Hobby Components HCRFID0002 User manual

©Hobby Components Ltd
RFID Access Control Panel
Manual
HCRFID0002
Product Specification
Voltage: 12VDC+10%, Current 1.2A
Lock Relay: 12VDC/2A
Environmental Temperature: working:0℃~45℃;
storage:-10℃~55℃
Relative humidity: working: 40%~90%RH;
storage: -20%~90%RH
Card Capacity: 1000
PIN Capacity: Public PIN: 1 Private PIN:500
Internal Reader Frequency: ID model:125KHz
ICmodel: 13.56MHz
Proximity Card: ID model: EM or compatible
IC model: Mifare1 or compatible
Card Reading Distance: ID model:5 - 15CM
IC model: 3 - 5CM
Lock interface: Relay output or level output
Exit Button: One interface
Bell: One interface
Door contact: One interface
Alarm Interface: One level output
Factory Defaults
Programming Pin: 990101
Door Open Mode: Card or public (1234)
Private Pin: 0000
Door Open Time: 3 Seconds
Anti-Break Alarm: Disabled
Door Contact Alarm: Disabled
Lock Status: Disabled
Alarm Delay: 0 Seconds
Modify Private Pin: Disabled
LED & Buzzer
Normal mode:
Valid command: Short beep
Invalid command: Long beep
Programming mode:
Green LED on
Valid command: Two short beeps
Invalid command: Three beeps
Cancel Command
Press the [*] key to cancel command.
Functions and Setup
Enter the programming mode
Press [*]+[6-digit pin] (Default is 990101)
Modify the programming pin
Press [0]
+[new 6-digit pin]
+[confirm the new 6-digit pin]
Enroll card
Press [5]
+[3-digit index code] (2 beeps)
+[Card1] (beep, 2 beeps)
+[Card2] (beep, 2 beeps)
+……
+[Cardn] (beep, 2 beeps)
+[*] (2 beeps)
3-digit index code: range from 001-500. Card can be deleted
by this code.
When enrolling multiple cards, every card index code will be
calculated in order. For example, card one’s index code is 15,
card two’s will be 16.
The default private pin for each card is 0000
Delete card
Delete by index code
Press [7]
+[3-digit code1] (2 beeps)
+[3-digit code2] (2 beeps)
+……
+[3-digit coden] (2 beeps+[*](2 beeps)
Delete by presenting card
Press [7]
+[Presenting Card1] (beep, 2 beeps)
+[Presenting Card2] (beep, 2 beeps)
+……
+[Presenting Cardn] (beep, 2 beeps)
+[*] (2 beeps)
Delete all cards
Please restore the factory default
The private pin will be deleted when the card is deleted
Exit programming mode
Press [*] (2 beeps)
Set up door open mode
Card or pin mode
Press [1]+[0] (2 beeps)
Card + private pin mode
Press [1]+[1] (2 beeps)
PINs
The pin in “Card or PIN” mode is either the public pin or
private pin (at most 500).
Disable changing private pin
Press [1]+[2] (2 beeps)
Enable changing private pin
Press [1]+[3] (2 beeps)
Change private pin
Press [＃] (2 beeps)
+[Presenting card] (beep,2 beeps)
+[4-digit old pin] (2 beeps)
+[4-digit new pin]
+[confirm the new pin] (2 beeps)

©Hobby Components Ltd
Change public pin
Press [3]+[4-digit pin] (Default 1234)
When the public or private pin is 0000, the pin is void in
“Card or pin” mode.
Change door open time
Press [2]+[TT]
TT is the time interval in seconds. For example, if the door
open time is 3 seconds, then TT=03.
Anti-break
Disable anti-break: Press [4]+[0]
Enable anti-break: Press [4]+[1]
Door contact sensor
Disable door sensor: Press [6]+[0]
Enable door sensor: Press [6]+[1]
Door sensor alarm
Disable alarm: Press [8]+[0]
Enable alarm: Press [8]+[1]
After turning on this function, the controller will give off
continuous long beep when the door is not closed after normal
opening, or the door is not opened through the controller.
Alarm delay time
Press [82]+[TT].
TT is the time interval in seconds. For example, if the delay
time is 3 seconds, then TT=03.
When door is locked TT seconds, if the door contact sensor
is in alarm status, the controller is in alarm mode. This function
should be used when the door sensor alarm is on.
Restore factory default
Press [86]. There will be 2 beeps, 3 beeps and 3 beeps
after 5 seconds, then the factory defaults are restored.
User’s instruction
Card or PIN mode
The pins should be entered in 2 seconds
Press [*] key to cancel pin input
Card + Private PIN mode
[Reading card]+[enter 4-digit pin] to open
Press [*] key to cancel pin input
Reset programming pin
Short the J2 on controller to reset the programming pin to
factory default.
FAQ
Symptom
Possible solutions
After the lock is opened,
there are 8 short beeps
The controller needs higher voltage; the power
supply should be checked.
The card reading distance
is short or card cannot be
read
1. If the controller is on metal surface, it should
be moved to other place.
2. Check the power supply.
After reading card, there
are 3 beeps and lock is
not open
1. It’s in card+pin mode.
2. [＃] key is pressed, wait for 5 seconds to
present the card.
The enrolled card cannot
open the door
1. Check if the door sensor is in alarm status.
2. Disable the door sensor alarm.
Press [*]+[Programming
pin] there is long beep
and cannot enter the
programming mode
Other keys are pressed before pressing the [*]
key. Keep on pressing [*] key after long beep,
then enter the programming mode again.
Press [＃] key, there is a
long beep, the private pin
cannot be changed
Other keys are pressed before pressing the [*]
key. Keep on pressing [*] key after long beep,
then press the [*] key again.
Press [5],there are 3
beeps
The controller has full card capacity.
Press [5]+[index code], 3
beeps
This index code is in use, select another index
code.
Press [5]+[index code] 2
beeps +[presenting card]
3 beeps
This card is in use.
The controller exit
In programming mode, if there is no input in 20
seconds, the controller exits programming mode
programming mode
automatically.
Wiring
With normal power supply
DOOR
To door contact
The other end to DGND
DGND
POENSW
To exit button
The other end to DGND
PUSH/NO
To GND of the fail-safe
lock
The other end off the lock to ＋
12VDC
NC
To GND of the fail-open
lock
The other end off the lock to ＋
12VDC
GND
To the GND of power
supply
+12VDC
To the +12V of power
supply
BELL
To door bell
BELL
To door bell
JP3
Short JP3
JP2
Short 1,2
With access control power supply
DOOR
To door contact
The other end to DGND
DGND
POENSW
To exit button
The other end to DGND
PUSH/NO
To PUSH on power
supply
Lock should be wired to power supply’s
NC and GND.
NC
GND
To the GND of power
supply
+12VDC
To the +12V of power
supply
BELL
To door bell
BELL
To door bell
JP3
Do NOT short JP3
JP2
Short 2,3