Home Decorators Collection FSA10041A-ST User manual

page 1-10
ST. AUGUSTINE LOVESEAT CHAIR
Please read over this instruction manual as it will save time in the
assembly of this product.
Note: Prior to assembly, please open and lay parts out on a clean, soft
flat surface to avoid any damages to the product’s finish.
HDC#:TBD MFG#:FSA10041A-ST

page 2-10
Caution:
The St. Augustine loveseat chair was made for the explicit purpose of
providing outdoor functions and is not to be used as a toy. This product
is not intended for inclement /severe weather in any form including, but
not limited to: rain, hail, sleet, snow and/or wind. Manufacturer
recommends that with formidable weather approaching you store and/or
cover this chair. Do not locate structure near any open flame. Do not use
structure as a support. Do not shake, lean or climb on structure. Children
under age of 10, near the structure, should be supervised by a competent
adult at all times. This product is NOT intended for commercial use and
will void the warranty.
WARRANTY
Yotrio Corporation, City of Industry, CA. 91748, extends five years frame
and two years fabric limited warranty to the original purchaser as a sign
of our dedication to the highest possible quality standards. The warranty
is designed to cover the loveseat chair under normal residential use.
This Warranty is non-transferable and void if the furniture is used in
non-residential environment and/or has been abused. The warranty also
becomes void in the event the chair has been damaged by acts of God,
calamity or misuse. This warranty does not cover in the event of
inclement weather such as rain, hail, sleet, snow or wind. We reserve the
right to make substitutions with similar merchandise, if the model in
questions is no longer in production. The manufacturer recommends
that with ANY formidable weather approaching you disassemble and
store your chair in a safe location.
CARE AND MAINTENANCE:
For best results, clean the frame with damp cloth and dry thoroughly.
This will help prevent mildew by removing dirt particles that may
accumulate. Do not use abrasive materials or cleaners. Cushions may be
cleaned by hand with mild soap and water. Rinse cushions thoroughly
and allow drip-drying. Do not machine wash or tumble dry as cushions
may shrink. Do not use bleach or solvents on fabric. In order to prolong
the life of your chair, when not in use or in inclement weather (rain, hail,
sleet, snow, wind), fire, extreme heat and freezing conditions, the chair
needs to be stored in a dry, sheltered place.

page 3-10
DO NOT RETURN TO RETAILER
IF YOU HAVE ANY QUESTIONS OR CONCERNS
PLEASE VISIT OUR WEBSITE AT:
www.homedecorators.com
OR TOLL FREE AT:
1-800-245-2217
MONDAY-FRIDAY 8:30 AM TO 5:00 PM PACIFIC STANDARD TIME / 11:30
AM TO 8:00PM EASTERN STANDARD TIME
Warranty Coverage Requirements:
1. Copy of your Original Store Receipt.
2. Pictures of the damaged parts.
3.You must know the name of your product and any corresponding item
numbers as well as the name of the store where you purchased the
item.
4.Please gather all of this information BEFORE you call customer
service.

page 4-10
Parts Check List
Please remove all parts carefully from box and lay out on clean, soft
surface to protect product’s finish.
①
Backrest –1PC
②
Right Arm –1PC
③
Left Arm –1PC
④
Seat – 1PC
⑤
⑥
Leg connector –1PC Cushion –4PCS

page 5-10
A. M6X18 Bolt – 12PCS +1 B. M6X25 Bolt – 2PCS+1
C. M6X40 Bolt – 2PCS +1 D. M6 Washer – 16PCS+1
E. Hex wrench – 1PC

page 6-10
1.Lay down the left arm(3) on a soft surface, Attach the seat (4) to
the left arm(3) using M6X18 bolts (A) and M6 washers(D), Use the
hex wrench(E) to loosely tighten all the bolts.
Do not fully tighten all the bolts!

page 7-10
2. Attach the seat (4) to the right arm (2) using M6X18 bolts (A)
and M6 washers(D), Use the hex wrench(E) to loosely tighten all
the bolts.
Do not fully tighten all the bolts!

page 8-10
3.Attach the leg connector (5) to the left arm(3) and the right
arm(2) using M6x18 bolts and M6 washers(D), Use the hex
wrench(E) to loosely tighten all the bolts.
Do not fully tighten all the bolts!

page 9-10
4. Attach the chair backrest (1) to the left arm(3) and right
arm(2) using M6x40 bolts(C), M6X25 Bolts (B), and M6
washers (D) ,Use the hex wrench(E) to loosely tighten all
the bolts.
Do not fully tighten all the bolts!

page 10-10
5. Once all the bolts are in place. Fully tighten all the bolts
with the hex wrench (E). Check to ensure the chair is tightly
assembled and stable before use.
Place the cushions (6) on the chair and enjoy.