Honeywell Hyperion 1300G User manual

SPO –Systems support
Honeywell Hyperion 1300G
Scanner User Guide
SPO-NA-EN-373, V1.0

© IZUM, 2019
IZUM, COBISS, COMARC, COBIB, COLIB, CONOR, SICRIS, E-CRIS are registered
trademarks owned by IZUM.

© IZUM, 19. 3. 2019, SPO-NA-EN-373, V1.0 i
CONTENTS
1Using the Honeywell Hyperion 1300G scanner.................................................. 1
1.1 Connecting the scanner with USB ...................................................................................1
1.2 Barcode reading techniques .............................................................................................1
1.3 Factory default settings....................................................................................................2
1.4 Troubleshooting ...............................................................................................................2
2Honeywell Hyperion 1300G scanner settings..................................................... 3
2.1 Basic settings....................................................................................................................3
2.2 Settings for Interleaved 2 of 5..........................................................................................4
2.3 Beeper volume settings....................................................................................................5
2.4 Testing the setup parameters and scanning barcodes.......................................................6
Figures
Figure 1: Correct and incorrect scanning........................................................................................1
Figure 2: Factory default settings....................................................................................................2

SPO Honeywell Hyperion 1300G Scanner User Guide
© IZUM, 19. 3. 2019, SPO-NA-EN-373, V1.0 1/6
1Using the Honeywell Hyperion 1300G scanner
1.1 Connecting the scanner with USB
Connect one end of the interface cable to the scanner (1), and the
other end to the USB port of your personal computer (2). The scanner
emulates the operation of a keyboard.
Replacing the USB cable:
If the USB cable needs replacing, insert a straightened paperclip through the
small hole on the side of the scanner's handle to release the connector.
1.2 Barcode reading techniques
The scanner has a bright red aiming beam. The aiming beam should be centred horizontally over
the bar code.
Figure 1: Correct and incorrect scanning
1
2
Correct
Incorrect
Incorrect

Honeywell Hyperion 1300G Scanner User Guide SPO
2/6 © IZUM, 19. 3. 2019, SPO-NA-EN-373, V1.0
1.3 Factory default settings
To reset the scanner to the factory default settings, scan the barcode below.
Figure 2: Factory default settings
By doing so, the settings that are crucial for the use within the COBISS system are changed and
set to the values below:
Parameter
Setting/parameter value
Keyboard
USA*
Scanning sound
On
Scanning beeper pitch
Medium (2700 Hz)
LED-indicator
On
Trigger mode
Manual
Adding CR after scanning
On
CODABAR
On
CODABAR –Start/Stop character
Do not transmit
Code 39
On
Interleaved 2 of 5
On
CODE 93
On
CODE 128
On
EAN 13
On
*Change to Slovenian.
If necessary, these parameters may be updated (see chapter 2).
1.4 Troubleshooting
The scanner automatically performs a self-test when you turn it on. If your scanner is not
working properly, check the following:
1. Is the power on?
2. Does the red aiming beam illuminate when you press the trigger?
If the aiming beam does not illuminate:
1. Is the cable connected properly on both ends (scanner, computer)?

SPO Honeywell Hyperion 1300G Scanner User Guide
© IZUM, 19. 3. 2019, SPO-NA-EN-373, V1.0 3/6
2. Is the computer on and is it powering the scanner?
3. Is the trigger working?
If the scanner is having trouble reading barcodes:
1. Are the barcodes smeared, scratched or dirty?
2. Is the scanner dirty of are there water droplets on its surface?
If the scanner scans the barcode, but you still have to press a key to enter it:
1. You need to program a suffix for the scanner (Enter/Return).
If the scanner won't read the barcode at all:
1. Scan the sample barcode. If the scanner reads the sample barcode, check that your barcode
is readable.
2. If the scanner can't read the sample barcode, enable the scanning of this barcode type.
If you are unsure about the current scanner settings, reset it to the factory default settings and
then reset the required settings.
2Honeywell Hyperion 1300G scanner settings
Set up the scanner by connecting the scanner and reading the barcodes in the right column of the
table below (from top to bottom). Each step is explained next to each barcode (on the left).
2.1 Basic settings
1
Before setup, return the scanner to
EU factory settings →
2
Set the Keyboard Country Layout
to:
Slovenia
→
3
Set up on stand –automatic trigger*
Presentation Mode →

Honeywell Hyperion 1300G Scanner User Guide SPO
4/6 © IZUM, 19. 3. 2019, SPO-NA-EN-373, V1.0
3*
Manual scanning (turn off automatic
trigger) Manual Trigger →
2.2 Settings for Interleaved 2 of 5
1
To enable Interleaved 2 of 5:
I 2 of 5 = On →
2a
Barcode length parity –even:
validates and transmits check
character:
Validate and Transmit→
2b
Barcode length parity –odd:
validates but doesn't transmit check
character:
Validate, but don't Transmit →
When setting up the Interleaved 2 of 5 barcode, perform step one, followed by either 2a or 2b.
Perform step 2a for Interleaved 2 of 5 barcodes with even parity.
Perform step 2b for Interleaved 2 of 5 barcodes with odd parity.

SPO Honeywell Hyperion 1300G Scanner User Guide
© IZUM, 19. 3. 2019, SPO-NA-EN-373, V1.0 5/6
2.3 Beeper volume settings
Select the beeper volume: 1a, 1b, 1c or 1d.
1a
Beeper volume –good read:
Low
→
1b
Beeper volume –good read:
Medium
→
1c
Beeper volume –good read:
High
→
1d
Beeper volume –good read:
Off
→

Honeywell Hyperion 1300G Scanner User Guide SPO
6/6 © IZUM, 19. 3. 2019, SPO-NA-EN-373, V1.0
2.4 Testing the setup parameters and scanning barcodes
Check if the parameter setup was successful with the test barcodes below.
COBISS
Additional barcodes
CODE 93
Brez kontrolnega znaka (4)!