Homech HM-BD002 User manual
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
IMPORTANT: PLEASE STORE THESE
INSTRUCTIONS FOR FUTURE
REFERENCE!
READ THE INSTRUCTIONS CAREFULLY
BEFORE USING THE PRODUCT,
ESPECIALLY THE SAFETY INSTRUCTIONS.
SHOULD YOU GIVE THIS UNIT TO
ANOTHER PERSON, IT IS VITAL THAT YOU
ALSO PASS ALONG THESE INSTRUCTIONS.
ICONS
THIS GUIDE CONTAINS IMPORTANT
INFORMATION ABOUT USING,
OPERATING, AND STORING THE
PRODUCT. PLEASE READ IT THROUGH
AND NOTE THAT NON-OBSERVANCE
OF THESE INSTRUCTIONS CAN RESULT
IN SERIOUS INJURY OR DAMAGE TO
THE DEVICE.
WARNING
THESE WARNING NOTES MUST BE
OBSERVED TO PREVENT ANY INJURY
TO THE USER.
CAUTION
THESE NOTES MUST BE OBSERVED TO
PREVENT ANY DAMAGE TO THE DEVICE.
NOTE
THESE NOTES GIVE YOU USEFUL
ADDITIONAL INFORMATION ON THE
INSTALLATION OR OPERATION.
LOT LOT NUMBER
MANUFACTURER
DO NOT PUNCTURE THE BLANKET.
DO NOT USE THE BLANKET WHEN
IT IS FOLDED.
ONLY USE THE BLANKET INDOORS.
40 THE BLANKET CAN BE WASHED IN
GENTLE CYCLE AND BY HANDS AT
MAX 40°C/104°F.
DO NOT BLEACH!
DO NOT DRY THE BLANKET IN A
TUMBLE DRIER.
DO NOT IRON THE BLANKET.
DO NOT DRY CLEAN!
· THE APPLIANCE IS ONLY TO BE
OPERATED THROUGH ITS CONTROL.
· PLEASE CHECK THE BLANKET
BEFORE EACH USE. DO NOT USE IF
YOU NOTICE WEAR, DAMAGE, OR
SIGNS OF IMPROPER USE ON THE
CONTROL, CABLE, OR BLANKET.
RETURN THE DAMAGED PRODUCT TO
THE SUPPLIER.
· BEFORE CONNECTING THE PRODUCT
TO A POWER SUPPLY, PLEASE MAKE
SURE THAT THE SUPPLY VOLTAGE
STATED ON THE RATING PLATE IS
WITHIN THE ALLOWED POWER RANGE.
· DO NOT FOLD OR CREASE THE
BLANKET DURING USE.
· DO NOT PIERCE THE BLANKET WITH OR
ATTACH SAFETY PINS OR OTHER SPIKY
OR SHARP OBJECTS TO THE BLANKET.
· DO NOT USE THE BLANKET ON
CHILDREN OR PERSONS WHO ARE
DISABLED, ASLEEP, OR INSENSITIVE
TO HEAT.
· THE UNIT IS DESIGNED FOR HOME
USE ONLY.
· DO NOT KEEP THE BLANKET SWITCHED
ON AFTER YOU FALL ASLEEP.
· PROLONGED USE OF THE BLANKET
AT A HIGH SETTING COULD LEAD TO
SKIN BURNS.
· DO NOT COVER THE BLANKET
WITH ANY OTHER CUSHIONS. THE
CONTROL SHOULD NOT BE COVERED
OR PLACED ON OR BELOW THE
BLANKET WHILE IT IS IN OPERATION.
· DO NOT SIT ON THE BLANKET,
ONLY PLACE THE BLANKET ON THE
PART OF YOUR BODY YOU WANT
TO TREAT.
· NEVER TOUCH A BLANKET THAT
HAS FALLEN INTO WATER. UNPLUG
THE UNIT FROM POWER IMMEDIATELY.
· KEEP THE POWER CORD AWAY FROM
HOT SURFACES.
· NEVER CARRY, PULL, OR TURN THE
BLANKET BY THE CORD AND DO
NOT LET THE CORD GET TANGLED.
· DO NOT USE THE BLANKET WHEN IT IS
WET AND ONLY USE IT IN DRY
ENVIRONMENTS (NOT IN THE
BATHROOM OR SIMILAR ENVIRONMENTS).
· DO NOT EXPOSE THE CONTROL AND
CABLE TO MOISTURE OR HUMID.
· IF A FAULT OCCURS, DO NOT ATTEMPT
TO REPAIR THE UNIT BY YOURSELF .
REPAIRS MUST ONLY BE CARRIED OUT
SAFETY INFORMATION BY AN AUTHORIZED TECHNICIAN OR
OTHER SUITABLY QUALIFIED PERSONNEL.
· IF THE CABLE IS DAMAGED, IT MUST BE
REPLACED BY ITS MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY
QUALIFIED PERSONS IN ORDER TO
AVOID A HAZARD. WHEN STORING THE
BLANKET, ALLOW IT COOL DOWN
BEFORE FOLDING.
WARNING
· CONSULT YOUR DOCTOR BEFORE
USING THE BLANKET IN CASE YOU
HAVE ANY HEALTH CONCERNS.
· DO NOT USE THE BLANKET ON PARTS
OF THE BODY THAT ARE SWOLLEN,
INJURED, OR INFLAMED.
· IF YOU EXPERIENCE PERSISTENT PAINS,
IT CAN BE SYMPTOMS OF SERIOUS
ILLNESS, STOP USING IMMEDIATELY
AND CONSULT YOUR DOCTOR.
· IF YOU EXPERIENCE ANY PAIN OR
DISCOMFORT WHILE USING THE UNIT,
STOP USING IT IMMEDIATELY. NOT
INTENDED FOR MEDICAL USE
IN HOSPITAL.
INSTRUCTIONS BEFORE USING
PLEASE CHECK IF THE UNIT AND ITS
PARTS ARE INTACT AND NOT DAMAGED
IN ANY WAY. IF THERE IS ANY ISSUE,
PLEASE CONTACT THE SELLER.
WARNING
PLEASE ENSURE THAT POLY BAG
IS KEPT AWAY FROM CHILDREN!
RISK OF SUFFOCATION!
· DO NOT USE THE BLANKET WHEN IT
IS WET.
· DO NOT USE ON A HELPLESS PERSON,
AN INFANT, OR A PERSON INSENSITIVE
TO HEAT.
· CHILDREN NOT TO USE THIS
APPLIANCE DUE
TO THEIR INABILITY
TO REACT TO OVERHEATING.
· WHEN STORING THE APPLIANCE,
ALLOW IT TO COOL DOWN BEFORE
FOLDING. DO NOT CREASE THE
BLANKET BY PLACING ITEMS ON TOP
OF IT DURING STORAGE.
· USE ONLY THE CONTROL MARKED ON
THE RATING LABEL.
1 2 3 4 5 6
Model: HM-BD002
Homech Heated Throw Blanket
USER
GUIDE
NORTH AMERICA
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II,
Shenzhen, China
MADE IN CHINA HMBD002_V1.0_EN
www.homech.net
Intertek
5005416
CM
IMPORTANT
SAFETY
INSTRUCTIONS
DO NOT DESTROY
DANGER - To reduce the risk of burns,
electric shock and fire, this product must
be used in accordance with the following
instructions.
1. READ ALL INSTRUCTIONS.
2. DO NOT USE WHILE SLEEPING.
3. DO NOT USE ON AN INFANT.
4. THIS BLANKET IS NOT TO BE USED ON OR
BY AN INVALID, SLEEPING OR UNCONSCIOUS
PERSON, OR A PERSON WITH POOR BLOOD
CIRCULATION UNLESS CAREFULLY ATTENDED.
5. DO NOT USE ON AREAS OF INSENSITIVE
SKIN.
6. BURNS CAN OCCUR REGARDLESS OF
CONTROL SETTING, CHECK SKIN UNDER
BLANKET FREQUENTLY.
7. DO NOT USE PINS OR OTHER METALLIC
MEANS TO FASTEN THIS BLANKET
IN PLACE.
8. DO NOT SIT ON OR CRUSH BLANKET -
AVOID SHARP FOLDS.
9. NEVER PULL THIS BLANKET BY THE
SUPPLY CORD.
10.DO NOT USE THE CORD AS A HANDLE.
11.LOOP CORD LOOSELY WHEN STORING,
TIGHT WRAPPING MAY DAMAGE CORD
AND INTERNAL PARTS.
12.SAVE THESE INSTRUCTIONS.
Thanks for choosing Homech Heated Throw Blanket. Please
read this User Guide thoroughly before use and retain it for
future reference.
Package Contents
1 x Homech Heated Throw Blanket (HM-BD002)
1 x User Guide
Cleaning and Maintenance
·Be sure to disconnect the appliance from the mains by
removing the plug from the power outlet and cooling it
down for at least ten minutes before cleaning.
·Use only a soft brush to clean the blanket when dry.
·DO NOT use strong detergents or hard brushes to clean the
blanket.
·Gentle Machine Wash: Select Gentle Cycle for Wool, detach
the control connector, place the blanket in the laundry bag,
then wash at maximum of 40°C/104°F.
·Untangle the cable from time to time.
Troubleshooting
Specifications
Use the Heated Throw Blanket
1. Connect the power adapter to a power outlet. The whole
LCD display screen will light up in 1 second, indicating the
screen is working. Then the screen backlight will turn off and
the blanket enters standby mode.
2. Press the ON/OFF (Power) Button to turn on the blanket with
default temperature of “H” and timer of 3hrs.
3. Set Temperature Level: Press the Mode Button. When “H”
Product Diagram
①Mode Button
②Temperature Button
③Power Button
④Digital Display Screen
⑤Timer Button
Model
Input
Power
Dimensions
Operation Conditions
Storage Conditions
HM-BD002
120V~ 60Hz
120W
50 x 60 in
Indoor use only
Laid out clean and dry
A
B
A. Control Connector
B. Blanket Connector
Note:
·The connector of the controller and the blanket must
be interconnected before plugging the appliance to a
power source.
·IMPORTANT - This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. DO NOT attempt to rig this
safety feature.
Warranty and Service
This product is covered with Homech product and labor
warranty for 12 months from the date of its original purchase.
If any problems occur, please contact the Homech Customer
Care Centre via the contact information listed in this
User Guide.
We can only provide after sales service for products that are
sold by Homech or Homech authorized retailers and
distributors. If you have purchased your unit from a different
place, please contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
①②③
O
N
/
O
F
F
e
d
o
M
T
e
m
p
T
i
m
e
r
5
④
starts to flash on the top left of the screen, press the Temp
Button to select temperature from 1~9 & H levels (highest
level: “H”). After the selected level flashes 5 times and stays
solid on, the temperature level is set successfully.
4. Set Auto Off Timer: Press the Mode Button. When “* hrs”
starts to flash on the bottom right of the screen, press the
Timer Button to select timer from 1-3hrs. After the selected
time flashes 5 times and stays solid on, the auto off timer is
set successfully.
5. After all settings are done, the blanket will start working. But
the screen backlight will turn off in few seconds. Press any
button to turn the backlight on again.
6. To turn off the blanket, press the ON/OFF (Power) Button
when the screen backlight is on.
Problem Cause Solution
The appliance
does not warm
up.
The appliance is
not connected to
power.
Insert the power
plug into the
power socket and
switch on the
appliance.
The appliance is
not switched on.
Switch on the
appliance.
The appliance is
defective.
Please contact
Homech customer
service.
The letter “P” is
shown on the
controller display
screen or the
display does not
light up.
The blanket part
and the controller
are not correctly
connected.
Unplug the power
plug, properly plug
the blanket into
the controller, re-
switch on the
controller.
The appliance is
defective.
Please contact
Homech customer
service.
The letter "E" is
shown on the
controller display
screen.
The blanket/
controller has
overheating
protection.
Unplug the power
plug, spread out
the blanket and
let it cool down,
then re-switch on
the controller. If
you can not
troubleshoot, the
blanket is
damaged.
The blanket
heating element
has been
damaged due to
overheating, the
controller has
blown the Over-
Temp thermal
fuse.
The blanket is
damaged. Need
to be scrapped.
www.homech.net
13121110987
·When storing the appliance, allow it to cool down. Store the
unit in a clean and dry place.
Table of contents
Popular Motorcycle Accessories manuals by other brands
Petzl
Petzl SIROCCO manual
probrake
probrake TR10-2 Mounting instruction
Engelbert Strauss
Engelbert Strauss 75.76.651 operating instructions
hepco & becker
hepco & becker 42139521 00 01 quick start guide
Royal Enfield
Royal Enfield Himalayan Series Fitting instructions
Donner TECH
Donner TECH Tenere 700 Mounting instructions
