HoldPeak 700 User manual

Instruction Manual
Warnings!
It is important that users of this tester
read,understand,and follow all
warnings,cautions,safety information,and
instructions in this manual before operating or
servicing this tester.Failure to follow instructions
could result in death or serious injury.
Risk of electric shock and burn.Contact with live
circuits could result in death or serious injury.
Use caution with voltages above 30 V AC as a
shock hazard may exist.
A steady red glow and continuous beep
indicates voltage present.If no indication,voltage
could still be present.
In bright light conditions,the LED visual
indicators will be less visible.
Do not use if green LED is not illuminated.
Do not use if tester appears damaged or if the
tester is not operating properly.If in doubt,replace the
tester.
Do not apply more than the rated voltage as
marked on the tester(1000 volts AC).
Always wear approved eye protection.
Before each use,verify operation by testing a
known working circuit that is within the rating of this
tester.
Do not rely on this tester with shielded
wire.Operation may be affected by differences in
socket design and insulation thickness and type.
Comply with local and national safety
requirements.
If this tester is used in a manner not specified by
the manufacturer,protection provided by the tester
may be affected.
CAUTION
Do not attempt to repair this tester.It contains no
serviceable parts.
Do not expose the product to extremes in
temperature or high humidity.
Technical Data
Voltage range: 50...1000V AC
Frequency range: 50Hz...500Hz
Display: Clear, omnidirectional flashing beacon
IP-Protection: IP40
Overvoltage categorty : CAT III,600V
Pollution degree: 2
Altitude: up to 2000m
Temperature range: 0℃up to 40℃
Humidity: <80%
Power supply: 2x1,5V batt. IEC Lr03
Dimensions: 145x25x21 mm
Weight: Approx.42g
Display and Control Elements:
1) Test probe
2) LED for voltage indication
3) Battery case cover and Clip
4) Switch
SYMBOLS ON TESTER
Warning.Risk of electric shock.
Rish of danger.Important information.It is
important that users of this tester
read,understand,and follow all warning,safety
information,and instruction in this manual before
operating or servicing this tester.Failure to follow
instructions could result in death or serious injury.
Double insulated
OPERATING INSTRUCTIONS:
Turn unit on:
Press the power button on the end-cap for 1
second.Listen for a single-beep sound and watch for
a steady green LED to illuminate in the tip of the
①
②
③
④
HOLDPEAK 700

tester.Release the power button;the tester is now
activated and is operational.Tester on known live
circuit to verify tester functionality.
Turn unit off:
Press and hold the power button on the end-cap for
0.5 second. Listen for a double-beep sound and
watch the “power on” green LED turn off.Release the
power button :the tester is now deactivated and is
not operational.
System self-test:
The “power on” green LED visually confirms battery
sufficiency,system integrity,and operation active
mode.Always test on known live circuit to verify
tester functionality prior to use.
Checking for the presence of AC voltage:
Prior to use,test on known live circuit to verify tester
functionality.
Place tip of the tester near anAC voltage.If the tester
detects voltage,the “power on”LED in the tip of the
tester change color from green to blinking red and a
continual beeping sound is generated.
Low battery indication:
Scenario 1—Powering on the tester:The “power on”
LED in the tip of the tester change from a steady
green to a blinking green and a series of beeping
sounds is generated.The tester then turns off.The
unit is now deactivated and is not operational,the
batteries require replacement.To replaec the tester
batterieds refer to the Maintenance section
titled”Battery Replacement”.
Scenario 2—Operating the tester:If the LED lights
dim and the tone fades,the tester may require new
batteries.To replace the tester batteries refer to the
Maintenance section titled ”Battery Replacement”.
Auto Power Off:
After 4 minutes of non-use,the tester automatically
powers off to conserve battery life.Listen for a
double-beep sound and watch the “power on” green
LED turn off.The tester is now deactivated and is not
operational.
Maintenance
As long as the instructions in the operating manual
are adhered to, no special maintenance is required.
Cleaning:
Disconnect the instrument from all circuits.Humidity
the cloth slightly with household cleaner and wipe
the instrument surface by applying light
pressure. Allow a recovery time of 6 hours after
cleaning before operating the instrument.
Battery Replacement
Press the switch to power off, press the block and
push the battery case cover lightly to open.
Remove discharged battery and insert new ones by
respecting correct polarity. For battery type, pleasa
refer to the technical data section.
Carefully press battery case cover until latching.
Warning!
If the instrument is likely to remain unused for a long
period of time the batteries must be removed. If a
battery should leak inside the housing, return the
instrument to our service department for cleaning
and checking.
Please think of our environment when getting rid of
used batteries. They should be disposed of in a
place suitable for hazardous waste.
Warning!
Please, comply with the appropriate regulations
concerning the return, recycling and disposal of used
batteries and accumulators.
Above picture and content just for your
reference. Please be subject to the actual
products if anything different or updated. Please
pardon for not informing in advance.
PRESS
AND PUSH