HOMEDEPOT C-1368-1B User manual

MANUAL
Model: C-1368-1B
aofis.ser[email protected]
[phone] | [phone]
INSTRUCTION

ASSEMBLY GUIDE
Congratulations, you are now the owner of a brand new home & office chair!
To best enjoy the comfort of the chair, you have to put it together first! This assembly guide
will take you through the assembly process. To make sure the assembly goes well,
please follow the instructions, and especially the important safety information.
It is possible to assemble the chair on your own, but it is recommended to have a
second person to make it easier and safer.
Please check if there are any missing parts from the package before starting. If
there is any issue, please don't hesitate to drop us an email and we'll help you out
ASAP. If you run into any difficulty when assembling the chair, remember to check
out the assembly video to see if you've missed anything. If you're unable to resolve
the problem, just send us an email and our support team will assist you.
WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure to
follow this warning can result in serious injury to yourself or others.
[email protected]
[phone] | [phone]
2

Package List
Without further ado, we kindly suggest you to list all parts needed
for the chair first.
3
Backrest
Mechanism Gas Lift Base
Legs BoltsCasters
Bolts
(1)*1 (2)*1 (3)*1(L)*1(R)
(4)*1 (5)*1 (6)*1
(7)*5 (8)*5 (9)*10
(10)*4
Seat Cushion Armrests
[email protected]
[phone] | [phone]
Bolts
(12)*6
(13)*1
Wrench
Bolts
(11)*4

Assembly Instruction
Step 1:
Turn the Base (6) upside down,
then insert Base Legs (7) one
by one to Base.
Use the Wrench (13) to screw Ten
Bolts (9) into the pre-drilled
screw holes to fix the Base and
the Base Legs.
1
3
2
[email protected]
[phone] | [phone]
4
(9)×2
(6)
(7)
Turn the Base (6) upside down,
then both hands are forced at the
same time to press the Casters
(8) into the holes at the end
of each Base Leg.
Step 2:
2
Insert the Gas Lift (5) into
the center hole of the Base.
Step 3: (5)

Turn the Seat Cushion (2)
upside down and align the
hole position of the Armrest
(3)*1(L)*1(R) with the
pre-drilled hole position
under the Seat Cushion.
Attach the Armrest (3)*1(L)*1(R)
to the Seat Cushion (2) with Six
Bolts (12), using the Wrench (13).
All bolts do not need to be tightened,
they only need to be fixed in half.
Attach the Mechanism (4) to the
Seat Cushion（2）using Four
Bolts (10), tighten all the bolts
with the Wrench (13).
4
5
5
Note 1: The "Front" mark on the Armrests and the "Front" mark on the
Seat Cushion should be in the same direction.
Note 2: Armrests are labeled with an "L" (left) or "R" (right) to show which
side they should be placed on.
5
Step 5:
Step 4:
[email protected]
[phone] | [phone]
50%
(2)
(3)
(12)×6
(2)
(10)×4

6
7
6
Insert the slot on the back of the
mechanism behind the cushion
into the Gas Lift.
Step 6:
This is to fix the Backrest(1) on the
Armrest(3)*1(R), use a Wrench(13)
to twist a Screw in(B1) don't tighten
the screw(11)*1 tightly.
Step 7:
[email protected]
[phone] | [phone]
6
(1)
B1
B2
(9)

[email protected]
[phone] | [phone]
8
9
Make sure all bolts and screws are fully tightened before using chair.
Lubricate all moving parts and tighten all bolts/screws every 6 month
or whenever needed.
CAUTION:
Use the wrench(13) to make
the left and right two
screws(11)into (B2), and then
tighten all the screws.
Step 9:
Step 8:
This is to fix the Backrest(1)
on the Armrest(3)*1(L) use a
Wrench(13) to twist a Screw
in (B1),don't tighten the
screw(11)*1 tightly.
B1
B2
(1)
(9)
B1
B2
B1
B2
(1)
(9)
(9)
7

Instructions For Use
7
1. Seat Height: Paddle-shaped lever on the right side
To lower:
While seated, lift lever up.
To raise:
While taking your weight off chair,
lift lever up.
* At the proper height, your feet should rest flat on the floor.
[email protected]
[phone] | [phone]
2. Padded Flip-up Arms
The padded feature allows you to rest
comfortably.
The armrests of the office chair have
a flip up design, you could customize
them according to your needs.
8

[email protected]
[phone] | [phone]
3. Operating the rocking function
To let your chair tilt back, pull the
control handle out.
To stop your chair from tilting, sit
forward, then push the control
handle in.
9

Safety And Maintenance
Safety Information
9
Do not stand on the chair, Do Not use the chair as a stepladder.
Use this product for seating one person at a time.
Do not use the chair unless all bolts and screws are firmly secured.
Avoid contact with sharp objects to prevent puncturing the fabric.
Every 6 months, check all bolts and screws to ensure they are tight.
To clean, spot clean only using a damp towel and mild cleaner, first
test on a small, unseen area of fabric.
Chair weight limit not to exceed 250 lbs.
Sit in the center of the
chair, with your back to
the backrest
Do not push the chair
around when a person
is sitting in it
Do not push down on
the backrest when a
person is reclined
Do not place all your
weight on only the
backrest
Do not sit at the front
edge of the chair Do not stand on the chair Do not use the chair with more than one
person
[email protected]
[phone] | [phone]
10