HOMEDEPOT SH-4830M User manual

ITEM NO.: SH-4830M
REVISED FEB 12, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: MISSION BOOKCASE 30X48
: SH-4830M

ITEM NO.: SH-4830M
REVISED FEB 12, 2015
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
product. Protect the surface of the product with cloth if you are using any product with rubber feet or
base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: SH-4830M
REVISED FEB 12, 2015
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
N
O
Descriptio
n
Qt
y Sketch N O
Descriptio
n
Qt
y Sketch
A Top 1 B
Bottom
Shelf 1
C Adjustabl
e shelf 3 D
Side
frame
(L-R)
2
E Rail 4
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 bolt
(M6x30mm) 8
2 Flat Washer
(ɸ6.5x13mm) 8
3 Lock Washer
(ɸ6.5x11mm) 8 4 Allen Key
(M4x80mm) 1
5 Long Screw
(M4x30mm) 13
6 Short Screw
(M3.5x15mm) 14
7 Bracket 12 8 Steel band 1

ITEM NO.: SH-4830M
REVISED FEB 12, 2015
Printed in Vietnam
- 4 -
STEP 1
Attach the Bottom Shelf (B) and the Top (A) to one side frame (D) with bolts (1), and washers (2)
and (3) as shown below. Tighten with Allen key (4).
th
STEP 2
Insert Rails (E) into Side frames (D) as shown below.
Attach other Side frame (D) to unit with Bolts (1) and washers (2) and (3). Tighten with Allen key (4).

ITEM NO.: SH-4830M
REVISED FEB 12, 2015
Printed in Vietnam
- 5 -
STEP 3
Attach Rails (E ) to the top (A) and Bottom shelf (B), with screws (5), as shown below. Tighten with a
screwdriver.
STEP 4
Attach brackets (7) to the unit. Place the Adjustable shelves (C ) on the brackets, attach with screws
(6), as shown below. Tighten with a screwdriver.
Attach the Steel band (8) to the unit with screws (6). Then attach the Steel band to the wall with
the Long screw (5) as shown below (to secure the product and prevent tipping).