Hoist Fitness CF-3367-A User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
Note: Both Serial Number and Model Number are Required when Ordering Parts
OWNER'S MANUAL
A03
CF-3367-A
CF-3367-A SQUAT RACK
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.

02
04
15
16
17
19
20
22
24
25
26
27
28
PAGE 01
OWNER'S MANUAL
EXERCISE LOG......................................................................
CF-3367-A ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
CONTENTS

Level
Adjustable Wrench
Two People
TOOLS REQUIRED
parts have been accounted for, continue on.
OWNER'S MANUAL
Tape Measure
Rubber Mallet
Be sure to have your serial number and this manual when calling. When all
1/2", 9/16" and 3/4" Sockets
PAGE 02CF-3367-A ASSEMBLY
Hex Key Wrench Set
Ratchet Wrench
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
INSTRUCTIONS

CF-3367-A ASSEMBLYPAGE 03
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 04
FRAME ASSEMBLY

FRAME ASSEMBLY
- HAND TIGHTEN HARDWARE.
NOTE:
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
PAGE 05
OWNER'S MANUAL
CF-3367-A ASSEMBLY
NOTE FOOTPAD ORIENTATION
28
32
7
2
28
22
44
1
20
28
28 32
FACING OUTWARD
(FAR SIDE)
NOTE FOOTPAD ORIENTATION
FACING OUTWARD
(FAR SIDE)

- HAND TIGHTEN HARDWARE.
NOTE:
FRAME ASSEMBLY
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 06
FACING OUTWARD
19
28
28
32
4
32 28
28
23
19
32
28
28
28
2
23
32 28
(FAR SIDE)
FACING FORWARD
NOTE FOOTPAD ORIENTATION
(FAR SIDE)
9
NOTE FOOTPAD ORIENTATION
NOTE SAFETY TIER ORIENTATION
ANGLED CUT THIS END
TUBE OFFSET TO THE OUTSIDE
1

16
43
42 9
25
28 32
28
32
4
1
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
HAND TIGHTENED HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
PAGE 07
OWNER'S MANUAL
CF-3367-A ASSEMBLY

- WRENCH TIGHTEN HARDWARE.
NOTE:
FRAME ASSEMBLY
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 08
10
40
13
41
24
27
14
30
1

20
32
22
28
28
2
FACING OUTWARD
NOTE FOOTPAD ORIENTATION
5
44
(NEAR SIDE)
28
28
3
32
NOTE FOOTPAD ORIENTATION
FACING OUTWARD
(NEAR SIDE)
FRAME ASSEMBLY
- HAND TIGHTEN HARDWARE.
NOTE:
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
PAGE 09
OWNER'S MANUAL
CF-3367-A ASSEMBLY

23
FACING FORWARD
FACING OUTWARD
2
(NEAR SIDE)
32
32
28
32
28
28
19
4
32
NOTE FOOTPAD ORIENTATION
28
28
5
28
23
28
28
8
19
NOTE FOOTPAD ORIENTATION
NOTE SAFETY TIER ORIENTATION
ANGLED CUT THIS END
TUBE OFFSET TO THE OUTSIDE
(NEAR SIDE)
- HAND TIGHTEN HARDWARE.
NOTE:
FRAME ASSEMBLY
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 10

FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
HAND TIGHTENED HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
PAGE 11
OWNER'S MANUAL
CF-3367-A ASSEMBLY
16
43
42
4
8
28 32
28
32
25
5

FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE STEP ON PAGE 14.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
OWNER'S MANUAL
CF-3367-A ASSEMBLY PAGE 12
24
41
13
10
14
30
27
40
5

FRAME ASSEMBLY
- HAND TIGHTEN HARDWARE.
NOTE:
IMPORTANT
BE SURE TO FULLY SUPPORT BOTH UPRIGHTS UNTIL
THEY ARE SECURELY FASTENED IN THE NEXT STEP.
IF THEY ARE NOT FULLY SUPPORTED, THEY WILL BE
UNSTABLE AND MAY FALL, POSSIBLY CAUSING
SERIOUS INJURY OR DEATH!
PAGE 13
OWNER'S MANUAL
CF-3367-A ASSEMBLY
1
18 12
18
18
30
29
18
5
15
26
30
29
30 26
12
18
15
18
29
30
26
26 29

FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY
HAND TIGHTENED HARDWARE.
OWNER'S MANUAL
CF-3367-A ASSEMBLY PAGE 14
*IMPORTANT*
NOW THAT THE CF-3367-A IS COMPLETELY ASSEMBLED TAKE TIME TO
ASSURE THAT YOUR UNIT IS ASSEMBLED SQUARE AND PERPENDICULAR. IF NOT,
IT WILL BE NECESSARY TO LOOSEN SOME FRAME HARDWARE TO RE-ALIGN THE FRAME
AND RETIGHTEN BOLTS.
17
28
5
6
21
32
28
FACING OUTWARD
(FAR SIDE)
NOTE FOOTPAD ORIENTATION
1
NOTE FOOTPAD ORIENTATION
FACING OUTWARD
(NEAR SIDE)

35
36
36
36
38
34
37
36
35
39
DECAL PLACEMENT
OWNER'S MANUAL
PAGE 15 CF-3367-A ASSEMBLY

021-0003803
021-0003113
021-0003221
021-0003008
021-0003804
SERIAL # DECAL
DECAL REFERENCE
CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 16

PART LIST
CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 17
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 026-01X5539 REAR UPRIGHT, LEFT 1
2 026-01X5470 BASE FRAME 2
3 026-01X5471 STAND-OFF-2 1
4 026-01X3690 FRONT UPRIGHT 2
5 026-01X5540 REAR UPRIGHT, RIGHT 1
6 026-01X5507 CROSSMEMBER 2
7 026-01X5508 STAND-OFF-1 1
8 026-01X5516 SAFETY TIER-2 1
9 026-01X5517 SAFETY TIER-1 1
10 026-01X5592 BAR RACK 2
12 026-01M0476 WEIGHT PEG 17.00" LG 6
13 026-01M2752 HEAVY FLANGED SPACER: .516" I.D. X 1.683" LG. 6
14 026-01M2276 END CAP DOMED 2
15 026-01M2278 WEIGHT PEG 12.3750" LG. 2
16 026-01P5131 BAR REST PLATE 2
17 026-01PL2503 RUBBER FOOT 8.41" X 9.13" 6
18 026-01PL2313 WEIGHT HORN RUBBER DONUT W/ 3.750 COPE 10
19 011-0107014 1/2"-13UNC X 5.00" HHB (WZ) 8
20 011-0207030 1/2"-13UNC X 4.50" HHB (WZ) 4
21 011-0107038 1/2"-13UNC X 4.25" HHB (WZ) 8
22 011-0407016 1/2"-13UNC X 3.00" HHB (WZ) 4
23 011-0107021 1/2"-13UNC X 5.50" HHB (WZ) 4
24 011-0101076 1/2"-13UNC X 3.25" BHCS (WZ) 6
25 011-0102038 1/2"-13UNC X 2.75" FHS (WZ) 4
26 011-0101003 3/8"-16UNC X 2.00" BHCS (WZ) 8
27 011-0101034 3/8"-16UNC X 1.25" BHCS (WZ) 2
28 013-0102003 1/2" X 27mm SAE FLAT WASHER (WZ) 64
29 013-0402007 3/8" X 22mm FLAT WASHER (WZ) 8
30 013-0102020 3/8" SPLIT LOCK WASHER (WZ) 10
32 012-0304011 1/2"-13 UNC THIN NYLOCK NUT (WZ) 36
34 021-0003008 DECAL COMMERCIAL MAINTENANCE 1.50 X 6.69 1
35 021-0003113 DECAL PINCH POINT 1.63" X 3.25" (VERTICAL) 2

ITEM NO. PART NUMBER DESCRIPTION QTY.
36 021-0003221 DECAL HOIST 2.50" X 9.13" 4
37 021-0003803 DECAL, WARNING, CF-3367 1
38 021-0003804 DECAL, DANGER, CF-3367 1
39 SERIAL # DECAL DECAL HOIST SERIAL # 1.63" X 2.63" 1
40 026-01M2761 BOSS THREADED 5/16 SOCKET HEAD .75" O.D. X 1.67" LG. 6
41 013-0903002 1/2" SPLIT LOCK WASHER (WZ) 6
42 026-01X3691 BAR HOOK-2 2
43 011-0102028 1/2"-13UNC X 3.75" FHS (WZ) 4
44 026-01PL2518 SCUFF GUARD 14.3" LG. (CONCAVE) WITH RIVETS/TAPE 2
PART LIST CONTINUED
CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 18
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED

SHCS = Socket Head Cap Screw
SHSS = Socket Head Shoulder Screw
BZ = Black Zinc
WZ = White Zinc
SS = Stainless Steel
HHB = Hex Head Bolt
FHCS = Flat Head Cap Screw
BHCS = Button Head Cap Screw
ABBREVIATIONS
CF-3367-A ASSEMBLY
OWNER'S MANUAL
PAGE 19