Home Decorators Collection OXFORD BF-22419 User manual

BF-22419 OXFORD COLLECTION TWO DRAWER END TABLE
Home Decorators
Collection
ASSEMBLY INSTRUCTIONS
Made In China

RIGHT
BOTTOM PANEL-1PC
PARTS LIST
code letter of part(s)need
numbered to assure fast,easy and correct assembly.
IMPORTANT NOTE:
Thank you purchasing this quality produst.Be sure to check all packing
Follow instructions listed below in proper sequence as
carton during shipment. Count all parts and material hardware,Compare
with parts list to be sure all part are present.If any parts are missing
or damaged,phone,fax,or mail to our Customer Service Department.For
efficient and speedy service please indicate the model number and
material carefully for small parts,which may have came loose inside the
JKL
IHG
DEF
C
B
A
TOP PANEL-1PC
LOW PANEL-1PC
ACROSS PANEL-3PCS
FRONT DRAWER PANEL-3PCS
RIGHT SIDE PANEL-1PC
SIDE DRAWER PANEL-3PCS
LEFT SIDE PANEL-1PC
BASE DRAWER PANEL-3PCS
BACK PANEL-2PCS
BACK DRAWER PANEL-3PCS

REAR PANEL GUIDE-1PC
V
U
SCREWS-3PCS
P
ST
QR
ONM
SCREWS-26PCS
SCREWS-14PCS
DOWELS-8PCS
CAM-BOLTS-12PCS
KNOB-3PCS
SCREWS-1PC
CAM-TOOL-1PC

THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS
NOTE:
TO PREVENT DAMAGE DURING ASSEMBLY,PLEASE ASSEMBLE THIS ITEM WITH AT
HOW TO USE THE CAM-TOOL
M
ARROW
N
ARROW
SHOULDER
LEAST TWO PEOPLE.
TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
NOTE:
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT.IN ORDER
UPON OPENING THOROUGHLY CLEAN ALL WOODS SURFACES TO REMOVE DUST
NOTE:

INSERT THE BASE PANEL(J)INTO SLOT IN SIDE DRAWER PANEL.
ATTACH DRAWER SIDE PANEL(K/L)TO FRONT DRAWER PANEL(H)USING SCREWS(T).
ATTACH KNOB(S)TO FRONT DRAWER PANEL(H) USING SCREWS(T).
ATTACH DRAWER BACK PANEL(I)TO SIDE PANEL(K/L)USING SCREWS(T).
ASSEMBLE DRAWER
2
)
1
1
3

C
G
P
F
F
R
MD
2). ASSEMBLE SIDE PANEL(B/C).
INSERT THE 8 DOWELS(P)INTO HOLES IN ACROSS PANEL(F)AND LOW PANEL(G).
ROTATE THE CAM-BOLTS(N)INTO HOLES IN SIDE PANEL(B/C).
ATTACH THE LOW PANEL(G)TO BOTTOM PANEL(D)USING SCREWS(R).
PLACE CAM-BOLTS(N)INTO HOLES IN PANEL(F/D)AND ATTACH USING CAM-LOCKS(M).

3). ASSEMBLE THE TOP PANEL(A).
ROTATE THE 4 CAM-BOLTS(N)INTO HOLES IN TOP PANEL(A).
PLACE CAM-BOLTS(N)INTO HOLES IN SIDE PANEL(B/C)AND ATTACH USING 4 CAM-LOCKS(M).

4).
PUSH THE 3 DRAWER IN TO SLIDE-OUTS.
ASSEMBLE THE DRAWERS.

E
V
E
T
O
5). ASSEMBLE THE BACK PANEL(E).
INSERT THE BACK PANEL(E)INTO SLOTS IN REAR PANEL GUIDE(V).
ATTACH THE BACK PANEL(E)AND REAR PANEL GUIDE(V)USING SCREWS(O/T).