Hitron HDG-N15DPV2A7U User manual

PRODUCTION RELEASE & REVISION
REV DESCRIPT'N/BUYER DWG No PARTS No. BY CHK DATE
TITLE
SIZE REV.
SCALE
MATERIAL
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS ARE IN MM.
- TOLERANCE
LABEL +/- 3
MANUAL +/- 5
GUIDE +/- 5
COLOR
DATE
DRAWN
CHKED
APPROVALS
PARTS LIST
DESCRIPTION/MATERIAL
ITEM QTY
A4
DO NOT SCALE
2C
Manual Instruction
50303763
NOTES
1.MODEL:HDG-N15DPV2A7U/ NO BRNAD
2.MATERIAL: 2
모조지100g/m WHITE
3.COLOR: BLACK
4.SIZE:105(+/-5)mm x 148(+/-5)mm
5.LABEL: -------------
3
전자
강영구
105(+/-5)mm
148+/-5)mm
J.Y.LIU
M.J.KWON
K.H.JUNG
A INITIAL ------------------- 50303763 J.Y.LIU M.J.KWON 06-16-M14
15-06-12
3-AXIS PLASTIC
DOME CAMERA
Mega Analog Plastic
Dome Camera
15-06-12
15-06-12
15-06-12
B INITIAL ------------------- 50303763 J.Y.LIU M.J.KWON 06-25-M14
rev.B - 6,11,13,14,19 페이지내용변경, 재고소진후 적용
rev.C - 22p Rs485-Fastrax삭제
C INITIAL ------------------- 50303763 J.Y.LIU M.J.KWON 15-06-12

3-AXIS PLASTIC
DOME CAMERA
Mega Analog Plastic
Dome Camera

2
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
CAUTION : Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
WARNING : This is a Class A poduct. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
FCC INFORMATION : This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.. Do not block any ventilat ion openings. Install in accord ance with the manufacturer`s
instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the ca rt, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
9. CAUTION - THESE SERVICING IN STRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ON LY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
10. Use satisfy clause 2.5 of IEC60950-1/UL 60950-1 or Certified/Listed Class 2
power source only.
11. Indoor use only.
EXPLANATION OF GRAPHICAL SYMBOLS
IMPORTANT SAFETY INSTRUCTIONS
3
LIMITATION OF LIABILITY
THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL
RESPECTS, HOWEVER, WE CANNOT ASSUME RESPONSIBILITY FOR ANY
CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION
CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR NEW
EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH CHANGES.

TABLE OF CONTENTS
4
INTRODUCTION 5
CONNECTIONS 6
INSTALLATION 7
SETUP MENU 11
SPECIFICATIONS 22
EXTERNAL DIMENSION 23
VIDEO OUT CHECK 21
LENS ADJUSTMENT 21
DC IRIS LENS 21
CONTENTS & PACKAGE 6

The 1/3" HD CMOS camera, especially for closed circuit television CCTV and
security surveillance application.
High performance SONY 1/3" Exmor CMOS
WDR(Wide Dynamic Range)/BLC(Back-light compensation)
Auto Electronic Shutter [1/60(1/50) ~ 1/50,000] and manual electronic shutter modes
1.0 lux(COLOR), 0.1 lux(B/W)
Day & Night (ICR) :Auto / Color / BW / EXT
Smart IR
Privacy mask Function (8zone)
Motion Detection
Defog
HLMASK
Use Certified / Listed Class 2 power source only
Operates in DC12, AC24V ± 10%
5
TM
Auto and manual white balance modes (ATW/AWC/Manual/AWB)
OSD (on screen display)
DNR (Digital Slow Shutter)

6
1. Lens : 2.8-12mm D/N A/I Vari-focal lens for wide area monitoring.
2. Power : 24V AC Input / 12V DC Input
(IR Model 7Watts)
3. Video : BNC connector used to connect the camera to a monitor, switcher, etc.
RS 485(+)
DN EXT-IN
AC24V/DC12V
AC24V/DC12V
RS 485 (-)
GRAY
SKY BLUE UTP+(Option)
PINK UTP-(Option)
BLACK GND
Power source from a DC 12V 10% or AC 24V 10% 60/50Hz ± 1Hz
Use Certified/Listed Class 2 power source only.
± ±

7
Surface mount

Locking flap's
Screws(x3)
Locking flap(x3)
8

(Fig. 4)
9
2

Locking flap's
Screws(x3)
Locking flap(x3)
4
10

11
RESET
WHITE BAL
BACKLIGHT
SENS-UP
D-WDR
<WHITE BAL>
OFF
WDR
BLC
HSBLC
<BACKLIGHT>
ATW
AWC->SET
INDOOR
OUTDOOR
MANUAL
AWB
<DAY&NIGHT>
SHARPNESS
LSC
D-EFFECT
DIS
D-ZOOM
SMART D-ZOOM
RETURN
CAM TITLE
MONITOR
CVBS CROP
VIDEO OUT
LANGUAGE
VERSION
RETURN
<RESET>
FACTORY
RETURN
EXT
RS485
DEFECT DET

12
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
MANUAL
OFF
ATW
AUTO
1)
2)
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
SHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
RETURN
AUTO
|▪l▪▪▪▪| 15
OFF
|▪l▪▪▪▪| 30
OFF
OFF
RET
< EXPOSURE > MODE
AGC, SENS-UP, BRIGHTNESS,
D-WDR and DEFOG function of the camera.
It
1/50000, x2 ~ x30
Adjust the Auto Gain Control level. ▶ 0 - 15
AGC
3) SENS-UP Select the Digital Slow Shutter level. ▶ OFF, AUTO (x2 ~ x30)
BRIGHTNESS Adjust the BRIGHTNESS level. ▶ 0 - 100
D-WDR
DEFOG
Select the Digital WDR.▶ ON, OFF
ON, OFF
POS/SIZE
GRADATION
DEFAULT
Adjust the window position & size
Off, Low, Middle, High
Initialize the setting values

13
BACKLIGHT
The BACKLIGHT menu is used to the ability to expand the dynamic range and to prevent back
lighting from the image.
1)WDR Select the Dynamic Range level.
* When WDR is ON, D-WDR, D-ZOOM, SMART D-ZOOM
and DIS function can not turn on.
2)BLC Prevents such a back light effect to secure a clear image under All illumination
environments.
Adjust the size of Back Light Compensation area.
3)HLMASK Mask the high light zone with specific color & level.
Adjust the window position & sizeAREA
Initialize the setting valuesDEFAULT
Select the HLMASK area ▶ AREA1 - AREA4SELECT
Adjust the HLMASK area window position & sizeDISPLAY
Select the HLMASK level 0 ~ 100▶ LEVEL
All Day, NightMODE
Initialize the setting values.DEFAULT
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
WDR
GAIN
WDR OFFSET
RETURN
LOW
|▪▪▪▪▪| 0
RET
BLC
GAIN
AREA
DEFAULT
RETURN
MIDDLE
RET
HLBLC
SELECT
DISPLAY
LEVEL
MODE
BLACK MASK
DEFAULT
RETURN
AREA
ON
|▪▪l▪▪| 30
ALL DAY
ON
RET
< BACKLIGHT >
Select the BLC gain ▶ Low, Middle, HighGAIN

14
WHITE BALANCE
The screen color can be adjusted by using the Auto White Balance function.
It compensates for deviations in the white color caused by changes in the color temperature of
the light source so that the colors are reproduced correctly.
1)ATW
2)AWC->SET
3)INDOOR
4)OUTDOOR
5)MANUAL
Automatically adjust color temperature.
Automatically readjust only by pressing AWC→SET.
Set the color temperature to 3200°K
Set the color temperature to 6300°K
Manual mode.
User can change Red and Blue gain value manually.
BLUE
RED
0 ~ 100
0 ~ 100
6)AWB Automatically extended range of color temperature adjustment.
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
MANUAL
BLUE
RED
RETURN
| I | 50
|▪▪I▪▪| 50
RET
▪▪ ▪▪
< WHITE BALANCE > MODE

15
.
CDS
BURST ON, OFF
IR SMART LEVEL 1~15
AREA Adjust the window position & size.
DAY&NIGHT mode are changed according to the brightness of the image.
Use only when the camera is installed in a dark place but the camera is viewing a bright place.
When used in a normal installation, hunting may occur.
< DAY&NIGHT > MODE
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
D&N AUTO
DELAY
D N (CDS)
N D (CDS)
RETURN
| I | 5
|▪▪I▪▪| 70
|▪▪I▪▪| 40
RET
▪▪ ▪▪
D&N B&W
BURST
IR SMART
RETURN
ON
ON
RET
3) EXT
D&N change depending on the external input device.

16
The IMAGE menu provides the ability to adjust the SHARPNESS, LSC, D-EFFECT, DIS, D-ZOOM
and SMART D-ZOOM functions of the camera.
1) SHARPNESS Adjust the SHARPNESS level. ▶ 0 - 15
2) LSC Select the lens Lens Shading Compensation. ▶ ON, OFF
3) D-EFFECT FREEZE Select real or still mode ▶ ON, OFF
MIRROR Select OFF, MIRROR, V-FLIP, ROTATE
NEG. IMAGE Select Negative image mode ▶ ON, OFF
4) DIS Select the Digital Image Stability ▶ ON, OFF
5) D-ZOOM Adjust the Digital Zoom level. ▶ x1.0 - x62.0
* When D-ZOOM is ON, SMART D-ZOOM and DIS function can not turn on.
6) SMART D-ZOOM Adjust the Smart Digital Zoom area, level, sensitivity and time.
* When D-ZOOM is ON, D-ZOOM and DIS function can not turn on.
SELECT Select the Smart D-zoom Area ▶ AREA1, AREA2
DISPLAY Select the Smart D-zoom Area display ▶ ON, OFF
SENSITIVITY Adjust the Smart D-zoom Sensitivity ▶ 0 - 60
D-ZOOM Adjust the Digital Zoom level ▶ x1.0 - x62.0
TIME Adjust time level ▶ 0 - 15 (sec)
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
IMAGE
SHARPNESS
LSC
D-EFFECT
DIS
D-ZOOM
SMART D-ZOOM
RETURN
| I | 8
OFF
OFF
OFF
OFF
OFF
RET
▪▪ ▪▪
<SMART D-ZOOM>
SMART D-ZOOM
SELECT
DISPALY
SENSITIVITY
D-ZOOM
TIME
DEFAULT
RETURN
AREA1
ON
|▪▪▪I▪| 60
x2.8
|▪I▪▪▪| 3
RET
IMAGE
SHARPNESS
LSC
D-EFFECT
DIS
D-ZOOM
SMART D-ZOOM
RETURN
| I | 8
OFF
OFF
OFF
OFF
OFF
RET
▪▪ ▪▪

17
1) DNR
2D
3D
SMART NR
Select Digital Noise Reduction.
LEVEL
▶ ON, OFF
▶ ON, OFF
▶ ON, OFF (Sensitivity 0 - 100)
Adjust the 3DNR level ▶ 0 - 100
2) MOTION
SELECT
DISPLAY
SENSITIVITY
Detects the Motioned Object in the image. ▶ ON, OFF
MOTION VIEW
DEFAULT
Select the Motion area ▶ AREA1 - AREA4
Adjust the Motion area window position & size
Adjust the Motion sensitivity level ▶ 0 - 60
Select the Motion view ▶ ON, OFF
Initialize the setting values
3) PRIVACY
SELECT
DISPLAY
COLOR
Hide an area you want to hide on the screen.
TRANS
DEFAULT
Select the privacy zone ▶ AREA1 - AREA8
Adjust the Privacy window type, position & size
▶ OFF, INV., MOSAIC, COLOR
Select the privacy zone color ▶ 0 - 15
Select the privacy zone transparency ▶ 0 - 3
Initialize the setting values
4) DEFECT DET
LIVE DPC
STATIC DPC
START
Compensates for bad pixels.
LEVEL
SENS-UP
Select the Live DPC mode ▶OFF, ON, AUTO
▶ ON, OFF
Start the bad pixels correction
Select the Static DPC level ▶ 0 - 60
Select the Sens-up level ▶ x2 - x30
AGC Select the AGC level ▶ 0 - 8
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
FUNCTION
DNR
MOTION
PRIVACY
DEFECT DET
RETURN
OFF
OFF
< >FUNCTION

18
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
FUNCTION
DNR
MOTION
PRIVACY
DEFECT DET
RETURN
OFF
OFF
RET
<DNR>
<MOTION>
DNR
2D
3D
RETURN
ON
ON
OFF
FUNCTION
DNR
MOTION
PRIVACY
DEFECT DET
RETURN
OFF
OFF
RET
MOTION
SELECT
DISPLAY
SENSITIVITY
MOTION VIEW
DEFAULT
RETURN
AREA1
ON
|▪▪▪▪▪| 60
ON
RET
FUNCTION
DNR
MOTION
PRIVACY
DEFECT DET
RETURN
OFF
OFF
RET
< >PRIVACY
PRIVACY
SELECT
DISPLAY
COLOR
TRANS.
DEFAULT
RETURN
AREA1
COLOR
2
3
RET
FUNCTION
DNR
MOTION
PRIVACY
DEFECT DET
RETURN
OFF
OFF
RET
< >DEFECT DET
DEFECT DET
LIVE DPC
STATIC DPC
RETURN
AUTO
ON
RET
FUNCTION
DNR
MOTION
PRIVACY
DEFECT DET
RETURN
OFF
OFF
RET
STATIC DPC
START
LEVEL
SENS-UP
AGC
RETURN
| |
x8
|▪▪▪▪▪| 0
RET
▪I▪▪▪ 4
DEFECT DET
CLOSE THE IRIS
THEN
PRESS SET KEY
DEFECT DET
WAITING...
<FUNCTION>

19
SYSTEM
The IMAGE menu provides the ability to adjust the CAM TITLE, RS485, MONITOR, CVBS CROP,
VIDEO OUT, LANGUAGE and, VERSION functions of the camera.
1) CAM TITLE Maximum of 15 characters are allowed.
3) MONITOR
LCD
GAMMA
ADAPT. LEVEL
Select the Monitor type ▶ LCD, CRT
BLUE GAIN
RED GAIN
Select the Gamma level ▶ AUTO, USER. USER+Y, 0.45 -1.0
Adjust the Adaptive level ▶ 0 - 100
Adjust the Blue gain level ▶ 0 - 100
Adjust the Red gain level ▶ 0 - 100
4) CVBS CROP ▶ ON, OFF
CRT
BLACK LEVEL
BLUE GAIN
RED GAIN
Select the Black level ▶ -30 ~ +30
Adjust the Blue gain level ▶ -50 ~ +50
Adjust the Red gain level ▶ -50 ~ +50
5) VIDEO OUT Select the video out type ▶ NTSC, PAL
6) LANGUAGE OSD menu LANGUAGE (16ea) ▶ ENGLISH etc.
7) VERSION Firmware VERSION
< >SYSTEM
MAIN MANU
LENS
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
RESET
EXIT
DC
OFF
ATW
AUTO
< >CAM TITLE
CAM TITLE
0 1 2 3 4 5 6 7 8 9
A B C D E F G H I J K
L M N O P Q R S T U V
WXYZ▶→ ← ↑ ↓ ()
¯ － _■ /=& : ~ , .
← → CLR POS END
________________
SYSTEM
CAM TITLE
RS485
MONITOR
CVBS CROP
VIDEO OUT
LANGUAGE
VERSION
RETURN
OFF
LCD
OFF
NTSC
ENGLISH
1.0
RET
2) RS485
CAM ID
ID DISPLAY
BAUD RATE
Select the CAMERA ID ▶ 0 ~ 255
Select the CAMERA ID position ▶ OFF, ON
Select serial communication speed
▶ 2400, 4800, 9600, 19200, 38400 BPS
SYSTEM
CAM TITLE
RS485
MONITOR
CVBS CROP
VIDEO OUT
LANGUAGE
VERSION
RETURN
OFF
LCD
OFF
NTSC
ENGLISH
1.0
RET
If you see a part color scene out of the white is Blue, Red gain to
adjust the color alignment.
Note