Homebase 647422 User manual

INSTRUCTION MANUAL
IMPORTANT: Please read these instructions before
using the product and retain for future use.
HHGL Limited, MK9 1BA
HHGL (ROI) Limited, D02 X576
18"
PEDESTAL FAN

2
SAFETY WARNINGS
Read this information carefully before installation or use of
this product. Keep this manual with the product for future
reference.
1. This appliance can be used by children aged from 8
years and above, and persons with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, if they have been given supervision or
instruction concerning the use of the appliance in a safe
way and if they understand the hazards involved.
2. Children should not play with the appliance.
3. Cleaning and maintenance should not be undertaken by
children without supervision.
4. Children should be supervised to ensure that they do not
play with the appliance.
5. appliance is not in use.
6. Do not operate any appliance with a damaged power cord
or plug; if the appliance malfunctions; or if it is dropped
or damaged in any manner.
7. Do not use outdoors.
8. Do not use any appliance for anything other than its
intended use. This product is intended for household use
only.
9. This appliance is intended to be plugged in a standard
domestic power socket only.
10. Do not misuse the power cord. Never carry the appliance
by the power cord or pull to disconnect it from the
socket. Instead, grasp the plug and pull to disconnect.
11. Do not attempt to repair, disassemble or modify the
appliance yourself. There are no user-serviceable parts.
12. not be tripped over.
13. Do not insert or allow foreign objects to enter the grille
openings, as this may cause damage to the appliance
and/or injury to the user.

3
15.
16. Never use the fan without the guard. Do not use the fan
if the fan blade is damaged or cracked.
17. Do not leave hair, tissue, tablecloths, clothes or curtains
near any opening on the fan, they could be sucked into
the fan and taken within the internal moving parts,
which could cause injury or damage.
18. Do not use the fan in wet or damp locations such as
bathrooms.
19. Keep the fan away from pets.
20.Check the voltage indicated on the rating plate. This
product is designed for a 220-240V~ 50-60Hz electric
supply. Periodically check the power cord of this fan.
21. If the power cord is damaged, it must be replaced by
persons in order to avoid a hazard.
22.
23. Do not use this fan near a window or in direct sunlight.
24. Do not try to disassemble this fan; there are no
parts which can be repaired by the user. If you need
maintenance, please contact your local store.
14. supply before removing the guard.

4
TECHINCAL INFORMATION
Information to identify the model(s) to which the information relates to
Description
Model identifier(s): 647422
Maximum fan flow
rate
Symbol Value Unit
F m3/min
Fan power input P W
Service value SV (m3/min)/W
Standby power
consumption PSB W
Fan sound power
level LWA dB(A)
Maximum air
velocity C
--
metres/sec
Measurement
standard
for service value
TECHNICAL SPECIFICATION
MODEL FS40-89
ARTICLE NO. 647422
WATTAGE 75W
WEIGHT 6.4kg
VOLTAGE 220-240V~
FREQUENCY 50-60Hz

5
ICON EXPLANATION
This appliance conforms to relevant directives of
The European Community.
The product complies with the applicable UK directives.
Class II appliance.
This marking indicates that this product should not be disposed
with other household waste. To prevent possible harm to
the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable
reuse of material resources. To return your used appliance,
please use the return and collection systems or contact the
store where the appliance was purchased. They can take this
product for environmentally safe recycling.

6
PRODUCT STRUCTURE
ASSEMBLY
Loosen and remove the L style screw (19) and lock
plate (18) from the outer pipe (17).
Connect the base cover (20) and gravity block (21)
together, to create the base. Then lay them on a dry,
flat foor.
Insert the outer pipe (17) into the hole of the base and
lock the L style screw (19).
Loosen the height adjustment control collar (16) on
top of the inner pipe (15). Pull the inner pipe (15) out
from the outer pipe (17) to adjust the fan to the
1.
2.
4.
3.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
Front Grille
Safety screw
Nut
Blade Cap
Blade
Plastic Grille Nut
Rear Grille
Motor shaft
Motor
Front plastic housing
Back Plastic Housing
Control Panel
Set screw
Power cord
Inner pipe
Height Adjustment
Control Collar
Outer Pipe
Plate
L Style Screw
Base Cover
Gravity Block

7
PLACING THE MOTOR ON TO THE
INNER PIPE
Loosen the height adjustment control collar (16).
Carefully pull the inner pipe out to the desired height,
then re-tighten the height adjustment control collar (16).
Loosen the set screw (13).
Place the head of the motor (09) on to the inner pipe.
Firmly tighten the set screw (13).
1.
2.
3.
4.
NOTE: Never fully remove the height adjustment control
collar (16), as this may result in the inner pipe detaching and
damaging the
appliance.
desired height and tighten the height adjustment
control collar (16).
Remove the plastic grille nut (06) by rotating it
anti-clockwise from the motor shaft (08).
Place the rear grille (07) into position. If this is done
correctly, the hole which is use for safety screw of the
grille should be at the bottom.
Fix the rear grille (07) into position by locking the
plastic grille nut (06) tightly.
The groove in the centre of the fan blade (05) aligns
with the bolt on the motor shaft (08) to ensure
it’s installed correctly.
Fix the blade (05) into the motor shaft (08) gently by
hand, then tighten the blade cap (04) by rotating it
anti-clockwise.
Mount the front grille (01) onto the rear grille (07) by
hanging the top hook clip of front grille over the top of
the rear grille. Close the clasps all around the grille,
then fit the nut and screw through the hole in the
bottom edge of the front grille, and tighten.
Test the blade to check whether it can can rotate
freely. If not, please rework step 6 onwards.
5.
6.
7.
8.
9.
10.
11.

8
Wind mode: Natural, sleep
Wind speed: Low, middle, high
1-7H timing: 1-7 hours
Press the ON/SPEED button to start the fan. Press this
button repeatedly to select the desired fan speed: Low,
medium or high.
Timing function: Press TIMER button to start the timing
function. The timer can be set up to 7 hours. To increase the
time by 1 hour intervals, continue to press the 'TIMER' button
up to 7 times, to reach the desired time.
Oscillation function: Press the SWING button to start the
Oscillation function, press it again to turn off the Oscillation
function.
OFF: Press the OFF button to stop the fan.
Wind speed: Press this SPEED
button repeatedly to select
the desired fan speed: Low,
medium or high.
Press the POWER button to
start the fan.
Oscillation function: Press the
OSC button to turn on the
Oscillation function, press it
again to turn off this function.
Wind: Press the MODE button
to select or switch between
natural and sleep modes.
Timing function: Press TIMER
button to start the timing
function. The timer can be set
up to 7 hours. To increase the
time by 1 hour intervals,
continue to press the 'TIMER'
button up to 7 times, to reach
the desired time.
OPERATION VIA APPLIANCE
OPERATION VIA REMOTE
OPERATION
Tilt Control
The airflow can be adjusted upward or downward by tilting
the fan head as desired.

9
CLEANING
Always unplug the fan before cleaning.
Use a soft damp cloth with a mild soap to clean the fan.
DO NOT use abrasive cleaners.
DO NOT immerse the fan in water and never allow water to
drop into the motor component.
DO NOT use petrol, thinner or other chemicals to clean
the fan.
1.
2.
3.
4.
STORAGE
–
Store the appliance and any accessories in a dry,
well-ventilated place.
–
In case of longer periods without operation, protect the
device and its accessories against soiling and corrosion.

PLUG REPLACEMENT
WARNING! The wires in the mains lead are coloured in
accordance with the following code:
Blue – Neutral
Brown – Live
As the colour of the wire in the mains lead of this appliance
may not correspond with the coloured marking identifying
the terminals in your plug, proceed as follows:
The blue wire must be connected to the terminal marked N
or coloured black.
The brown wire must be connected to the terminal marked
L or coloured red.
WARNING! Never connect live or neutral wires to the
Connect Blue
to N (Neutral)
Outer sleeve
firmly clamped Cable grip
Brown L (Live)
Fuse
approved to
BS 1362
If you need to replace the fitted plug, then follow the
instructions below.
earth terminal of the plug. Only fit an approved BS 1363 or
BS 1363/A plug and correctly rated BS 1362 3 Amp fuse. If
in doubt, consult a qualified electrician.
NOTE: If a moulded plug is fitted and has to be removed,
take great care in disposing of the plug and severed cable;
it must be destroyed to prevent it being accidentally
plugged into a power socket.
10