Hoist Fitness CL-3401 User manual

HD-3000
PERSONAL PULLEY
CL-3401
LEG EXTENSION
A01
A01A01
A01
**WARNING**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE EXERCISE
FLOOR USING MINIMUM 4 — ½” LONG BOLTS. FAILURE TO DO SO MAY
RESULT IN SERIOUS INJURY OR DEATH!

INSTRUCTIONS……………………………..…………………...
FRAME ASSEMBLY……………………..………..………….…
PRE-ASSEMBLY………………………………..……………….
DECAL PLACEMENT……………………….....………………..
DECAL REFERENCE………………...........….………….…….
PART LIST…………………………..……….…….…………..…
ABBREVIATIONS……………………..……….………….……..
BOLT SIZING CHART…………………………………………...
WASHER SIZING CHART…………….….…….……………....
MAINTANENCE SCHEDULE…………..………….………..….
GENERAL MAINTANENCE INFORMATION.............…….…
WEIGHT TRAINING TIPS…………………….……….………..
WEIGHT RATIOS………..…………………….……….………..
EXERCISE LOG…………………………………..……………...
LIMITED WARRANTY…………………………..……………….
02
04
1
23
24
25
2
30
31
33
34
35
36
37
38
PAGE 01 CL-3401 ASSEMBLY
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
CONTENTS

CL-3401 ASSEMBLY PAGE 02
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
SAE Hex Key Wrench Set
INSTRUCTIONS
Be ore beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description rom the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most e ective
exercise motion possible. A ter assembly, you should check all unctions to
ensure correct operation. I you experience problems, irst recheck the
assembly instructions to locate any possible errors made during assembly.
I you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted or, continue on.

PAGE 03 CL-3401 ASSEMBLY
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

CL-3401 ASSEMBLY PAGE 04
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY

OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
CABLE ROUTING DIAGRAM
PAGE 05 CL-3401 ASSEMBLY

CL-3401 ASSEMBLY PAGE 06
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
**STOP**
BEFORE CONTINUING ASSEMBLY,
REFER TO THE SSS CAGE 60 MANUAL
AND COMPLETE THE STEPS THERE

PAGE 07 CL-3401 ASSEMBLY
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.

CL-3401 ASSEMBLY PAGE 08
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

PAGE 09 CL-3401 ASSEMBLY
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

CL-3401 ASSEMBLY PAGE 10
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- INSTALL CABLES AND PULLEYS
AT THE SAME TIME
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

PAGE 11 CL-3401 ASSEMBLY
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
FINE TUNING
LOOSEN JAM NUT AND THREAD BOLT IN/OUT TO
GIVE THE CABLE PROPER TENSION.
RE-TIGHTEN JAM NUT.
CABLE BOLT
JAM NUT

CL-3401 ASSEMBLY PAGE 12
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.

PAGE 13 CL-3401 ASSEMBLY
OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.

OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CL-3401 ASSEMBLY PAGE 14

OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
PAGE 15 CL-3401 ASSEMBLY

OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CL-3401 ASSEMBLY PAGE 16

OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
PAGE 17 CL-3401 ASSEMBLY

OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE
- HAND TIGHTEN ALL PREVIOUSLY
HAND TIGHTENED HARDWARE
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
*IMPORTANT*
NOW THAT THE CL-3401 IS COMPLETELY ASSEMBLED, TAKE TIME TO ASSURE THAT
YOUR UNIT IS ASSEMBLED S UARE AND PERPENDICULAR. IF IT IS NOT
PERPENDICULAR IN BOTH DIRECTIONS, IT WILL BE NECESSARY TO LOOSEN SOME
FRAME HARDWARE TO RE-ALIGN THE FRAME AND RETIGHTEN BOLTS.
CL-3401 ASSEMBLY PAGE 18

OWNER’S MANUAL
OWNER’S MANUALOWNER’S MANUAL
OWNER’S MANUAL
PRE-ASSEMBLY
NOTE:
- INSTALL SEAT MOUNT (16) ONTO (17) BEFORE
ATTACHING STARRED COMPONENTS
*
*
*
*
*
**
PAGE 19 CL-3401 ASSEMBLY