Honeywell GSMX-AUDIO User manual

GSMX-AUDIO and GSMV-AUDIO, Audio Cable Routing Instructions
For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/
Routing Instructions for the GSMX-AUDIO cable.
1. At the GSMX, loosen the captive cover screw and swing the
cover open. Open the enclosure where the AVS Base Unit
resides.
2. Ensure power is removed by disconnecting the GSMX’s ECP
cable, and powering down the control and AVS Base Unit.
3. Connect the 5-pin end of the audio cable to the audio
connector on the GSMX circuit board.
4. Route the audio cable to the connector on the AVS Base
Unit.
5. Connect the 4-pin end of the audio cable to the
connector on the AVS Base Unit.
6. Ensure the audio cable ends are secured with tie
wraps to reduce strain.
7. At the GSMX, connect the ECP cable. Close the cover
and tighten the captive screw.
8. At the AVS Base Unit, close the enclosure.
9. Power up the system, and test.
AUDCBL-001-V0
AVS BASE UNIT
2341
ON
52341
ON
AUDIO
CONNECTOR
5-pin connector
4-pin connector

Routing Instructions for the GSMV-AUDIO cable
1. At the GSMV, remove the cover screw if present. Using a
medium blade screwdriver, release the communicator’s
cover by depressing the two locking tabs at the bottom of
the unit.
2. Ensure power is removed by disconnecting the battery
cables, and remove the source of power supplying TB1
pins 1, 2 and 3. Depending on the system, this may be a
transformer or other source.
3. Power down the control and AVS Base Unit.
4. At the GSMV, remove two [2] screws and standoff that
secure the small PC board, and swing up.
5. Connect one end of the audio cable to the audio connector
located on the small PC board.
6. Secure the small PC board and plastic standoff with two
[2] screws. Note the standoff mounts on the right side.
7. Route the audio cable to the connector on the AVS Base
Unit and connect the cable.
8. Ensure the audio cable ends are secured with tie wraps to
reduce strain.
9. Power up the source of power supplying TB1 pins 1, 2
and 3. Depending on the system, this may be a trans-
former or other source. Attach the battery cables.
10. Power up the control and AVS Base Unit.
11. Close all enclosure covers (not shown) and secure with
screw as necessary. Test the system.
FOR EXTERNAL ANTENNA
50 OHM, MMCX ONLY
7720P PROGRAMMER PORT
NOT FOR TELEPHONE SERVICE USE!
PRIMARY POWER:9-1 .5VAC
BATTERY: V. 3.1 AHr FOR 24 Hr BACKUP
FCC ID: GIPMC5 IC: Y2 7W - MC5
GSM
GPPS
WEB
MODE2
MODE1
RSSI
Honeywell
RX
TX
MAC LABEL HERE
TRANSMIT LED
AUDCBL-002-V0
FOR EXTERNAL ANTENNA
50 OHM, MMCX ONLY
7720P PROGRAMMER PORT
NOT FOR TELEPHONE SERVICE USE!
PRIMARY POWER:9-1 .5VAC
BATTERY: V. 3.1 AHr FOR 24 Hr BACKUP
FCC ID: GIPMC5 IC: Y2 7W - MC5
GSM
GPPS
WEB
MODE 2
MODE 1
RSSI
Honeywell
RX
TX
MAC LABEL HERE
TRANSMIT LED
AUDCBL-003-V0
TB 1
6
7
8
5
11
10
9
2
3
4
1
FOR EXTERNAL ANTENNA
50 OHM, MMCX ONLY
7720P PROGRAMMER PORT
NOT FOR TELEPHONE SERVICE USE!
PRIMARY POWER: 9 - 16.5 VAC
BATTERY: 6V. 3.1 AHr FOR 24 Hr BACKUP
FCC ID: GIPMC56 IC: Y267W - MC56
GSM GPPS WEB MODE 2 MODE 1 RSSI
Honeywell
RX
TX
MAC LABEL HERE
TRANSMIT LED
AVS BASE UNIT
2341
ON
52341
ON
WARRANTY For the latest warranty information go to: http://www.security.honeywell.com/hsc/resources/wa/
Ê800-06409FŠ
800-06409 4/10 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2010 Honeywell International Inc.
www.honeywell.com/security