HOMEDEPOT L-DN366SAL-3-A User manual

1
Swivel Chair
Item# L-DN366SAL-3-A
WARNING:
Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the area of the Chair construction.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety
precautions should always be followed to reduce the risk of personal injury and damage to
the product. Please read all instructions before assembly and use.
Check all bolts for tightness before use. IMPORTANT - check and tighten bolts often to keep
them secure!

2
No Description Qty
A Chair Seat 1
BIron Support
˄Pre-assembled on C˅1
C Chair Base 1
D Cushion 1
AA Bolt M8*40 4
BB Bolt M8*35
(Pre-assembled ) 4
CC Spring Washer M8
(4 Pre-assembled) 8
DD Flat Washer M8
(4 Pre-assembled) 8
EE Nut M8 (4 Pre-assembled) 8
FF BigWasher
(2 Pre-assembled) 6
GG Spring Steel Board
(2 Pre-assembled) 2
HH Wrench M8 1
II Plastic Cap (Pre-assembled
on C) 1
Step1: Align the assembly holes on Iron Support (B) and Chair Seat (A) and attach them with
Bolt (AA), Big Washer (FF), Flat Washer (DD), Spring Washer (CC) and Nut (EE). Use Wrench
(HH) to lock the Bolts. LOCK ALL BOLTS TIGHTLY. (See Fig. 1)
$
%
F
'
$$$))
$
%))
''
&& ((
**
Parts List
Fig.1

3
Care & Maintenance
Before using, clean the Chair completely with a soft dry towel. Do not place your Chair in wet conditions where
there is a risk of rust developing. When not in use, wipe free of any dirt or loose objects, wash with a mild solution
of soap and water; rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. When
not in use, store in a cool, dry location away from sunlight.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof
of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is
non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations
on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights,
and you may also have other rights, which vary from state to state.
Step 2: Put Cushion (D) on the
seat. Stick the Velcro. (See Fig.
2). Assembly completed!
Fig.2

Round Table
Item# L-DN366SAL-3- A
WARNING:
Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the area of the Table construction.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety
precautions should always be followed to reduce the risk of personal injury and damage to
the product. Please read all instructions before assembly and use.
Check all bolts for tightness before use. IMPORTANT - check and tighten bolts often to keep

2
No Description Qty
AUmbrella Hole Cap 1
B Swivel Plate 1
C Table Top 1
D Leg 4
E Connecting Frame 1
AA Bolt M6×40 8
BB Spring Washer M6 8
CC Flat Washer M6 8
DD Bolt M8×20 8
EE Spring Washer M8 8
FF Flat Washer M8 8
GG Wrench M6 1
HH Wrench M8 1
II Foot Pad
(Pre-assembled on D) 4
Parts List

3
Step 1: Attach the Connecting Frame (E) to Leg (D) with Bolt (AA), Spring Washer (BB) and
Flat Washer (CC) by using the Wrench (GG). Be careful do not lock tight.
Step 2: Attached the Leg ( D) and Table Top (C) using Bolt (DD), Spring Washer (EE) and
Flat Washer (FF) by using Wrench (HH) to lock tight.
Step 3: Turn over the Table, tighten all the bolts. (Adjust the Foot Pad slightly). Put Umbrella Hole Cap
(A) and Swivel Plate (B) on Table Top (C). Swivel to adjust the Plate (B). Assembly completed!

4
Care & Maintenance
Before using, clean the Table completely with a soft dry towel. Do not place your Table in wet conditions where
there is a risk of rust developing. When not in use, wipe free of any dirt or loose objects, wash with a mild solution
of soap and water; rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. When
not in use, store in a cool, dry location away from sunlight.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof
of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is
non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations
on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights,
and you may also have other rights, which vary from state to state.