Honeywell OWA 100 OneWireless User manual

OneWireless
OWA 100 OneWireless Adapter
User Manual
34-XY-25-40
Revision 2
July 2011

ii OWA 100 Adapter User Manual Rev. 2
July 2011
Notices and Trademarks
Copyright 2011 by Honeywell International Inc.
Revision 2 July 2011
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may
be stated in its written agreement with and for its customers.
In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and
specifications in this document are subject to change without notice.
Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.
HART®is a trademark of the Hart Communication Foundation.
Other brand or product names are trademarks of their respective owners.
Honeywell Process Solutions
1860 West Rose Garden Lane
Phoenix, AZ 85027

Rev. 2 OWA 100 Adapter User Manual iii
July 2011
About This Document
This document describes mounting, installation, wiring, operation and maintenance of the OWA 100 Wireless
Adapter are covered in other documents.
Honeywell does not recommend using devices for critical control where there is a single point of failure or where
single points of failure result in unsafe conditions. OneWireless is targeted at open loop control, supervisory
control, and controls that do not have environmental or safety consequences. As with any process control solution,
the end-user must weigh the risks and benefits to determine if the products used are the right match for the
application based on security, safety, and performance. Additionally, it is up to the end-user to ensure that the
control strategy sheds to a safe operating condition if any crucial segment of the control solution fails.
Revision Information
Document Name Document ID Revision
Number Publication Date
OWA 100 Adapter User Manual 34-XY-25-40 1 January 2011
Release version 34-XY-25-40 2 July 2011
References
The following list identifies all documents that may be sources of reference for material discussed in this
publication.
Document Title
Getting Started with Honeywell OneWireless Solutions
OneWireless Wireless Builder User’s Guide
OneWireless Builder Parameter Reference
Support and contact info
United States and Canada
Contact: Honeywell Process Solution
Global Technical Support: Phone [phone].
Honeywell Field Solutions Customer Support: Phone [phone]
Calls are answered by dispatcher between 6:00 am and 4:00 pm Mountain Standard Time.
Emergency calls outside normal working hours are received by an answering service and
returned within one hour.
Outside US: Phone [phone]
Email: [email protected]
Mail: Honeywell Process Solutions
1860 West Rose Garden Lane
Phoenix, AZ, 85027

iv OWA 100 Adapter User Manual Rev. 2
July 2011
EuropeContact: Honeywell TAC-EMEA
Phone: [phone]
Facsimile: [phone]
Mail: TAC-BE02
Hermes Plaza
Hermeslaan, 1H
B-1831 Diegem, Belgium
Pacific Contact: Honeywell Global TAC – Pacific
Phone: [phone] (toll free within Australia)
[phone] (outside Australia)
Facsimile: [phone]
Mail: Honeywell Limited Australia
5 Kitchener Way
Burswood 6100, Western Australia
Email: [email protected]
India Contact: Honeywell Global TAC – India
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Automation India Ltd.
56 and 57, Hadapsar Industrial Estate
Hadapsar, Pune –411 013, India
Email: [email protected]
Korea Contact: Honeywell Global TAC – Korea
Phone: [phone]
[phone]
Facsimile: [phone]
Mail: Honeywell Co., Ltd
17F, Kikje Center B/D,
191, Hangangro-2Ga
Yongsan-gu, Seoul, 140-702, Korea
Email: [email protected]
People’s Republic of China
Contact: Honeywell Global TAC – China
Phone: [phone]
Mail: Honeywell (China) Co., Ltd
33/F, Tower A, City Center, 100 Zunyi Rd.
Shanghai 200051, People’s Republic of China
Email: [email protected]

Rev. 2 OWA 100 Adapter User Manual v
July 2011
Singapore
Contact: Honeywell Global TAC – South East Asia
Phone: [phone]
Facsimile: [phone]
[phone]
Mail: Honeywell Private Limited
Honeywell Building
17, Changi Business Park Central 1
Singapore 486073
Email: [e-mail]
Taiwan Contact: Honeywell Global TAC – Taiwan
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Taiwan Ltd.
17F-1, No. 260, Jhongshan 2nd Road.
Cianjhen District
Kaohsiung, Taiwan, ROC
Email: [email protected]
Japan Contact: Honeywell Global TAC – Japan
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Japan Inc.
New Pier Takeshiba, South Tower Building,
20th Floor, 1-16-1 Kaigan, Minato-ku,
Tokyo 105-0022, Japan
Email: Global-TAC-Jap[email protected]
World Wide Web
Honeywell Solution Support Online:
http://www.honeywell.com/ps
Elsewhere
Outside US: Phone [phone] or call your nearest Honeywell office.
Training Classes
Honeywell Automation College:
http://www.automationcollege.com

vi OWA 100 Adapter User Manual Rev. 2
July 2011
Symbol Definitions
The following table lists those symbols used in this document to denote certain conditions.
Symbol Definition
ATTENTION: Identifies information that requires special consideration.
TIP: Identifies advice or hints for the user, often in terms of performing a task.
CAUTION
Indicates a situation which, if not avoided, may result in equipment or work (data) on
the system being damaged or lost, or may result in the inability to properly operate
the process.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practices.
CAUTION symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
ESD HAZARD: Danger of an electro-static discharge to which equipment may be
sensitive. Observe precautions for handling electrostatic sensitive devices.
Protective Earth (PE) terminal: Provided for connection of the protective earth
(green or green/yellow) supply system conductor.
continued
Symbol Description
The Factory Mutual®Approval mark means the equipment has
been rigorously tested and certified to be reliable.
The Canadian Standards mark means the equipment has been
tested and meets applicable standards for safety and/or
performance.
The Ex mark means the equipment complies with the requirements
of the European standards that are harmonised with the 94/9/EC
Directive (ATEX Directive, named after the French "ATmosphere
EXplosible").
For radio equipment used in the European Union in accordance
with the R&TTE Directive the CE Mark and the notified body (NB)
identification number is used when the NB is involved in the
conformity assessment procedure. The alert sign must be used
when a restriction on use (output power limit by a country at certain
frequencies) applies to the equipment and must follow the CE
marking.

Rev. 2 OWA 100 Adapter User Manual vii
July 2011
Symbol Description
The C-Tick mark is a certification trade mark registered to ACMA
(Australian Communications and Media Authority) in Australia under
the Trade Marks Act 1995 and to RSM in New Zealand under
section 47 of the NZ Trade Marks Act. The mark is only to be used
in accordance with conditions laid down by ACMA and RSM. This
mark is equal to the CE Mark used in the European Union.
N314 directly under the logo is Honeywell’s unique supplier
identification number.
Brazil – National Agency for telecommunications

viii OWA 100 Adapter User Manual Rev. 2
July 2011
Contents
Support and contact info .......................................................................................................................iii
1. INTRODUCTION....................................................................................................1
1.1 Safety Messages ...........................................................................................................................1
Warnings................................................................................................................................................................ 1
1.2 Purpose..........................................................................................................................................1
1.3 Scope..............................................................................................................................................1
1.4 OneWireless network overview...................................................................................................1
1.5 About the OWA 100 OneWireless Adapter.................................................................................2
Outputs .................................................................................................................................................................. 2
2. SPECIFICATIONS .................................................................................................3
2.1 European Union Usage.................................................................................................................3
2.2 Certifications and approvals........................................................................................................4
Provisioning Device ............................................................................................................................................... 5
2.3 Agency compliance information..................................................................................................6
FCC compliance statements .................................................................................................................................. 6
IC compliance statements...................................................................................................................................... 6
Radio Frequency (RF) statement........................................................................................................................... 6
European Union Conformity................................................................................................................................... 6
2.4 Honeywell European (CE) Declaration of Conformity (DoC)....................................................7
2.5 IECEx Conditions of Certification: ..............................................................................................9
2.6 ATEX Conditions for Safe Use:....................................................................................................9
3. CONFIGURATION...............................................................................................10
3.1 Safety Messages .........................................................................................................................10
Warnings.............................................................................................................................................................. 10
3.2 Installation ...................................................................................................................................11
Dimensions .......................................................................................................................................................... 12
3.3 Connecting to network ...............................................................................................................13
3.4 Configuration...............................................................................................................................13
4. OPERATION........................................................................................................18
4.1 Overview ......................................................................................................................................18
OWA 100 Adapter display modes ........................................................................................................................ 18
4.2 Provisioning device menus........................................................................................................20
Overview.............................................................................................................................................................. 20
Main menu ........................................................................................................................................................... 20
Security and Node Deployment ........................................................................................................................... 21
Device Local Configuration .................................................................................................................................. 23
Read Node Information........................................................................................................................................ 24
Advanced Options................................................................................................................................................ 26

Contents
Rev. 2 OWA 100 Adapter User Manual ix
July 2011
5. MAINTENANCE/REPAIR ....................................................................................28
5.1 Parts .............................................................................................................................................28
5.2 Replacing the battery..................................................................................................................28
When to replace ...................................................................................................................................................28
Tools required ......................................................................................................................................................28
Procedure.............................................................................................................................................................28
6. CERTIFICATION INSTALLATION REQUIREMENTS.........................................31
6.1 Certification Drawings................................................................................................................31
7. REFERENCE DATA ............................................................................................33
7.1 Product Specifications ...............................................................................................................33
Operating Conditions............................................................................................................................................33
Specifications .......................................................................................................................................................33
Physical Specifications .........................................................................................................................................34
Certifications.........................................................................................................................................................35

Contents
Tables
x OWA 100 Adapter User Manual Rev. 2
July 2011
Tables
Table 1 OWA 100 Adapter Display Modes..................................................................................................18
Table 2 Buttons for Device Local Configuration ..........................................................................................23
Table 3 Read Node Information ..................................................................................................................24
Table 4 Advanced Options ..........................................................................................................................27
Table 5 Battery replacement procedure ......................................................................................................30
Figures
Figure 1-1 OWA 100 Adapter Functional Diagram.......................................................................................2
Figure 3-1 Installation, Front view ...............................................................................................................11
Figure 3-2 Installation, Back view................................................................................................................11
Figure 3-3 Dimensions.................................................................................................................................12
Figure 3-4 System Wiring Diagram .............................................................................................................12
Figure 3-5 OWA 100 – TWO-WIRE CONFIGURATION .............................................................................13
Figure 3-6 OWA 100 – TWO-WIRE CONFIGURATION WITH RESISTOR ...............................................14
Figure 3-7 OWA 100 – 4-WIRE PASSIVE DEVICE CONFIGURATION.....................................................14
Figure 3-8 OWA 100 – 4-WIRE PASSIVE DEVICE CONFIGURATION WITH RESISTOR.......................15
Figure 3-9 OWA 100 – 4-WIRE ACTIVE DEVICE CONFIGURATION .......................................................15
Figure 3-10 OWA 100 – 4-WIRE ACTIVE DEVICE CONFIGURATION WITH NO 4-20 mA LOOP...........16
Figure 3-11 OWA 100 – AS A ROUTER, NO WIRED DEVICE ..................................................................16
Figure 3-12 REMOTE INSTALLATION .......................................................................................................17
Figure 4-1 Main menu..................................................................................................................................20
Figure 4-2 Security and Node Deployment .................................................................................................21
Figure 4-3 Device Local Configuration screen ............................................................................................23
Figure 4-4 Read Node Information ..............................................................................................................24
Figure 4-5 Advanced Options......................................................................................................................26
Figure 5-1 Battery replacement ...................................................................................................................29

1. Introduction
1.1. Safety Messages
Rev. 2 OWA 100 Adapter User Manual 1
July 2011
1. Introduction
1.1 Safety Messages
These instruction procedures may require special precautions to ensure the safety of the personnel
performing the operations. Information that potentially raises safety issues is indicated by a warning
symbol ( ). Please refer to the following safety messages before performing an operation preceded by
this symbol.
Warnings WARNING
Failure to follow these instructions could result in death or serious injury.
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
• Before connecting the OWA 100 OneWireless Adaptor in an explosive
atmosphere, make sure the instruments are installed in accordance with intrinsically
safe or nonincendive field wiring practices.
• Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
1.2 Purpose
This manual describes the Honeywell OneWireless OWA 100 Adapter installation, function, operation and
maintenance.
1.3 Scope
The manual includes:
Details of topics that relate uniquely to the Honeywell OWA 100 Adapter
This manual covers installation, mounting and wiring of the OneWireless OWA 100 Adapter.
1.4 OneWireless network overview
OneWireless is an all digital, serial, two-way communication mesh network that interconnects industrial
field sensors to a central system.
OneWireless has defined standards to which field devices and operator stations communicate with one
another. The communications protocol is built as an "open system" to allow all field devices and
equipment that are built to OneWireless standard to be integrated into a system, regardless of the device
manufacturer. This interoperability of devices using OneWireless technology is to become an industry
standard for automation systems.

1. Introduction
1.5. About the OWA 100 OneWireless Adapter
2 OWA 100 Adapter User Manual Rev. 2
July 2011
1.5 About the OWA 100 OneWireless Adapter
The OneWireless Adapet (OWA 100) is designed with an OneWireless interface to allow wired HART
devices to operate in a compatible distributed OneWireless system. The adapter will interoperate with any
OneWireless-registered device and provide the HART diagnostic and process information to any
ISA100.11a compliant system.
The OWA 100 Adapter includes OneWireless electronics for operating in a 2.4GHz network.
Outputs
The Process Variable (PV) is available for monitoring and alarm purposes. Available PV update rates are
5, 10, 30, 60 seconds and are set via the OneWireless application. Slower update rates extend battery life.
Figure 1 shows a block diagram of a OWA 100 Adapter’s operating functions.
Figure 1-1 OWA 100 Adapter Functional Diagram

2. Specifications
2.1. European Union Usage
Rev. 2 OWA 100 Adapter User Manual 3
July 2011
2. Specifications
2.1 European Union Usage
This product may be used in any of the following European Union nations.
Country ISO 3166
2 letter code Country ISO 3166 2 letter code
Austria AT Latvia LV
Belgium BE Liechtenstein LI
Bulgaria BG Lithuania LT
Cyprus CY Malta MT
Czech Republic CZ Netherlands NL
Denmark DK Norway NO
Estonia EE Poland PL
Finland FI Portugal PT
France FR Romania RO
Germany DE Slovakia SK
Greece GR Slovenia SI
Hungary HU Spain ES
Iceland IS Sweden SE
Ireland IE Switzerland CH
Italy IT United Kingdom BG

2. Specifications
2.2. Certifications and approvals
4 OWA 100 Adapter User Manual Rev. 2
July 2011
2.2 Certifications and approvals
Hazardous Location
Certifications CSA - USA and Canada
Intrinsic Safety
Class I, II, III Division 1, Groups C, D, E, F, & G; T4
Ex ia IIB; T4;
Ex tb IIIC T90°C IP66
Ambient Temperature: –40°C ≤Ta ≤+70°C
Enclosure: Type 4x/ IP46
Non Incendive
Class I, Division 2, Groups CD;
Class II, Division 2, Groups F & G; Suitable for Class III, Division 2; T4
Class I, Zone 2 AEx nA IIB, T4
Ex tb IIIC T90°C, IP66
Ambient Temperature: –40°C ≤Ta ≤+85°C
Enclosure: Type 4x/ IP46
IECEx DEKRA- Intrinsic Safety
Ex ia IIB, T4
Ex tb IIIC T90°C, IP66
Ambient Temperature: –40°C ≤Ta ≤+70°C
Enclosure: IP66
DEKRA- Non Sparking
Ex nA IIB T4, Gc
Zone 22, Ex tb IIIC T90°C IP66, Dc,
Ambient Temperature: –40°C ≤Ta ≤+85°C
Enclosure: IP66

2. Specifications
2.2. Certifications and approvals
Rev. 2 OWA 100 Adapter User Manual 5
July 2011
ATEX
DEKRA- Intrinsic Safety
II 1 G Ex ia IIB T4
II 1 D Ex tb IIIC T90°C, IP66
Ambient Temperature: –40°C ≤Ta ≤+70°C
Enclosure: IP66
DEKRA- Non Sparking
II 3 G Ex nA IIB T4
II 3 D Ex tb IIIC T90°C IP66
Ambient Temperature: –40°C ≤Ta ≤+85°C
Enclosure: IP66
For detailed OWA 100 Adapter specifications see the following Specification and Model Selection Guide.
OWA 100 Adapter (document 34-XY-03-43)
Provisioning Device
Install the Provisioning Device application on any PDA having
Windows Mobile version 4.2+
Infrared port.

2. Specifications
2.3. Agency compliance information
6 OWA 100 Adapter User Manual Rev. 2
July 2011
2.3 Agency compliance information
This section contains the Federal Communications Commission (FCC), Industry Canada (IC) and Radio
Frequency compliance statements for the OneWireless Multinode device.
ATTENTION
OWA 100 ADAPTER 100 units must be professionally installed in accordance
with the requirements specified in the OneWireless Agency Compliance
Professional Installation Guide.
FCC compliance statements
This device complies with Part 15 of FCC Rules and Regulations. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radiofrequency energy and, if not installed and used in accordance with these instructions, may
cause harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Intentional or unintentional changes or modifications must not be made to the Multinode unless under
the express consent of the party responsible for compliance. Any such modifications could void the
user’s authority to operate the equipment and will void the manufacturer’s warranty.
IC compliance statements
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropic radiated power (EIRP) is not more than that permitted for successful
communication.
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
This Class A digital apparatus complies with Canadian ICES-003.
French: Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Radio Frequency (RF) statement
To comply with FCC’s and Industry Canada’s RF exposure requirements, the following antenna
installation and device operating configurations must be satisfied.
This device must not be co-located with any other antenna or OWA 100 Adapter device and have a
separation distance of at least 20cm from all persons.
European Union Conformity
The OWA100 Wireless Transmitters are in conformity with the applicable portions of the ETSI standards
as required by the R&TTE Directive 1999/5/EC.

2. Specifications
2.4. Honeywell European (CE) Declaration of Conformity (DoC)
Rev. 2 OWA 100 Adapter User Manual 7
July 2011
2.4 Honeywell European (CE) Declaration of Conformity (DoC)
This section contains the European Declaration of Conformity (DoC) statement for the OWA 100 OneWireless
Adapter.

2. Specifications
2.4. Honeywell European (CE) Declaration of Conformity (DoC)
8 OWA 100 Adapter User Manual Rev. 2
July 2011

2. Specifications
2.5. IECEx Conditions of Certification:
Rev. 2 OWA 100 Adapter User Manual 9
July 2011
2.5 IECEx Conditions of Certification:
The enclosure is non-conducting and the area of the non-conducting part exceeds the maximum
permissible areas for Zone 0, Gb according to IEC 60079-0. Therefore when it is used within a
potentially explosive atmosphere, appropriate measures must be taken to prevent electrostatic
discharge.
2.6 ATEX Conditions for Safe Use:
The enclosure is non-conducting and the area of the non-conducting part exceeds the maximum
permissible areas for Category II 1 G (Zone 0) Gb according to EN 60079-0. Therefore when it is
used within a potentially explosive atmosphere, appropriate measures must be taken to prevent
electrostatic discharge.

3. Configuration
3.1. Safety Messages
10 OWA 100 Adapter User Manual Rev. 2
July 2011
3. Configuration
3.1 Safety Messages
These instruction procedures may require special precautions to ensure the safety of the personnel
performing the operations. Information that potentially raises safety issues is indicated by a warning
symbol ( ). Please refer to the following safety messages before performing an operation preceded by
this symbol.
Warnings
WARNING – POTENTIAL ELECTROSTATIC CHARGING HAZARD
The OWA 100 OneWireless Adaptor enclosure is non-conductive Lexan, EXL9330
Polycarbonate and may generate an ignition-capable level of electrostatic charge
under certain extreme conditions. The user should ensure that the equipment is
not installed in a location where it may be subjected to external conditions (such as
high-pressure steam), which might cause a build-up of electrostatic charge on non-
conducting surfaces.
WARNING
Failure to follow these instructions could result in death or serious injury.
• Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury.
The OneWireless Adapter can only be opened for battery insertion and
activation, or installed in a potentially hazardous location when the location is
declared to be non-hazardous.
• Before mounting the OneWireless Adapter to an existing field transmitter, verify
that the instruments are installed in accordance with applicable intrinsically safe
or nonincendive field wiring practices.
• Verify that the certification parameters of the OneWireless Adapter are
consistent with the appropriate hazardous locations certifications.
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions: This device may not cause harmful interference. This device
must accept any interference received, including interference that may cause
undesired operation.
This device must be installed to ensure a minimum antenna separation distance of
20 cm from all persons.