Honeywell Xenon XP 1950h User manual

Xenon™ XP 1950h
Corded Area-Imaging Scanner for Healthcare
Quick Start Guide
1950HC-EN-QS Rev B
4/19

1
Agency Model: 1950
Note: Refer to your User Guide for information about cleaning
your device.
Get Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.

2
Connect the Scanner
USB:

3
Keyboard Wedge:
RS232 Serial Port:

4
Reading Techniques
The view finder projects an aiming beam that
should be centered over the bar code, but it
can be positioned in any direction for a good
read.
Standard Product Defaults
The following bar code resets all standard product default set-
tings.
USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. If you are using a Microsoft®
Windows® PC, you will need to download a driver from the Hon-
eywell website (www.honeywellaidc.com). The driver will use the
next available COM Port number. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
Standard Product Defaults
USB Serial

5
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Epic
Scan the following bar code to configure your device to commu-
nicate with an Epic software application.
Meditech®
Scan the following bar code to configure your device to commu-
nicate with a Meditech software application.
USB PC Keyboard
EMR Application
Meditech Application

6
Quiet Operations
The following codes configure the scanner for quiet modes that
do not disturb resting patients.
Silent Mode with Flashing LED
Scan the following bar code to completely silence the scanner.
When a bar code is scanned, the LED and aimer flash 5 times.
Green indicates a good scan, red indicates a bad scan.
Silent Mode with Long LED
Scan the following bar code to completely silence the scanner.
When a bar code is scanned, the LED and aimer remain solidly
lit for 1 second. Green indicates a good scan, red indicates a bad
scan.
Silent Mode with Flashing LED
Silent Mode with Long LED

7
Very Low Beeper (Nighttime Mode)
The following bar code programs the scanner for a very low
beep. When a bar code is scanned, the scanner emits a very soft
beep.
Low Beeper (Daytime Mode)
The following bar code programs the scanner for a low volume.
When a bar code is scanned, the scanner emits a low beep.
Trigger
The following bar codes will allow you to use the scanner in
Manual Trigger - Normal Mode (need to press the trigger to
read) or Presentation mode (the scanner is activated when it
“sees” a bar code).
Nighttime Mode
Daytime Mode
Manual Trigger - Normal
(Default)
Presentation Mode

8
Streaming Presentation™
When in Streaming Presentation mode, the scanner leaves the
scan illumination on all the time and continuously searches for
bar codes.
Suffix
If you want a carriage return after the bar code, scan the Add CR
Suffix bar code. To add a tab after the bar code, scan the Add
Tab Suffix bar code. Otherwise, scan the Remove Suffix bar
code to remove the suffixes.
Streaming Presentation Mode
Add CR Suffix
Add Tab Suffix
Remove Suffix

9
Add Code ID Prefix to all Symbologies
Scan the following bar code if you wish to add a Code ID prefix to
all symbologies at once.
Note: For a complete list of Code IDs, see the User Guide for your
product.
Keyboard Country
Scan the appropriate country code below to program the key-
board layout for your country or language. By default, national
character replacements are used for the following characters:
#$@[\]^‘{|}~ Refer to the ISO 646 Character Replacements chart
in your User Guide to view the character replacements for each
country.
Add Code ID Prefix To All Symbologies
(Temporary)
USA (Default)
Belgium
Denmark
Finland