Hobby king Assaultreaper 500 User manual

collective pitch 3D quadcopter

INSTRUCTION MANUAL

Specification:

TYPE: Collective Pitch Electric 3D Quadcopter

Rotor Diameter: 118MM

Length:635 MM

Width: 365 MM

Weight: 986g w/out battery

Flying weight : 1240g w/battery

1.0 Important Information

Table of Contents

The Assault Reaper 500 3D is not a toy, this Multirotor utilizes high-tech components

and technologies to provide superior performance in flight. Improper use of this

product can result in serious injury or even death. Please read this manual carefully

before use and be conscious of your own personal safety and the safety of others

when operating this product. HobbyKing / the seller assumes no liability for the

operation or use of this product.

This product is intended for use by experienced pilots aged 14 years or more. Any

minors wishing to fly this product must be accompanied by a responsible adult.

When selecting a flying site for this product please be sure to obtain the relevant

permission from the owner before flying. HobbyKing accept no liability for any safety

duties or fines rising from operation, usage and misuse after purchase of the product.

(1)

(2)

(3)

1.0 Important Information 1

3-13

16-21

4.0 Main Controller Set Up Guidelines

5.0 Brushless Speed Controller Set Up

6.0 T-SIX Radio Settings

7.0 Binding the Transmitter and Receiver

9.0 Aerobatic Flight Settings

3.0 Assault Reaper 500 3D Assembly

2.0 Assault Reaper 500 3D Set up Instructions

8.0 Normal Flight Settings

Rotor1 (Clockwise)

Servo 1

Front

Back

Servo 4

Leading Edge

of the blade

Leading Edge

of the blade

Servo 2

Servo 3

Rotor3 (Clockwise) Rotor2 (Counter-Clockwise)

Rotor4 (Counter-Clockwise)

Leading Edge

of the blade

Leading Edge

of the blade

2.0 Assault Reaper 500 3D Set Up Instructions

Front

Servo 1

Servo 4

3.0 Assault Reaper 500 3D Assembly

No.1 Front Pulley Block Assembly

(1) Slide the drive belt through the left and right fixed tubes respectively.

(2) Face the fixed tube gap downwards, secure to the front pulley block,

and tighten the fixing screw.

Face the fixed

tube gap down

Right fixed tube

M2x8 screw

Left fixed tube

Drvien belt

M2 fixing nut

Front pulley block

Servo 2

Servo 3

Back

No.2 Back Pulley Block Assembly

(1) Slide the drive belt through the left and right fixed tubes respectively.

(2) Face the fixed tube gap downwards, secure to the back pulley block,

and tighten the fixing screw.

Face the fixed

tube gap down

Right fixed tube

M2x8 screw

Left fixed tube

Drvien belt

M2 fixing nut

Back pulley block

Front

M2x8 screw

M3x3 screw

M2 fixing nut

NO.3 Front End Assembly Drive Shaft And Middle

Fixed Tube

(1) Place the front end of the drive shaft through the drive wheel

and bearing, tighten the fixing screw on the flat position.

(2) Fit the middle fixed tube to the front pulley block,

and tighten the fixing screw.

Notice: The Flat section of the shaft is to be connected to the

front end of the airframe as illustrated.

Middel fixed tube

Flat position

Driven shaft

Driven wheel

Back

M2x8 screw

M3x3 screw

M2 fixing nut

Middel fixed tube

Driven shaft

Driven wheel

NO.4 Rear End Assembly Drive Shaft and Middle Fixed Tube.

(1) Slide the back end of the drive shaft through the

drive wheel and bearing, tighten the fixing screw on

the second flat position.

Second flat position

First flat position

(2) Fit the middle fixed tube to the back pulley block,

and tighten the fixing screw.

Back

M3x3 screw

M3x10 screw

NO.5 Main Drive Gear and Brushless Motor Assembly.

(1) Fit the main drive gear onto the drive shaft, and tighten the fixing

screw on the flat position.

(2) Fit the brushless motor to the back pulley block, move it up and down

until the main drive gear and motor mesh smoothly, then tighten the

fixing screw to secure.

Motor gear

Main driven gear

Rotor1

Rotor2

Rotor3

Rotor4

Front

Back

NO.6 Instructions For Drive Belt Assembly

(1) The arrows represent the rotation direction.

(2) When assembling the drive belt try to keep it tight to avoid vibration

in operation.

Rotate the end of the drive belt 90 degrees

counter-clockwise when assembled.

Rotate the end of drive belt 90

degrees counter-clockwise when

assembled.

Rotate the end of the drive belt 90 degrees

clockwise when assembled.

Rotate the end of driven belt 90

degrees clockwise when assembled.

Back

PB2x8

PB2x10

PB2x14

M2x6

PB2x8

Rotor2

M2x14 screw

NO.7 Rotor 2 / Rotor 4 Assembly

(1) Install the drive belt to Rotor 2, ensure the rotation is correct.

(2) Install Rotor 2 front and rear seat, and tighten the fixing screw.

(3) Install Rotor 4 in the same manner as Rotor 2.

Front fixed seat

Driven belt

Back fixed seat

Control the swing arm

Back

Rotor3

M2x14

PB2x10

PB2x14

PB2x8

M2x6

NO.8 Rotor 1 / Rotor 3 Assembly

(1) Install the drive belt to Rotor 3, ensure the rotation is correct.

(2) Install the Rotor 3 front and rear fixed seat, and tighten the fixing screw.

(3) Install Rotor 1 in the same manner as Rotor 3.

Front fixed seat

Driven belt

Back fixed seat

Control the swing arm

90°

No.9 Pull Rod Assembly

Pull rod

(2) Connect the pull rod joint buckle to the ball end, the

propeller PITC should be at an angle of 0 degrees.

Once the steering servos have been positioned to

centre, the steering gear control swing arm must be

positioned at an angle of 90 degrees to ensure correct

operation.

(1)

If necessary adjust this accordingly.

PA2x11

M3x14

M3x14 screw

KB2x5

Front

Back

Leading Edge

of the blade Leading Edge

of the blade

Leading Edge

of the blade

Leading Edge

of the blade

KB2x5

No.10 Reinforcing Plate, Skid Landing and Propeller Assembly.

M3 fixing nut

(1) Install the reinforcing plate to the bottom of the front back pulley block.

(2) Install the bottom cover and skid landing to the bottom of the front,

back pulley block.

(3) Install the propeller into the propeller clip according to the rotation.

Reinforcing plate

Skid landing

Bottom cover

No.11 ESC, Main Controller, Receiver, Battery,

Canopy Assembly

(1) Install the ESC to the backend of the mount plate.

(2) Install the main controller to the mount plate.

(3) Install the receiver to the mount plate.

(4) Install the battery to the mount plate.

(5) For wiring diagrams please refer to 4.0: main controller port instructions

and 5.0: ESC instructions.

(6) Fix the canopy to the support beam.

Canopy

Canopy support beam

Battery

Receiver

Main controller

Brushless ESC

Back

Front

11 12 13

4.0 Main Controller Set Up Guidelines

7 8

910

AUX1 IN: connect to receiver AUX1 port Servo 1: connect to servo 1

Servo 2: connect to servo 2 Servo 3: connect to servo 3

Servo 4: connect to servo 4 THRO OUT: connect to ESC

RUDD IN: connect to receiver RUDD port

AILE IN: connect to receiver AILE port

THRO IN: connect to receiver THRO port

ELEV IN: connect to receiver ELEV port

ELEV G.S: Lift (front and back) gyroscope sensitivity adjustment knob, to increase by clockwise (+), Will increase the front and back

balance effect of the fuselage (fuselage steady is the best); reverse to reduce the balance effect.

AILE G.S：Aileron (left and right) gyroscope sensitivity adjustment knob, to increase by clockwise (+), Will increase the left and right

balance effect of the fuselage (fuselage steady is the best); reverse to reduce the balance effect.

ELEV/AILE EXT：Lift (front and back)/Aileron (left and right) Servo stroke ATV adjustment knob, to increase by clockwise (+), servo

became more sensitive; reverse is more slow.

Setting mode switch: WK is flight mode; ADJ is debug mode, can not fly in this mode.

Black——Yellow

Brushless Motor

Blue——Green

Red——Red

5.0 Brushless Speed Controller Set up

Connect to main controller

THRO OUT port

Connect to battery

Attention: The brushless motor should rotate in a clockwise direction, if not, exchange any two the motor connection wires to obtain the correct rotation.

6.1 Initial INFO Screen

Elevator Trim(Mode 1)

Elevator Trim(Mode 2)

Voltage

Time

Helicopter Flight Mode

Aileron Trim

Throttle Trim(Mode 2)

Throttle Trim(Mode 1)

Model Type

Current model number

Current Model

Rudder Trim

REAPER50 7.2V

DN 06:00

[ NORM ]

MDL 1

HELI

The INFO screen is displayed when the power is switched on. The screen has a two-page menu and rotating the ROLLER to the right moves forward

to the Function list screen, when you wish to return to the Initial INFO Screen from the Function list screen, rotating the ROLLER to the left returns

to the previous screen.

The function list screen allows you to display all of the information from the sensor attached to the receiver as well as the timer and key model information.

6.0 T-SIX Transmitter Settings

List

Enter

Down

ROLLER

FUNCTION LIST 1/2

MODEL SEL THRO CUR

PITC CUR

SWASH MIX

MIX 1

MIX 2

D/R&EXPO

TRAVEL ADJ

SUB TRIM

GYRO

The T-SIX utilizes a roller that can be rotated or pressed along with four buttons, LIST, ENTER, UP and DOWN that are used to access and program the functions.

(1) Voltage: When the transmitter voltage drops below 4.3 volts,

“Warning Low Battery” will flash along with an alarm sound. If you

are flying when this occurs, land immediately.

(2) Timer: Timer function allows you to program a Count Down timer or

Stop Watch (count up timer) to display on the main screen.

(3) Model Type: model type programs the selected model memory to

function in Helicopter or Airplane programming. You should

program the model type first when setting up a new model.

(4) Trim set up: The trim set up function allows servo movement

adjustment.

(5) Model display: you can see the selected model directly after your

model type has been selected.

6.2 Names and Functions of the Input Key

(1) LIST Key: when this key is pressed the screen changes to the Function Listing screen.

(2) ENTER Key: If this key is pressed when the INFO screen is being displayed, the screen will change to the My list screen. This can be used for moving

to each of the other functions.

(3) Up Key: if this key is pressed the select cursor will move up to your desired menu or list.

(4) DOWN Key: if this key is pressed the select cursor will move down to your desired menu or list.

(5) ROLLER: Press the ROLLER to access screens or functions. Or rotate the ROLLER to adjust values or to select options.

(6) Select Cursor: move the select cursor, then press the ROLLER and the screen will back to previous Menu.

6.3 MODEL SET

6.4 MODEL NAME

Initial INFO

Screen FUNCTION LIST

Press

ROLLER

Press

ROLLER

Press

ROLLER

Rotate

ROLLER

Rotate/press

ROLLER

Rotate

ROLLER

SETUP LIST

MODEL SEL

FUNCTION LIST MODEL NAME

MODEL SEL

6: MODEL 6

7: MODEL 7

8: MODEL 8

9: MODEL 9

10: MODEL 10

2: MODEL 2

3: MODEL 3

4: MODEL 4

5: MODEL 5

1: MODEL 1

MODEL NAME

MODEL 1 REAPER50

! ” # $ % & °[ ] * +,- . / 01234

56789 : ;< = > ? QABCDEFGHI

JKLMNOPQRSTUVWXYZ

Rotate ROLLER to choose “MODEL 1”, press ROLLER to confirm, then the screen will display

“DOWNLOAD...” and the transmitter will “beep” 3 times, this denotes that the choice is successful and it will return to the function menu automatically.