Honeywell Silent Knight 6820EVS Technical specifications

Cut Along the Dotted Line
P/N: LS10161-001SK-E Rev A
ECN: 16-0218
6820EVS Basic Operating Instructions
These instructions must be framed and displayed next to the 6820EVS panel in accordance with
NFPA 72 fire code for Local Protected Fire Alarm Systems
FS= Fire System EVS = Emergency Voice System
Operation Task to Perform
Silence Alarms and
Troubles Press SILENCE then enter a code if prompted. Silence LED will light.
Reset Alarms
1. Press RESET.
2. Press 1 to Reset Fire System.
3. Press 2 to Reset Emergency System.
Note: To reset EVS at an LOC, the user must gain EVS Control. (See Figure 1).
View all active alarms,
troubles, and
supervisories signals
The highest priority event will display first. Press the Down arrow to view location and type of alarm or
trouble.
View a Point’s Status
1. Press ENTER to access Main Menu.
2. Press 2 to select Point Functions.
3. Then press 2 to select Point Status.
4. Select the module the device is located on by using the Up or Down button. Then press ENTER.
5. Enter the point number.
Conduct a Fire Drill
1. Press ENTER to access Main Menu.
2. Then Press 1 to select System Tests.
3. Press 1 to select Fire Drill.
4. Press ENTER to start the fire drill.
5. Press ENTER to end the fire drill.
Set Time and Date
1. Press ENTER to access Main Menu.
2. Then press 4 to select Set Time & Date. Enter a code if prompted
3. Make changes in the fields on the screen as necessary.
4. Press ENTER if you wish to keep the changes.
5. Press ENTER to set the entered time and date.
Enable / Disable a Point
1. Rotate the key or enter a code to access to access Main Menu.
2. Press 2 to select Point Functions.
3. Press 1 for Disable / Enable Pt
4. Press 7 for Disable / Enable Pt.
5. Use the Up or Down button to move through the list. Then press ENTER to select the module where
the point you want to disable/enable is located
6. Enter the point or circuit number that you want to disable/enable.
7. Press the right arrow key to toggle between NORMAL (enable) or DISABLE.
To Gain / Request EVS
Control
1. Press the Button and follow the on-screen Instructions.
Note: WhenEVSControlLEDisblinking, another LOChasEVS Control. EVSControlLEDis onsteady
when the LOC has EVS Control.
For Service Call:

Cut Along the Dotted Line
P/N: LS10161-001SK-E Rev A
ECN: 16-0218
Integrated Voice Operation
Table 1: LED Conditions
LED Color States Meaning
Select Keys
Red On The corresponding area is active for the currently playing EVS
message.
Off The corresponding area is not active.
Green On The corresponding area is active for the microphone.
Off The corresponding area is not active for the microphone.
EVS Control LED Green
On LOC has EVS Control and the user is able to make changes to
the EVS.
Off LOC does not have EVS Control.
Blinking Another LOC has EVS Control
EVS Message LED
Red On The corresponding EVS event was activated by an EVS device.
Off The corresponding EVS event is not active.
Green On The corresponding EVS event is active and was generated from
the LOC (or was activated from another LOC, but this LOC now
has EVS Control).
Off The corresponding EVS event was not activated from this LOC or
this LOC does not have EVS Control.
ALL CALL
Key
NON-ACTIVE CALL
Button EVS Control
Key
EVS Status LED
Message (1-8)
Select
Message
LEDS
Activate Keys
Keys
Select
LED’s
Ready to
Talk LED

Cut Along the Dotted Line
P/N: LS10161-001SK-E Rev A
ECN: 16-0218
How to Operate the Microphone:
1. Press the EVS Control button
2. Key the Microphone
3. Press the All Call button
How to Reset the EVS System
1. Press the Reset button
2. Select 2 to Reset emergency system
EVS-LOC Operating Instruction
For Live Message
1. Key the Microphone.
2. Press the All Call Key or select desired output area using select keys.
3. Deliver your verbal message.
For Pre-recorded Message
1. Select desired EVS Message Key 1-8.
• If EVS Control LED is on steady, the LOC has EVS Control.
• If EVS Control LED is Blinking, another LOC has EVS Control.
Table 2: EVS Control Request
Operation Task
Gain EVS Control at an LOC
Press the EVS Control Key and enter a code if prompted. If EVS Control is
available, the EVS Control LED will illuminate. If another LOC has EVS
Control, the display will be similar to the one shown. Press 1 to request control.
The LOC with EVS Control will then be able to allow or deny the request.
Gain EVS Control as EVS Super
User at an LOC (only one EVS
Super User is allowed EVS Control
in the system at a time).
From the idle screen, enter an EVS Super User access code and then press
the EVS Control Key. If EVS Control as Super User is available, the EVS
Control LED will illuminate. If another LOC has Super User EVS Control, a
request for Super User EVS Control will automatically be made to the LOC
with control. The LOC with Super User EVS Control will then be able to allow
or deny the request. (See Figure 1-2 for screen display example).
Select all output group for
microphone override Key the microphone, press the All Call Key, wait for the Ready-to-Talk LED to light, and then deliver your verbal message.
Select all non-activated output
groups for microphone override Key the microphone, press the Non-Active Call Key, wait for the Ready-to-Talk LED to light, and then deliver your verbal message.