Home Accents Holiday TG76M3ACDL20 User manual

Pre-Assembly
Assembling the tree stand
Assembly
Step 1. Choose a location near a wall outlet.
Step 2. Unfold the legs of the tree stand (D) and lay the stand on
the floor.
Step 3. Slide the locking disk of the tree stand (D) down until it
snaps into place.
This tree assmebles with Quick Set® technology ---Set up and
light up your tree in less than 10 minutes!
Step 1. Remove the protective caps from the tree bottom (C) and
insert the pole into the tree stand (D).
Step 2. Remove the protective caps from the tree center (B) and
insert the pole into the tree bottom (C) .
Step 3. Insert the tree top (A) into the tree center (B).
Step 4. Shape the branches to your preference by working from the
bottom to the top. When adjusting branches, ensure that all
wires are free of branch hinges.
Step 5. Inplug the adapter into the wall outlet. All your lights should
now be lit.
Step 6. Shape the tree from the bottom to the top. Start with the
branches farthest from the pole – fan out in a star shape,
and continue until the entire tree is shaped.
Step 7. When finished shaping the branches, slightly upsweep all
branch tips for a uniform look.
Assembling the tree
*Electrical Rating For The Tree
(For Indoor Use Only)
Input: 100-240V, 50/60Hz, 0.35A
Output: 29V DC 0.45A
Tree top
Adapter
To Be Plugged
Into Wall
Outlet
50S
100S
100S
100S
TM
Package Contents
A
B
C
D
Tree top
Tree center, sticker 2
Tree bottom, sticker 1
Tree stand
1
1
1
1
Quantity
Part Description
Top view Side view
Control box Foot Pedal
on/off Switch
Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
a. READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
When using electrical products, basic precautions should always
be followed, including the following:
b. Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI)
outlet. If one is not provided, contact a qualified electrician for proper
installation.
c. This seasonal product is not intended for permanent installation or use.
d. Do not mount or place the product near gas or electric heaters,
fireplaces, candles, or other similar sources of heat.
e. Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
f. Do not let lamps rest on the supply cord or on any wire.
g. Unplug the product when leaving the house, when retiring for the
night, or if left unattended.
h. This is an electric product and not a toy! To avoid risk of fire, burns,
personal injury and electric shock it should not be played with or
placed where small children can reach it.
i. Do not use this product for other than its intended use.
j. Do not hang ornaments or other objects from cord, wire, or light string.
k. Do not close doors or windows on the product or extensions cords as
this may damage the wire insulation.
l. Do not cover the product with cloth, paper, or any materi al that is not
a part of the product when in use.
m. The lamps of this product are not replaceable. Do not attempt to
change or modify the lamps.
n. Read and follow all instructions that are on the product or provide with
the product.
o. SAVE THESE INSTRUCTIONS
NEED HELP?
DO NOT RETURN TO STORE. Call: 1-877-527-0313
Form 8am to 5pm EST, Monday through Friday.
Section 2
Section 1
Align both arrows
in a straight line
before sliding
down to insert
Open the
cap cover
Do Not Tamper
Internal Parts
Christmas Tree
Model: TG76M3ACDL20
Sku # 1001 540 401
50S
100S
100S

Christmas Tree
Model: TG76M3ACDL20
Sku # 1001 540 401
TM
NOTE: If some bulbs do not light or flicker, search for any loose
plugs and/or provided in order to maintain the performance and
life expectancy of your tree.
Step 1. Connect the light strings of the tree together and plug the
adapter into a wall outlet.
Step 2. If the tree comes with a foot pedal, step on the On/Off
button.
Operation
Turning on the tree
This tree package includes hinge pins, washers for any replacement
or repair that you need to perform on your tree. If extra parts are
needed, contact the Customer Service Team at 1-877-527-0313
between the hours of 8 am and 5 pm EST, Monday through Friday.
Repairing Loose Hinges
Step 1. Place the branch into the slot of the bracket.
Step 2. Insert a new hinge pin through the holes of the bracket
and secure with a washer.
Maintenance
Spare parts
CAUTION:Use only power adapter that was provided
with this product. Using a different power adapter will damage
the lights and cause fire, electrical shock hazard.
Troubleshooting
Problem Solution
The tree does
not light
Ensure that all tree sections are plugged
into each other and that the tree is
plugged into the wall. If your tree came
with a foot pedal, step on the On/Off
button.
HOW TO USE THE DUAL COLOR LIGHT CONTROLLER:
Press the selector button on the “Light Controller”
to select among:
(1) SLOW FADING
(2) TWINKLE
(3) FAST FADING
(4) COMBINATION
(5) STEADY ON
User servicing instructions
Light
Controller
Selector
Button
1. Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged or frayed wire insulation or
cords, cracks in the lampholders or enclosures, loose
connections, or exposed copper wire.
2. Before disassembling the tree, unplug the tree and remove all
ornaments and decorations.
3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
4. Repeat this step for the center and bottom tree sections.
5. When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to
avoid anyundue strain or stress on the product conductors,
connections, and wires. Cover the
protective cap on the poles to avoid
damaging the internal parts.
6. When not in use, store neatly in a cool,
dry location protected from sunlight.
Use and Care Instructions
To activate the DEMO mode:
1. With the tree plugged in, press and hold the FUNCTION button of
the in-line controller/receiver for 5 seconds.
2. The Clear Lights will blink 3 times. The tree is now in DEMO mode.
3. Within DEMO mode, the tree will display the COMBO pattern at all
time unless the function button is pressed to change the flashing
pattern. The tree will return to COMBO pattern whenever the
controller is idle for 30 seconds.
To deactivate the DEMO mode:
1. With the tree plugged in and in DEMO mode, press and hold the
FUNCTION button of the in-line controller/receiver for 5 seconds.
2. The multi-light will flash 5 time indicating that DEMO mode is off
(Clear lights will flash 5 times with single color LED trees).
3. The tree is now in normal mode. Flashing pattern can be set to
whichever desired and the tree will remember the last setting.
*IN-LINE CONTROLLER/RECEIVER
*Controller
Tree Comes with Demo Mode Not Activated