤2,500
≤4,500
>4,500
Active Rod Length
(L-L1)
100~1,000
150~500
100~1,000
-
Inactive Rod
Length(L1)
~1,500
150~500
~1,500
-
Active Rod dia.
Ф15
(including Teflon)
Ф28
(including Teflon)
Ф15
(including Teflon)
-
Inactive Rod dia.
Ф25.4
Ф28
(including Teflon)
Ф25.4
-
Weight
A
-
-
-
170
300
300
B
-
-
-
Ф28
Ф28
Ф40
For acid liquids
-
O
-
-
For high-viscosity
liquids
O
O
-
-

HCC-95P Series
HITROL CO.,LTD. 7
Installation
Precautions
for
Installation
- If more than one level switch is installed in a tank, the distance between each probe
shall be at least 300mm apart. (If the distance between probes is short, it may be
affected by the interconnection of the instrument, causing unstable operation.)
- For side mounting installation, an inactive rod shall be located at least 50mm inside of
tank, and it is recommended that the probe be tilted by 15 degrees to the horizontal
surface. (A foreign object between the nozzle and the probe may cause malfunction.)
- Probe shall be installed to avoid the inlet side of the measuring instrument, and the
protector shall be installed to prevent damage to the probe. Protector shall have
sufficient area to protect the sensor from incoming medium and be installed at a
distance that does not affect sensor operation.
- For side mounting installation, the cable entry shall be installed facing the ground to
maintain the waterproof function.
- When installing on the low level, carefully install the dead stock and material bridge.
- If the medium in the tank is liquid, set the Time Delay appropriately to delay the
operation of the output relay.
- For outdoor installation, it is recommended to install the sun cover to avoid the effects
of temperature increases.
- In case of tank with stirrer, the probe shall be installed at a safe distance from the
stirrer.
The capacitance type level switch can be installed in screw (PT, NPT, PF, etc.) and flange
(ANSI, JIS, DIN, etc.) as well as tri-clamp and other various locations.
Pay attention to the following matters during installation.
■Side Mounting Installation
Highly sensitive measurement is available because it measures the level by whole of
probe but it shall be installed slopingly, forwarding of sensor to the bottom in order to
avoid a malfunction caused by build-up of the medium on the sensing probe.
■Top Mounting Installation
This installation is not much affected by build-up of the medium on the probe but the
sensitivity is lower than side mounting because it measures the level by the end of probe
only, and it is not suitable to detect a level of the medium which has a low dielectric
constant.

HCC-95P Series
HITROL CO.,LTD. 8
Precautions
for Attachment
Wiring
■Connect correctly AC(90~240V) or DC(+24V) power to the power specification.
■Make sure to connect the DC power with correct polarity(+, -).
■Do not connect the wire with the power connected.
■It provides DPDT output by default, wired COM and N.O terminals when using the
high alarm.
■External grounding shall be completed.
In case of Ex-proof products, apply the power after tightening the cover after wiring.
■When installing the sensor, avoid shaking or obstacle.
■Do not install in openings that are prone to severe fluid flow, mechanical damage, or
chattering.
■Check the specification of temperature and pressure generated inside the tank.
■Condensation may occur if the temperature of the housing differs significantly from the
ambient temperature, so dehumidifier shall be filled or ventilated(gortex) before use.
■Connect the flanges or bolts with the same specifications.
■Make sure to insert gaskets between flanges. (Select the gaskets in consideration of
the temperature of the content and the pressure inside the container.)
For Ex-proof products, it shall be installed with an appropriate grade for environment.

HCC-95P Series
HITROL CO.,LTD. 9
If there is an atmosphere of explosive gas, do not open the cover of the product.
Make sure that it is not subject to any high impact while moving.
Failure Check
& Maintenance
Precautions
for
Removal
Precautions
for
Use
Precautions
for Inserted
External Wire
(Ex-proof)
■Check the level and presence of measure object in the tank before removing it.
■Wear gloves when removing it, to prevent a burn.
■Unlock the lock key before removing the cover. (Ex-proof)
■Disassemble work shall be done with the power off.
■Make sure that any O-ring or gasket is not damaged while opening or closing the
cover of product.
■Check whether the product would be installed in the Ex-proof zone, and use the
appropriate product.
■Do not bend or extend the sensor randomly.
■Make sure to install the product and the cover first before supplying the power.
■Do not use if the temperature range of the installation exceeds -20℃to +60 ℃.
■Do not use if the protection grade requires a higher grade than its product. (IP66 for
AL. Housing or IP65 for PBT Housing)
■Do not use where vibration is present.
■Use the cable gland connection or metal pipe line lead-in on the wire inlet, and use a
product with equivalent Ex-proof certificate to connect it with the external line lead-
in method.
■For non-use external wire inlet, use a closed plug that passes safety certificate above
equivalent performance with the product.
The life span of key parts depends on user’s environment and can be used optimally
through periodic check. Therefore, regular inspection ensures optimal performance of
product, so take regular inspection and maintenance at least every year. Inspection of the
appearance of the product shall be visually checked to see if there is any damage, and the
attachment of the medium or foreign substances to the sensor will make it worse, so they
shall be removed regularly. Be careful not to damage Teflon part during removal.
■Failure Check
1) Is power voltage connected correct?
2) Is power voltage supplied according to specifications correct?
3) Is cable wiring correct?
4) Is the Fail-Safe Mode setting correct?
5) Does the green LED turn on?
Turn off the power of the product for maintenance.
In an explosion area, do not disassemble when power is applied.

HCC-95P Series
HITROL CO.,LTD. 10
Precautions
for Grounding
(Ex-proof)
Safety and
Environment
■The grounding has an external and an internal grounding. When connecting to an
external ground, the ground wire shall be 4㎟(4mmSQ). (The internal grounding shall
be wiring to the same specification as the connected cable.)
■Precautions for Use
- Make sure to connect the product and vessel using required tools for sure.
- Keep the lock key safe and make sure that it is locked.
- Do not apply high impact to the product.
■Precautions for Wiring
- Make sure to connect contacts with the correct terminals. (Refer to Wiring)
- Wire and supply the power to the device after checking the specifications.
- Incorrect power voltage may cause damage to the product.
- Pay attention to prevent electric shock.
■Disposal of Product
- Make sure to separate the amplifier and main unit from housing before disposing
the products.
- No part (ex. Mercury switch) has influence on the environment, so no special
attention is required.
HEAD External Grounding (PBT)
HEAD External Grounding (AL.C)
External Grounding
4㎟(4mmSQ)
Make sure to insert a washer if the terminal lug is removed from ground
terminal and then re- connected. (Loosening prevention)

HCC-95P Series
HITROL CO.,LTD. 11
Marking
User
Training
Warranty
and Contact
■Warranty and Service
This product is subject to the warranty for 2 years of shipment and unpaid service will
be provided for any damage found under normal operating conditions. If it is not about
the failure of product, the service charge will be payable.
You can request A/S at our website or by contacting our headquarters.
■Headquarters ․Factory ․Laboratory Contact Number
ADDRESS: HITROL CO., LTD 141, Palhakgol-gil, Jori-eup, Paju-si, Gyeonggi-do, Korea
T E L : 031-950-9700 (Headquarters & A/S)
F A X : 031-943-5600 (Headquarters & A/S)
■Product Identification
- The product identification mark is attached onto the housing and shows the
model name, serial number, working temperature, working pressure, and matters
regarding output. The serial number is a unique manufacturing number for the
identification of products.
<Ex-proof Version>
Under the aforementioned, the temperature of fluids in the tank where the product is used
shall not be exceed 80℃for general type and 150℃for high-temperature type. In addition,
make sure that the ambient temperature of housing is kept at -20 - +60℃. In the case of
an explosion-proof type product, never open the cover of the product during use. Ex-proof
products are designed according to Article 34 of the Industrial Safety and Health Act
and Article 58.4 of the Enforcement Rules of the same Act.
<Weather-proof Version >
Do not apply a Non-ex-proof product in an Ex-proof zone. Ex-proof products can
only be installed at zone 1 and 2 of locations where explosive gas atmosphere
exists. It shall be installed in compliance with the ex-proof temperature rating
and the applied fluid temperature.

M-95P
User Manual
Capacitance Type Level Switch
Doc. no. : Rev2.0
APPENDIX U

1. Configuration of Module (M-95P)
No
Configuration
Function
1
S Key
■Function setting
■Save the setting
2
M Key
■Mode change
■Cancellation
3
▲Key
■High Set
■Setting the value up
4
▼Key
■Low Set
■Setting the value down
5
LCD
■Display of operating and setting status
6
LED
■Display of power and status
7
Power
■For supply power (AC / DC)
8
Frame Ground
■FG
9
Relay Out
■Relay Contact Out (DPDT)
1
2
3
4
5
6
7
9
8

2. Specification
Category
M-95P
Enclosure
Weather Proof
Material
PBT / AL.C
Mounting
COMPACT
Microprocessor
16Bit Microprocessor
Supply Voltage
AC Free (90V ~ 240V @ 50/60Hz)
DC+17V ~ +35V @ Typ.+24V
Power Consumption
AC Free
(90~240V)
Stand-by
■AC220V @ 7W
■AC110V @ 3.1W
Active
■AC220V @ 7.6W
■AC110V @ 3.9W
DC+24V
Stand-by
■DC+24V @ 0.2W
Active
■DC+24V @ 0.96W
Measurement Accuracy
±1mm
Oscillation Frequency
1MHz
Sensitivity Resolution
0.1pF
Dielectric Constant
2 @ Min. (Powder/Liquid)
Frame Ground
FG
Relay Delay Time Range
0.5Sec. @ Min / 1Sec.~ 10Sec. @ 0.1Sec Resolution
Relay Contact Out Control
Normal Open @ Default
Relay Contact Rating
DPDT : AC250V/5A, DC30V/5A
Status Indicator
Tri-Color LED [ Green / Red / Orange ]
Setting Method
Setting Menu
Display
C, H, L, A↔B, Rotation, Setting, Lock
Ambient Temperature
-20℃~ +80℃

3. Configuration of Setting Menu
No.
Contents
Description
[02]
Low Value Set
Set the Low value by viewing the current Capacitance value
[03]
High Value Set
Set the High value by viewing the current Capacitance value
[08]
Relay Contact Type
N.O or N.C (Default : N.O)
[09]
Relay Delay Time Set
0.5 ~ 10 sec. (Default 0.5 sec @ 0.5 sec Step ADJ.)
[11]
LOW Capacity fine Adjustment
Find adjustment from settled capacitance value.
(0.1%, 1%, 10%)
[12]
HIGH Capacity fine Adjustment
[30]
Rotation Time Set
0.5 ~ 10 sec. (Default 3 sec @ 0.5 sec Step ADJ.)
[31]
'C' Display On/Off
Rotation ‘C’select display
(Current Capacitance value)
[32]
'H' Display On/Off
Rotation ‘H’select display
(High Capacitance setting value)
[33]
'L' Display On/Off
Rotation ‘L’select display
(Low Capacitance setting value)
[34]
'A↔B’Display On/Off
Rotation ‘A↔B’select display
(Relay Contact Type & ON/OFF)
[90]
Error Number Output
Display of error number according to malfunction
[91]
Capacity value Output
Low, High, display current Capacitance value
[100]
Reset
Reset the all setting

4. M-95P LOCK Turn off/Setting Way
※When power is applied, the initial screen shows Relay Contact Type,
Lock status. ( When in the LOCK state, the key does not respond. )
■Key LOCK Turn off
- , , , Press for approximately 1 second at the same time
to release.
- In the photo, the cursor bar under the lock disappears.
■Key LOCK Setting
- , , , Press for approximately 1 second at the same time
to set it up.
( Set in the unlocked state. )
- When locked, it automatically switches to relay display mode.
- In the photo, a cursor bar is displayed under the lock.
■Display mode automatic switching
- If the button key is not pressed, it automatically switches to the
LOCK state after counting 30 seconds.
- If you press the button key along the way, the count will resume
after initialization.
- It does not switch when setting the SET Menu.
Lock State

5. Setting and Operating
■LCD configuration
■The cursor moves sequentially whenever the button is pressed.
■The order of movement is as follows.
C H L A↔B C H …
■Into the Setting Menu
■Press the button to move the display screen to Setting Mode.
■In the Setting Mode, press button for 1 second then the green LED
will be flickering and you can go into the Setting Menu.
■Return to Setting Menu
■In the Setting Menu, press button for 1 second then the green LED
will be flickering and you can go back to the Setting Mode.
About 1 sec
Display mode
Cursor
Segment
Bar graph
About 1 sec

■Select the Setting Menu
■In the Setting Menu, use / button to select the user setting function.
■Pressing button for 1 second will enter the function.
Key Button
Function
Press shortly
Increasing numerical value
Press shortly
Decreasing numerical value
Press more than 1 sec
Save and Leave
Press more than 1 sec
Leave without Save
/ Press

6. SETTING Way
■HIGH Auto SETTING
■, , When pressed at the same time for about 1 second,
The LED turns on and off and the value is set.
■Because the initial value is OFF, setting the current value to HIGH
Changes to ON and the LED keeps blinking.
■LOW Auto SETTING
■, , When pressed at the same time for about 1 second,
the LED turns on and off and the value is set.
■Since the initial value is OFF, if the current value is set to a LOW value,
the LED stays on while maintaining the OFF state.
■Auto Setting and confirm
1. Press to confirm C(current value), H(High value), and L(Low value).
2. If the value of C is higher than H, the Relay ON status LED keeps blinking.
3. If the value of C is lower than L, the Relay OFF status LED is ON.

■Manual SETTING
■SETTING Condition : HIGH value ≥LOW value
■HIGH value < LOW value : LED RED is briefly turned on and off witho
■LOW Manual SETTING
■Enter item 2 in Setting Mode.
■The value displayed on the LCD is the current Capacitance value.
■When the desired value is reached, press the button for
About 1 second to save it.
■For safe operation, set it to 0.1% greater than the current value..
■HIGH Manual SETTING
■Enter item 3 in Setting Mode.
■The value displayed on the LCD is the current Capacitance value.
■When the desired value is reached, press the button for
About 1 second to save it.
■For safe operation, set it to 0.1% less than the current value.
About 1 sec
About 1 sec