Honeywell OWA 100 OneWireless User manual

OneWireless Adapter
Professional Installation Guide
34-XY-25-48
Revision 1
May 2011

ii OneWireless Adapter Professional Installation Guide Revision 1
May 2011
Notices and Trademarks
Copyright 2011 by Honeywell International Inc.
Revision 1, May 2011
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may
be stated in its written agreement with and for its customers.
In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and
specifications in this document are subject to change without notice.
Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.
Other brand or product names are trademarks of their respective owners.
Honeywell Process Solutions
1860 West Rose Garden Lane
Phoenix, Arizona 85027

Revision 1 OneWireless Adapter Professional Installation Guide iii
May 2011
About This Document
This document outlines professional installation requirements for the Honeywell OneWireless Adapter.
Professional installation is required to comply with certification agency and legal requirements. This document
must be adhered to for all installations of the Honeywell OneWireless Adapter.
Honeywell does not recommend using devices for critical control where there is a single point of failure or where
single points of failure result in unsafe conditions. OneWireless is targeted at open loop control, supervisory
control, and controls that do not have environmental or safety consequences. As with any process control solution,
the end-user must weigh the risks and benefits to determine if the products used are the right match for the
application based on security, safety, and performance. Additionally, it is up to the end-user to ensure that the
control strategy sheds to a safe operating condition if any crucial segment of the control solution fails.
Revision Information
Document Name
Document ID Revision
Number Publication Date
OneWireless Adapter Professional Installation Guide 34-XY-25-48 Revision 1 May 2011
References
The following list identifies all documents that may be sources of reference for material discussed in this publication.
Document Title
Getting Started with Honeywell OneWireless Solutions

iv OneWireless Adapter Professional Installation Guide Revision 1
May 2011
Support and contact info
United States and Canada
Contact: Honeywell Process Solution
Global Technical Support - Phone: [phone]
Customer Service (HFS) - Phone: [phone]
Outside United States - Phone: [phone]
Calls are answered by dispatcher between 6:00 am and 4:00 pm Mountain Standard
Time. Emergency calls outside normal working hours are received by an answering
service and returned within one hour.
Email support: [email protected]
Mail: Honeywell Process Solutions
1860 West Rose Garden Lane,
Phoenix, AZ, 85027
EuropeContact: Honeywell TAC-EMEA
Phone: [phone]
Facsimile: [phone]
Mail: TAC-BE02
Hermes Plaza
Hermeslaan, 1H
B-1831 Diegem, Belgium
Pacific Contact: Honeywell Global TAC – Pacific
Phone: [phone] (toll free within Australia)
[phone] (outside Australia)
Facsimile: [phone]
Mail: Honeywell Limited Australia
5 Kitchener Way
Burswood 6100, Western Australia
Email: [email protected]
India Contact: Honeywell Global TAC – India
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Automation India Ltd.
56 and 57, Hadapsar Industrial Estate
Hadapsar, Pune –411 013, India
Email: [email protected]
Korea Contact: Honeywell Global TAC – Korea
Phone: [phone]
[phone]
Facsimile: [phone]
Mail: Honeywell Co., Ltd
17F, Kikje Center B/D,
191, Hangangro-2Ga
Yongsan-gu, Seoul, 140-702, Korea
Email: [email protected]

Revision 1 OneWireless Adapter Professional Installation Guide v
May 2011
People’s Republic of China
Contact: Honeywell Global TAC – China
Phone: [phone]
Mail: Honeywell (China) Co., Ltd
33/F, Tower A, City Center, 100 Zunyi Rd.
Shanghai 200051, People’s Republic of China
Email: [email protected]
Singapore
Contact: Honeywell Global TAC – South East Asia
Phone: [phone]
Facsimile: [phone]
[phone]
Mail: Honeywell Private Limited
Honeywell Building
17, Changi Business Park Central 1
Singapore 486073
Email: [e-mail]
Taiwan Contact: Honeywell Global TAC – Taiwan
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Taiwan Ltd.
17F-1, No. 260, Jhongshan 2nd Road.
Cianjhen District
Kaohsiung, Taiwan, ROC
Email: [email protected]
Japan Contact: Honeywell Global TAC – Japan
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Japan Inc.
New Pier Takeshiba, South Tower Building,
20th Floor, 1-16-1 Kaigan, Minato-ku,
Tokyo 105-0022, Japan
Email: Global-TAC-Jap[email protected]
World Wide Web
Honeywell Solution Support Online:
http://www.honeywell.com/ps/hfs
Elsewhere
Call your nearest Honeywell office.
Training Classes
Honeywell Automation College:
http://www.automationcollege.com

vi OneWireless Adapter Professional Installation Guide Revision 1
May 2011
Symbol Definitions
The following table lists those symbols used in this document to denote certain conditions.
Symbol Definition
ATTENTION: Identifies information that requires special consideration.
TIP: Identifies advice or hints for the user, often in terms of performing a task.
CAUTION Indicates a situation which, if not avoided, may result in equipment or work (data) on
the system being damaged or lost, or may result in the inability to properly operate
the process.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practices.
CAUTION symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could
result in serious injury or death.
WARNING symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS
LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.
ESD HAZARD: Danger of an electro-static discharge to which equipment may be
sensitive. Observe precautions for handling electrostatic sensitive devices.
Protective Earth (PE) terminal: Provided for connection of the protective earth
(green or green/yellow) supply system conductor.
Functional earth terminal: Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to Protective Earth at the
source of supply in accordance with national local electrical code requirements.
Earth Ground:Functional earth connection. NOTE: This connection shall be
bonded to Protective Earth at the source of supply in accordance with national and
local electrical code requirements.
Chassis Ground: Identifies a connection to the chassis or frame of the equipment
shall be bonded to Protective Earth at the source of supply in accordance with
national and local electrical code requirements.
continued

Revision 1 OneWireless Adapter Professional Installation Guide vii
May 2011
Symbol Description
The Factory Mutual®Approval mark means the equipment has
been rigorously tested and certified to be reliable.
The Canadian Standards mark means the equipment has been
tested and meets applicable standards for safety and/or
performance.
The Ex mark means the equipment complies with the requirements
of the European standards that are harmonized with the 94/9/EC
Directive (ATEX Directive, named after the French "ATmosphere
EXplosible").
For radio equipment used in the European Union in accordance
with the R&TTE Directive the CE Mark and the notified body (NB)
identification number is used when the NB is involved in the
conformity assessment procedure. The alert sign must be used
when a restriction on use (output power limit by a country at certain
frequencies) applies to the equipment and must follow the CE
marking.
The C-Tick mark is a certification trade mark registered to ACMA
(Australian Communications and Media Authority) in Australia under
the Trade Marks Act 1995 and to RSM in New Zealand under
section 47 of the NZ Trade Marks Act. The mark is only to be used
in accordance with conditions laid down by ACMA and RSM. This
mark is equal to the CE Mark used in the European Union.
N314 directly under the logo is Honeywell’s unique supplier
identification number.
The ISA100 Wireless Compliant logo indicates the device has
received ISA100.11a conformance certification and is registered
with the Wireless Compliance Institute, assuring device
interoperability.

viii OneWireless Adapter Professional Installation Guide Revision 1
May 2011

Revision 1 OneWireless Adapter Professional Installation Guide ix
May 2011
Contents
Support and contact info........................................................................................................................iv
1. DESIGNATION, SCOPE AND PREFACE .............................................................1
1.1 Designation....................................................................................................................................1
1.2 Scope..............................................................................................................................................1
1.3 Preface ...........................................................................................................................................1
1.4 Site survey.....................................................................................................................................1
1.5 Abbreviations & Definitions.........................................................................................................2
2. FEDERAL COMMUNICATION COMMISSION (FCC) ...........................................4
2.1 FCC Compliance Statement.........................................................................................................4
2.2 Industry Canada (IC).....................................................................................................................4
2.2.1 IC Compliance Statements.....................................................................................................................4
2.2.2 RF Safety Statement ..............................................................................................................................4
2.3 FCC and Industry Canada (IC) Identification Numbers.............................................................5
2.4 Intended Country Usage...............................................................................................................6
2.4.1 NORTH AMERICA .................................................................................................................................6
2.4.2 EUROPEAN UNION...............................................................................................................................6
3. ONEWIRELESS ADAPTER GENERAL DESCRIPTION.......................................7
3.1 Intended Used................................................................................................................................7
4. PRODUCT SPECIFICATION.................................................................................8
4.1 ISA100 Radio, 2.4 GHz..................................................................................................................8
4.2 OneWireless Adapter User Environment....................................................................................8
4.3 OneWireless Adapter Power Specifications ..............................................................................9
4.4 Weight ............................................................................................................................................9
4.5 Dimensions....................................................................................................................................9
5. APPROVED ANTENNA TYPES/GAINS..............................................................10
5.1 Antenna Details...........................................................................................................................10
6. EQUIVALENT ISOTROPICALLY RADIATED POWER (EIRP)...........................11
6.1 EIRP LIMITS.................................................................................................................................11
7. SETTING TX POWER..........................................................................................13
7.1 TX Power Setting.........................................................................................................................13

Contents
Symbol Definitions
x OneWireless Adapter Professional Installation Guide Revision 1
May 2011
8. AGENCY LABEL INFORMATION.......................................................................14
8.1 External FCC/IC Labels...............................................................................................................14
8.1.1 50016195-001 – Transmitters with FHSS Radios ................................................................................14
8.1.2 Internal FCC/IC Labels.........................................................................................................................14
9. RF SAFETY, MAXIMUM PERMISSIBLE EXPOSURE (MPE) STATEMENT......15
9.1 MPE Statement............................................................................................................................15
10. AGENCY COMPLIANCE.....................................................................................16
10.1 Radio and EMC Certifications................................................................................................16
10.1.1 Federal Communication Commission (FCC)........................................................................................16
10.1.2 Industry Canada (IC)............................................................................................................................16
10.1.3 European Telecommunications Standards Institute (ETSI)..................................................................16
10.2 Product Safety Agency Certifications...................................................................................16
10.2.1 Canadian Standards Association (CSA) ..............................................................................................16
10.2.2 Factory Mutual (FM).............................................................................................................................17
10.2.3 European ATEX Certification (ATEX)...................................................................................................17
10.2.4 IECEx Certification...............................................................................................................................18
10.2.5 European Union Certification (CE-mark)..............................................................................................18
11. REFERENCE DOCUMENTS ...............................................................................19
11.1 OneWireless reference documentation.................................................................................19

Contents
Tables
Revision 1 OneWireless Adapter Professional Installation Guide xi
May 2011
Tables
Table 1-1 –Table of Abbreviations and Definitions........................................................................................2
Table 4-1 Specifications ISA100 Radio Module in OneWireless Adapter.....................................................8
Table 4-2 User Environment Specifications for OneWireless Adapter Transmitter ......................................8
Table 5-1 Approved Antenna Types/Gains .................................................................................................10
Table 6-1 Maximum EIRP Limits for DSSS and ISA100 Radios.................................................................11
Table 6-2– Factory Transmit Power Settings for FCC, IC and ETSI...........................................................12
Table 11-1 – Reference documents............................................................................................................19

Contents
Figures
xii OneWireless Adapter Professional Installation Guide Revision 1
May 2011
Figures
Figure 4-1 OneWireless Adapter Dimensions...............................................................................................9

1. Designation, Scope and Preface
1.1. Designation
Revision 1 OneWireless Adapter Professional Installation Guide 1
May 2011
1. Designation, Scope and Preface
1.1 Designation
This document is valid for the OneWireless Adapter (OWA). The OneWireless Adapter is intended to be
directly connected to a HART device or network and provide a wireless interface between the wired
HART network and the wireless ISA100 network.
1.2 Scope
This document outlines professional installation requirements for the Honeywell OneWireless Adapter.
Professional installation is required to comply with certification agency and legal requirements. This
document must be adhered to for all installations of the Honeywell OneWireless Adapter.
1.3 Preface
This manual covers professional installation of the Honeywell OneWireless Adapter. See the Getting
Started with Honeywell OneWireless, Honeywell OneWireless Planning Guide and Honeywell
OneWireless Adapter User’s Guides for general information on overall system implementation,
configuration, and management of these devices.
The OneWireless Adapter is classified by the FCC as a device that must be professionally installed.
1.4 Site survey
It is assumed for the purposes of this document that a site survey has been performed and that the
OneWireless Adapter is installed in a location consistent with the Model Selection Guide selection. Any
changes to the location as a result of the actual installation of the OneWireless Adapters into the site may
require that the TX power setting of the radio board needs to be adjusted from the factory setting in order
to maintain agency approvals. See Equivalent Isotropically Radiated Power (EIRP) and Setting TX Power
for more information.

1. Designation, Scope and Preface
1.5. Abbreviations & Definitions
2 OneWireless Adapter Professional Installation Guide Revision 1
May 2011
1.5 Abbreviations & Definitions
The term Honeywell OneWireless Adapter will be used to describe the composite unit which includes the
Honeywell ISA100 RF Module and all subassemblies housed within the OneWireless Adapter enclosure.
Table 1-1 –Table of Abbreviations and Definitions
ACMA Australian Communications and Media Authority
AD Authentication Device
ATEX Potentially Explosive Atmospheres Directive
AWG American Wire Gauge
Co-located Two or more radios transmitting simultaneously and with less than 20cm
of separation distance.
CSA Canadian Standards Association
DCS Distributed Control System
DSSS Direct Sequence Spread Spectrum
EMC Electromagnetic Compatibility
ETSI European Telecommunications Standards Institute
EU European Union
FCC Federal Communications Committee
FHSS Frequency-Hopping Spread Spectrum
FM Factory Mutual
FSK Frequency Shift Keying
GFSK Gaussian Frequency Shift Keying
GTS Honeywell Global Technical Services
IC Industry Canada
IEEE Institute of Electrical and Electronics Engineers
IR Infrared
IrDA Infrared Data Association
ISA100 International Society of Automation open-standard wireless networking
technology
HART Highway Addressable Remote Transducer Communications Protocol
MIC Japan Ministry of Internal Affairs and Communications
MPE Maximum Permissible Exposure
MSG Honeywell Model Selection Guide

1. Designation, Scope and Preface
1.5. Abbreviations & Definitions
Revision 1 OneWireless Adapter Professional Installation Guide 3
May 2011
NA North America – United States of America and Canada
NEMA National Electrical Manufacturers Association
OQPSK Offset Quadrature Phase-Shift Keying
OWA OneWireless Adapter
TELEC Japan Telecom Engineering Center
TIIS Japan Technology Institution of Industrial Safety
TX Transmit
Wi-Fi Wireless Local Area Network based on IEEE 802.11 Specifications
WNSIA Wireless Network for Secure Industrial Application

2. Federal Communication Commission (FCC)
2.1. FCC Compliance Statement
4 OneWireless Adapter Professional Installation Guide Revision 1
May 2011
2. Federal Communication Commission (FCC)
2.1 FCC Compliance Statement
This device complies with Part 15 of FCC Rules and Regulations. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radiofrequency energy and, if not installed and used in accordance with these instructions, may
cause harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Intentional or unintentional changes or modifications must not be made to the OneWireless Adapter
unless under the express consent of the party responsible for compliance. Any such modifications
could void the user’s authority to operate the equipment and will void the manufacturer’s warranty.
2.2 Industry Canada (IC)
2.2.1 IC Compliance Statements
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropic radiated power (EIRP) is not more than that permitted for successful
communication.
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
This Class A digital apparatus complies with Canadian ICES-003.
French: Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
2.2.2 RF Safety Statement
To comply with FCC’s and Industry Canada’s RF exposure requirements, the following antenna
installation and device operating configurations must be satisfied.
Remote Point-to-Multi-Point antenna(s) for this unit must be fixed and mounted on outdoor permanent
structures with a separation distance between the antenna(s) of greater than 20cm and a separation
distance of at least 20cm from all persons.
Furthermore, when using integral antenna(s) the OneWireless Adapter unit must not be co-located
with any other antenna or transmitter device and have a separation distance of at least 20cm from all
persons.

2. Federal Communication Commission (FCC)
2.3. FCC and Industry Canada (IC) Identification Numbers
Revision 1 OneWireless Adapter Professional Installation Guide 5
May 2011
2.3 FCC and Industry Canada (IC) Identification Numbers
This information is shown on the label attached to each RF Module.
Honeywell OneWireless Adapter Radio Module Identification
Honeywell Identification for Intrinsically Safe RF Modules: 50025034-002
Honeywell OneWireless Adapter Radio Limited Modular Approval
Federal Communication Commission Identification for Intrinsically Safe RF Modules:
S5750016517
Industry Canada Identification for Intrinsically Safe RF Modules: 573I-50025034

2. Federal Communication Commission (FCC)
2.4. Intended Country Usage
6 OneWireless Adapter Professional Installation Guide Revision 1
May 2011
2.4 Intended Country Usage
2.4.1 NORTH AMERICA
Country ISO 3166 2 letter code
Canada CA
United States US
2.4.2 EUROPEAN UNION
Country ISO 3166
2 letter code Country ISO 3166 2 letter code
Austria AT Latvia LV
Belgium BE Liechtenstein LI
Bulgaria BG Lithuania LT
Cyprus CY Malta MT
Czech Republic CZ Netherlands NL
Denmark DK Norway NO
Estonia EE Poland PL
Finland FI Portugal PT
France FR Romania RO
Germany DE Slovakia SK
Greece GR Slovenia SI
Hungary HU Spain ES
Iceland IS Sweden SE
Ireland IE Switzerland CH
Italy IT United Kingdom BG

3. OneWireless Adapter General Description
3.1. Intended Used
Revision 1 OneWireless Adapter Professional Installation Guide 7
May 2011
3. OneWireless Adapter General Description
3.1 Intended Used
The OneWireless Adapter is a key component of the Honeywell Wireless Network for Secure Industrial
Application (WNSIA). These transmitters are available for various sensor types including Digital Inputs,
Temperature, High Level Analog Inputs, Pressure and Corrosion. The OneWireless Adapter uses a low-
powered ISA100 2.4 GHz radio to communicate with Radio Infrastructure and Gateway devices that are
connected to a wired DCS network.

4. Product Specification
4.1. ISA100 Radio, 2.4 GHz
8 OneWireless Adapter Professional Installation Guide Revision 1
May 2011
4. Product Specification
4.1 ISA100 Radio, 2.4 GHz
WARNING!
The OneWireless Adapter must be Professionally Installed in accordance with the
requirements specified in this document. See Section 10, for professional
installation maximum TX power setting requirements. Only the specified TX
power settings, antenna types and gains and cable lengths (attenuation) as
outlined in this document are valid for OneWireless Adapter installations.
Table 4-1 Specifications ISA100 Radio Module in OneWireless Adapter
4.2 OneWireless Adapter User Environment
Table 4-2 User Environment Specifications for OneWireless Adapter Transmitter
Item Specification
Operating Temperature: –40ºC to +85ºC (–40°F to +185°F)
Storage Temperature: –40ºC to +85ºC (–40°F to +185°F)
Operating Humidity: 0 to 100% RH
Other Environmental specifications and information may be found in the appropriate Instrument
Specification available on the Honeywell website.
Item Specification
Wireless Standard FCC 15.247 / IEEE 802.15.4 Direct Sequence Spread Spectrum (DSSS),
2.4 GHz
Data Rates and
Modulation Data Rate: 250 kbps
Modulation: Offset Quadrature Phase-Shift Keying (OQPSK – DSSS)
Frequency Band 2,405 – 2,475 MHz
Module Transmit Power Maximum: 20 dBm
(Maximum transmit power will vary by channel)
Receive Sensitivity
(typical) -100 dBm