Honeywell Q7055A User manual

Honeywell BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
EN1B-0198GE51 R1004B
Q7055A
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
INSTALLATION INSTRUCTION & USER MANUAL
Quick Setup
In order to setup the BNA device properly,
the following connections are prerequisite:
•Null-Modem cable connected to a PC
running a VT100 terminal emulation
program or a VT100 compatible terminal
(refer to Table 6-1: Terminal settings)
•AN connection via UTP (RJ45 connec-
tor).
•Power connection.
•An active FTP-Server machine on the AN
The following BNA Bootloader commands
are mandatory for setting up the BNA (for a
detailed command description, refer to
chapter 6.5 Command Description on Page
31):
np Basic network parameters
dc Download configuration
load oad executable from FTP server
Before the application firmware is started it
is recommended to add some users (user
roles) using command um (refer to chapter
6.5.8 um - User management on Page 37)
After that, the BNA device can be installed
at its final operating location

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
EN1B-0198GE51 R1004B
Figure 1-1: Parts and Controls on the Front Side
Figure 1-2: Parts and Controls on the Rear Side
Technical Data
Supply Voltage 18-24 VAC (50 60 Hz);
18-24 VDC (external power
supply required)
Power Consumption 5VA (connected via 10BaseT,
twisted pair); 12VA
(connected via 10Base5)
Temperature Limits 0 +50 °C (+32 +122 °F);
5 95% rh, non condensing
Ambient storage limits: -35 +70 °C (-31 +160 °F);
5 95% rh, non condensing
System Data
Processor 25 MHz, MC68EN360, 32 Bit
Microprocessor (4 5MIPS)
Data Transfers 10Mbit/sec, 802 3 Ethernet
LAN-Interfaces 10BaseT (RJ45)
Field Bus (BNA-2DN) RS485 AC
coupled Manchester encoded
channels (L1-Bus compatible)
(BNA-2CS/1C) RS485 DC
coupled
Device Interface Serial RS232
Memory 4 MB SRAM, 2 MB Flash
MTBF >100 000 h
Weight 800 g (1 76 lb)
Dimensions (H x W x D) (76 x 158 x 200) mm
(2 99 x 6 2 x 7 87) in
Safety
Protection standard IP20 as per EN60529
Protection class II as per EN60730-1
Flame retardant V0 as per UL94
Agen y Listings
Electromagnetic compatibility (EMC) EN50081-1 and EN50082-2
Electromagnetic emission (EME) FCC Class A
Energy management UL916
Fire protection and smoke control UL864

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
EN1B-0198GE51 R1004B
Table of Contents
1 About BNA........................................................... 5
2 Lo ation of Parts and Controls.......................... 8
2 1 Front Side 8
2 2 Rear Side 11
3 Before Installation ............................................ 13
4 BNA Operating Positions ................................ 15
4 1 Single Device 15
4 2 Stacked Devices 16
4 3 Wall Mounting 16
5 Conne tions ....................................................... 19
5 1 Power Connection 19
5 2 Field Bus Connection (Ch1 / Ch2) 20
5 3 Bus Termination Switch 20
5 4 L1 Bus Termination 22
6 BNA Bootloader ................................................ 23
6 1 Startup Behavior 23
6 2 Operating Modes 25
6 3 Switching the Operating Mode 25
6 4 Device Setup 28
6 5 Command Description 31
6.5.1 Help or ?32
6.5.2 np - Basic network parameters 32
6.5.3 dc - Download configuration 33
6.5.4 load - Load executable 36
6.5.5 ping - ping 36
6.5.6 ver - Show installed software 37
6.5.7 run - Execute installed software 37
6.5.8 um - User management 37
6.5.9 whoami - Who am I 40
6.5.10 login - Login as different user 40

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
4 EN1B-0198GE51 R1004B
7 Cables and Conne tors..................................... 42
7 1 DB9F Null Modem Cable 42
7 2 Ethernet Connectors 44
7 2 1 RJ45 Connector 45
7 2 1 1 Connecting a BNA to a Hub 45
7 2 1 2 Connecting a BNA to a Workstation 46
Tips & Tri ks ............................................................ 48
FAQs........................................................................... 49
Glossary..................................................................... 50

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
EN1B-0198GE51 R1004B 5
1 About BNA
C
-
B
u
s
XCL5010
XCL5010
XCL5010
XCL5010
BNA-1C BNA-2CS BNA-2DN
S-Bus
F&S Bus
L1 Bus
Honeywell
XBS
TCP/IP LAN
The Building Network Adapter (BNA) delivers ex-
ceptional price/performance to meet the require-
ments of both building owners and service pro-
viders With its combination of scalable per-
formance, density, and low per-port pricing, the
Building Network Adapter allows network-layer
capabilities to be extended to a much wider range
of network configurations and environments
Customers can now gain the advantages of high-
performance network and services, including traffic
management to more locations throughout the
network
The Building Network Adapter uses the LAN-con-
nection to provide seamless communication to the

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
6 EN1B-0198GE51 R1004B
requesting device Status information like AN
communication activity, field bus traffic communication,
and system heartbeat of the Building Network
Adapter is indicated by LEDs on the front
Technically, the Building Network Adapter pro-
vides an interface from various Honeywell con-
troller busses that use RS232/RS485 signals to a
local area network using 802 3 Ethernet protocol
This allows data to be used by high-level building
management systems such as Enterprise Buildings
Integrator (EBI), Excel Building Supervisor (XBS),
and Excel Facility Integrator (XFI)
This Installation Instruction and User Manual covers
all of the BNA device types listed below
BNA-1C provides a single RS485 DC coupled C-
Bus-compatible communication chan-
nel for XL5000 family devices with up
to 76 8 kbps
BNA-2CS provides two RS485 DC coupled C- / S-
/ FS-90-Bus compatible communica-
tion channels for different applications,
like Excel IRC and Excel Classic as well
as XL5000 family devices with up to
76 8 kbps
BNA-2DN provides two RS485 AC coupled Man-
chester encoded L1-Bus (DeltaNet Peer
bus) compatible communication
channels

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
EN1B-0198GE51 R1004B 7
Additionally, each BNA type is equipped with a
RJ45 10Base T connector plus an RS232 interface

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
8 EN1B-0198GE51 R1004B
2 Location of Parts and Controls
The numbering for the parts and controls in this
section refers to the pictures on the rear side of the
title page In order to have a reference between the
numbering here and the device pictures, it is
possible to fold this page out
2.1 Front Side
Differences between the various BNA types are
explicitly noted in the corresponding element
description
1Reset
Hardware reset button Located directly behind
the small hole in the front panel To reach this
button, a pointed object like a sharp pen or an
unfolded paper clip is necessary Pressing this
button resets the BNA device immediately This
operation is similar to "power on" with the
BNA device
2Mode
Mode switch button This button is needed to
change the bootloader modes For a detailed
description about BNA operation modes, please
refer to chapter 6.2 Operating Modes on Page 25
3LAN
Local Area Network (LAN) activity display

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
EN1B-0198GE51 R1004B 9
Shows the actual LAN traffic using 4 LEDs
Col Collision indicator (Red) If this LED is
on, then two or more devices on the
network are transmitting at the same
time This is not a fault, but a normal
occurrence on an Ethernet network
However, when the Collision LED
remains on for all transmission attempts,
it may indicate an abnormal condition
such as an open end-of-line termination
Rx Receive indicator (Green) on means that
data is being received by the BNA over
the Ethernet
Tx Transmit indicator (Green) If this LED
is lit up, the BNA device is sending data
to the Ethernet When data is being
transmitted, the Rx indicator LED is lit
up simultaneously
Ln
k
Link indicator (Green) will always be lit
when the BNA is connected via the RJ45
connector to the Ethernet If this LED is
dark, it will not be possible to send or
receive any data
4Ch1
Bus Channel 1 activity display This display
contains two green LEDs, one showing BNA

BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN
10 EN1B-0198GE51 R1004B
reception activity (Rx) and the other showing
BNA transmission activity (Tx)
5Ch2
Bus Channel 2 activity display This display
contains two green LEDs, one showing BNA
reception activity (Rx) and the other showing
BNA transmission activity (Tx)
NOTE: Ch2 indi ation is available on two-
hannel devi es only. It is not available on a
BNA 1C devi e.
6Heartbeat
System heartbeat display During BNA system
runtime, this LED flashes continuously This
LED is a two-color LED A red flashing LED
means that the BNA bootloader is currently
active A green flashing LED means that an
application firmware is running
7Power
Power indicator This LED lights up when
power is connected to the BNA device