HMS AnyBus-PCI Profibus DPV1 Slave Manual

Installation Leaflet - AnyBus-PCI Profibus DPV1 Slave
Rev 1.03 - Part no. SP0780
Web: www.anybus.com HMS Industrial Networks AB
AnyBus-PCI Profibus DPV1 Slave
Package Contents
The AnyBus-PCI Profibus DPV1 Slave package consists of the following items:
Anybus-PCI Profibus DPV1 Slave card
This installation leaflet
CD-ROM containing software drivers, SDK and documentation
PCI Card Overview
Status LED:s
Warning!
The AnyBus-PCI Profibus DPV1 Slave card contains ESD (Electrostatic Discharge) sensitive components. Be sure
to observe ESD precautions when installing the card; do not touch any circuits or connectors, and handle the card
only by its edges.
#Indication State Meaning
1 Active Off PCI card not active
Green PCI card active (i.e. Transport Path open)
2 Application Led - Controlled by software (ABS_SetApplicationLed())
3 Acyclic Traffic Off No power or no DPV1 request currently being executed
Green A DPV1 request is currently being executed
4 Fieldbus Diagnostics Off No diagnostics present or no power on the module
Red, Flashing 1Hz Error in configuration data
Red, Flashing 2Hz Error in parameter data
Red, Flashing 4Hz Profibus ASIC initialisation error
5 Fieldbus On Line Off Bus is not online, or now power on the module
Green Bus is on line and data exchange is possible
Green, Flashing Clear mode
6 Fieldbus Off Line Off Bus is off line
Red Bus is off line, or no power on the module
1
3
5
2
4
6
PCI Edge Connector
Status LED:s
Profibus Connector
(reserved)

Installation Leaflet - AnyBus-PCI Profibus DPV1 Slave
Rev 1.03 - Part no. SP0780
HMS Industrial Networks AB Web: www.anybus.com
Software Driver Installation
1. Double click on ‘Setup.exe’.
(This file will be executed automat-
ically when inserting the supplied
software CD-ROM provided that
the AutoPlay feature is enabled.)
2. Click ‘Browse’ to select a different
installation path, or click ‘Next’ to
start the installation process.
3. A progress bar will illustrate
progress of the installation.
4. Finished.
Shut down the computer and pro-
ceed with the hardware installation
steps described on the following
pages.
Important:
• It is strongly recommended to perform the software installation prior to installing the PCI card into the PC. This
ensures that the software drivers are available when the card is detected by the system.
• Administration rights are required when installing the drivers on windows NT, 2000 or XP.
• To avoid software conflicts, make sure that no other AnyBus-PCI drivers are installed in the system (e.g. the
CoDeSys drivers)
!

Installation Leaflet - AnyBus-PCI Profibus DPV1 Slave
Rev 1.03 - Part no. SP0780
Web: www.anybus.com HMS Industrial Networks AB
Hardware Installation
1. Unplug AC power and remove system cover
2. If present, remove the bracket opposite the PCI slot. Keep the screw for later use.
3. Align the card connector with the slot and press firmly until the card is completely seated
4. Secure the card connector to the chassis using the screw removed earlier
5. Re-attach the system cover and AC power
Warning!
Unplug the AC power when adding or removing expansion cards or other system components. Failure to observe
this may result in physical injury or damage to computer components.
Important:
To ensure trouble-free operation, the front plate of the card must be screwed together with the system cover. The
system cover must also be grounded in compliance with local regulations.
!

Installation Leaflet - AnyBus-PCI Profibus DPV1 Slave
Rev 1.03 - Part no. SP0780
HMS Industrial Networks AB Web: www.anybus.com
Technical Specification
Recommended Profibus connectors:
• Profibus Plug 180, order number 6GK 1500-0FC00, from www.siemens.com
• Profibus Max standard, part number 134928, from www..erni.com
General
• Half length 33Mhz PCI card
• 3.3 & 5V support (Universal keyed add-in)
•Plug&Play
• Interrupt or Polled operation
• 0 to +55C operating temperature
System Requirements
• Windows NT 4.0 SP3 or higher or
above,Windows 98, Windows 2000, Win-
dows ME, or Windows XP
• 486 DX 66 or higher recommended
• 16 MB RAM (32 MB recommended)
• 256-color SVGA (800x600) display
•CD-ROMdrive
•AvailablePCI-slot
• Mouse or tablet
Software
• Supports the AnyBus-S API
(SDK included)
• Multiple AnyBus PCI cards supported
• .GSD-file for Profibus configuration tool
included on CD
Profibus Interface Details
• Optically isolated Profibus RS485 interface
• Supports Class 1 & Class 2 services
• Node ID set via fieldbus or by software
• Automatic baud rate detection
• Cyclic I/O size up to 244 bytes in/244
bytes out
• Up to 416 bytes total I/O
EMC Compliance
• Emission: EN 61000-6-4:2001
• Immunity: EN 61000-6-2:2001
•CEmarked

Installation Leaflet - AnyBus-PCI Profibus DPV1 Slave
Rev 1.03 - Part no. SP0780
Web: www.anybus.com HMS Industrial Networks AB
Support
HMS Sweden
Email: [e-mail]
Phone: +46 (0) 35 - 17 29 20
Fax: +46 (0) 35 - 17 29 09
Online: www.anybus.com
HMS America
Email: [e-mail]
Phone: [phone]
Fax: [phone]
Online: www.anybus.com
HMS Germany
Email: [e-mail]
Phone: [phone]
Fax: [phone]
Online: www.anybus.com
HMS Japan
Email: [e-mail]
Phone: [phone]
Fax: [phone]
Online: www.anybus.com
Profibus User Organization
Technical questions regarding the Profibus
fieldbus system should be addressed to your
local Profibus User Organization.
Online: www.profibus.com
Downloads
Manuals, .GSD-files, software drivers etc., are
available for download at ‘www.anybus.com’