Honeywell HHC12 Series User manual

Install Guide
HHC12 Series
Document 800-04354 – 04/09 – Rev A
12-Inch Camera
Enclosure

Rev A 2 Document 800-04354
04/09
Revisions
Revision Date Revisions
A 04/09 New document updated to Honeywell standards, based on
900.0559

Rev A 3 Document 800-04354
04/09
Warnings
Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
WARNING! The use of CSA Certified/UL Listed Class 2
power adapters is required to ensure
compliance with electrical safety standards.
Explanation of Graphical Symbols
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
CAUTION

Rev A 4 Document 800-04354
04/09

Rev A 5 Document 800-04354
04/09
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting the Heater/Blower (HHC12WM2 Model Only) . . . . . . .9
Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Mounting the Wall Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Rev A 6 Document 800-04354
04/09

Rev A 7 Document 800-04354
04/09
Introduction
The HHC12 Series camera housings are stylishly and functionally designed for 1/2"
and 1/3" CCD cameras with fixed focal length or small zoom lenses.
Features
Ordering Information
• Contemporary design • Die-cast and extruded aluminum
construction
• Adjustable mounting rack • Removeable body for easy servicing
• Indoor/outdoor applications • Epoxy powder coating for corrosion
resistance
• IP66 rated
Model No. Description
Housing Models
HHC12WM 12-inch housing with sunshield and HHMW13 wall mount
HHC12WM2 12-inch housing with sunshield, heater kit, blower kit and HHMW13
wall mount
Optional Components
HHMC21J Ceiling “J” mount, 21” high, 30 lbs (13.5 kg) max.
HHMCMA Corner mount adapter for HHMW13
HHMPMA Pole mount adapter for HHMW13
HHMW13 Wall mount, 13” high, 30 lbs (13.5 kg) maximum, gray

Rev A 8 Document 800-04354
04/09
Before You Begin
Unpack Everything
Check that the items received match those listed on the order form and packing slip.
The HHC12 packing box includes, in addition to this guide:
If any parts are missing or damaged, contact the dealer you purchased the housing
from or call Honeywell Customer Service (see back cover).
Equipment Required
You may require the following tools (not supplied) to complete the installation:
Screwdriver, camera and camera cable, power supply
Housing Model Packing Includes
HHC12WM • One 12-inch housing with sunshield
• One desiccant bag
• One HHMW13 wall mount
• Four 1/4 x 20 UNC machine screws
• Four #14 1-1/4 sheet metal screws
HHC12WM2 • One 12-inch housing with heater, blower and sunshield
• One desiccant bag
• One HHMW13 wall mount
• Four 1/4 x 20 UNC machine screws
• Four #14 1-1/4 sheet metal screws
This guide describes how to assemble the housing and its
optional components, affix the camera, and mount the assembly
to a suitable surface. Please carefully read this guide before you
install the housing.
Keep this guide for future reference.

Rev A 9 Document 800-04354
04/09
Installation
To correctly install the heater/blower and mount the camera, please follow the
instructions in the order provided.
Preparing for Installation
1. Loosen but do not remove the screw that secures the sunshield in place. Turn the
screw no more than 5 times.
2. Detach the sunshield by sliding it backward on the main housing unit. Set the
sunshield aside until needed.

Rev A 10 Document 800-04354
04/09
3. Unlatch the lid and open the upper body.
4. Remove the desiccant bag from the protective packaging and place the bag
inside the housing to absorb moisture.
5. Close the housing.
6. Locate the gold, 1/4” x 20 panhead UNC screws and set them aside for use later.
Connecting the Heater/Blower (HHC12WM2
Model Only)
Feed the external power supply (not included) through one of the compression
glands, then connect to the circuit board. The recommended power supply is 24 VAC,
50VA.
J1
AC
R1
GND
C1
GND AC OUT
FAN
GND HEATER
Ground
AC/Out
VDC
to Blower
B
Ground
VAC Out
AC/IN
Ground
to Heater
to camera
Compression glands
Caution These wires must be connected for
the heater/blower/camera to operate.
from external 24 VAC
power supply

Rev A 11 Document 800-04354
04/09
Mounting the Camera
This section describes how to install a camera into any of the HHC12 Series camera
housings.
1. Remove the mounting plate from the lower body by unscrewing one Philips
panhead screw. Set the screw aside.
2. Tilt the mounting plate as shown.
3. Mount the camera onto the mounting plate and secure with the 1/2” Philips
panhead screw. You may need to turn the mounting plate over to better
accommodate your camera.
4. Place the mounting plate in its original position and secure the assembly by
tightening the Philips panhead screw through the mounting plate into the lower
body of the housing.
5. Run the camera cable through the compression glands and make all necessary
electrical connections (refer to the guide that came with your camera). Ensure
that the compression glands are firmly fixed.
1. Unscrew the panhead
screw.
2. Tilt the mounting plate.
3. Secure the camera with a
1/4 x 20 UNC screw.
5. Run the camera cable
through the
compression glands.
4. Return the mounting
plate to the original
position.

Rev A 12 Document 800-04354
04/09
6. Reassemble the housing unit by closing the upper body and latching the lid tight.
7. If applicable, reinstall the sunshield by sliding it across the top of the housing.
Mounting the Wall Bracket
To mount the wall bracket:
1. Use fasteners of an appropriate size and type to attach the bracket to the wall
surface. Position the housing so that it allows for viewing the selected area.
2. Locate the two nuts that freely slide along the channel. Position the nuts
approximately 2 inches from each other.
3. Place the housing onto the mount, aligning the holes. Insert the two 1/4"-20 UNC
screws (supplied) through the mount and into the nuts and tighten to secure the
assembly.
4. Adjust the moveable arm of the wall bracket to attain the desired position.
5. Tighten the bolt located at the pivot point of the moveable arm and tighten the set
screw.
6. Latch the lid.
2. Position the
two nuts 2”
apart.
3. Secure the housing with
2 x 1/4 x 20 UNC screws.
4. Adjust the arm,
then tighten the
set screws.
1. Attach the
bracket to the
wall using 4
sheet metal
screws.

Rev A 13 Document 800-04354
04/09
Maintenance
Regularly scheduled maintenance prolongs the operational life and appearance of
equipment.
On a regular basis, do the following:
• Maintain picture quality by cleaning the viewing area window with a soft cloth and
a mixture of mild detergent and water.
• Verify that all mounting hardware is secure.

Rev A 14 Document 800-04354
04/09
Specifications
Housing Specifications
Dimensions:
(with sunshield)
6.0 x 4.6 x 15.9 in
(153 x 118 x 406 mm)
Weight:
HHC12WM2 6.2 lbs (2.8 kg) (without mount)
Max. camera size:
HHC12WM
HHC12WM2
Accommodates camera/lens combinations (including
BNC) up to:
3.1 x 3.2 x 11.4 in (78 x 82 x 290 mm)
3.1 x 3.2 x 9.0 in (78 x 82 x 230 mm)
Viewing area: 2.9 x 2.4 in (73 x 61 mm)
Viewing window: Clear 1/8”double-density glass
Construction: Extruded and die-cast aluminum
Finish: Epoxy powder coating
Environment: Indoor/outdoor: -4°F to 140°F (-20°C to 60°C)
IP66 rated
Camera mounting: Slotted camera sled
Recommended mounts: HHMC21J (Ceiling “J” mount)
HHMW13 (Wall mount)
HHMCMA (Corner mount adapter)
HHMPMA (Pole mount adapter)
Cable entry: 3 compression fittings: PG9, PG16, PG21
Sunshield Specifications
Dimensions:
(sunshield only)
5.9 x 2.3 x 15.9 in
(150 x 60 x 406 mm)
Weight: 1.32 lbs (0.6 kg)

Rev A 15 Document 800-04354
04/09
Heater (HHC12WM2) Specifications
Power Supply: 24 VAC
Power Consumption: 20 W
Heater ON: Heater turns ON at 41°F (5°C)
Heater OFF: Heater turns OFF at 59°F (15°C)
Blower (HHC12WM2) Specifications
Power Supply: 24 VAC
Power Consumption: 3.4 W
Blower ON: Blower turns ON at 95°F (35°C)
Blower OFF: Blower turns OFF at 68°F (20°C)

Video Systems
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
© 2009 Honeywell International Inc. All rights reserved. No part of this publication may be
reproduced by any means without written permission from Honeywell Video Systems. The
information in this publication is believed to be accurate in all respects. However, Honeywell Video
Systems cannot assume responsibility for any consequences resulting from the use thereof. The
information contained herein is subject to change without notice. Revisions or new editions to this
publication may be issued to incorporate such changes.
Honeywell Systems Group (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
℡+1.800.796.2288
Honeywell Systems Group Europe/South
Africa
Aston Fields Road, Whitehouse Industrial Estate
Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
℡+44.01928.754028
Honeywell Systems Group Pacific
Unit 5, Riverside Center, 24-28 River Road West
Parramatta, NSW 2150, Australia
www.honeywellsecurity.com.au
℡+61.2.8837.9300
Honeywell Systems Group Asia
35F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
℡+86 21.5257.4568
Honeywell Systems Group Middle East/N.
Africa
Post Office Box 18530
LOB Building 08, Office 199
Jebel Ali, Dubai, United Arab Emirates
www.honeywell.com/security/me
℡+971.04.881.5506
Honeywell Systems Group Northern Europe
Ampèrestraat 41
1446 TR Purmerend, The Netherlands
www.honeywell.com/security/nl
℡+31.299.410.200
Honeywell Systems Group Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.honeywell.com/security/de
℡+49.74 31.8 01.0
Honeywell Systems Group France
Immeuble Lavoisier
Parc de Haute Technologie
3-7 rue Georges Besse
92160 Antony, France
www.honeywell.com/security/fr
℡+33.(0).1.40.96.20.50
Honeywell Systems Group Italia SpA
Via della Resistenza 53/59
20090 Buccinasco
Milan, Italy
www.honeywell.com/security/it
℡+39.02.4888.051
Honeywell Systems Group España
Mijancas 1. 3a planta
P.Ind. Las Mercedes
28022 Madrid, Spain
www.honeywell.com/security/es
℡+34.902.667.800
Document 800-04354 Rev A 04/09