Home Zone Security ES06529V User manual

Twin-Head Dusk to Dawn Security Light
Model No. ES06529V
[phone]
IMPORTANT SAFETY OPERATING INSTRUCTIONS
1. Please read all warning and instruction before attempting to install this light.
2. Disconnect power before installing or servicing.
1. Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
2. Make sure all electrical and grounded connections are in accordance with the National Electrical Code and
applicable local code requirements.
3. All wiring connections should be in compliance with UL standard.
securit y
www.homezonesecurity.com
RISK OF ELECTRICAL SHOCK
1. Wear gloves and safety glasses at all times when moving luminaire from carton, installing, servicing or
performing maintenance.
2. Avoid direct eye exposure to the light source while it is on. Or this may cause irreparable damage to the
eyes.
3. Account for small parts and destroy packing material, as these may be hazardous to children.
RISK OF INJURY
1. Allow fixture to cool before touch.
2. Do not exceed maximum wattage marked on luminaire label.
RISK OF BURN
Attention: lights must to be installed by the experienced household wire installer or a qualified electrician,
Electrical system and the electrical connection method of light fixture must conform to the national electrical
standards and specification requirements of the local architecture.
1. Illumination output: approx. 2000 lumens / 5000K
2. Wattage: 20 W
3. Power source: AC120V/60Hz
REF. PARTS
PARAMETER:
A B C D E F G H I
A 1PC D Rubber cover 1PC G Tie bolt 1PC
B 1PC E Rubber ring 1PC H
Mounting screw
2groups
(4PCS)
C 1PC F Wire nut
3PCS
Light fixture
Mounting bar
EVA gasket I Ground screw 1PCC

1.Fix the Mounting bar (Part B) installation hole with junction box holes
by Mounting screws (Part H, choose one group of suitable Mounting
screws) as Figure 1, the screws are included in hardware pack.
Note: For the best performance, install fixture at 8 feet ~12 feet
(2.4~3.6m) above the ground.
3. Install the light on the Eva gasket (Part C) and bracket by Tie bolt
(Part G) and Rubber ring (Part E).
4. Cover the tie bolt using the screw cap (Part D). Use waterproof
glue to seal the rear cover and the light to make sure the lamp
waterproof.
2. Connect the source wires from the light and junction box through
the Eva gasket (Part C) as Figure 2
Conect the white wire to white by Wire nuts (F)
Conect the black wire to black by Wire nuts (F)
Connect the yellow/green wire of light to yellow/green wire from
junction box using ground screw (green) onto the bracket
Note:
DO NOT connect electricity before installation and maintenance
DO NOT cut or remove any connectors on the wire to make sure the
positive and negative connection is correct.
[phone]
HOW TO INSTALL
Twin-Head Dusk to Dawn Security Light
Model No. ES06529V
securit y
www.homezonesecurity.com
Figure 1
Figure 4
Figure 2
Black
White
LN
Waterproof glue
Rubber Screw Cap
Figure 3 Black
White
LN
Tie Bolt Rubber Ring

[phone]
Adjusting the lamp heads
Swing the lamp heads horizontal or vertical to adjust the light
coverage area and tighten the locking nut behind the light head.
Note: Keep the light head 30 degrees below horizontal to avoid water
damage and electrical shock.
Note: The light fixture is with photocell, it will light on at dusk
automatically.
HOW IT WORKS
1. Clean periodically with soft cloth.
2. Do not use any cleaners with chemicals, solvents or harsh abrasives on this light. Do not use scouring pads, powders, steel
wool or brasive paper. They could cause deterioration of the finish.
CLEANING AND MAINTENANCE
Twin-Head Dusk to Dawn Security Light
Model No. ES06529V
securit y
www.homezonesecurity.com