Honeywell NOTIFIER IDR-M Guide

IDR-M mimic installation
and
commissioning
manual
997-412-000-3, Issue 3 June 2005

IDR-M Mimic Installation & Commissioning Manual
Contents
i 997-412-000-3, Issue 3
June 2005
Quick Contents Reference by
Section

IDR-M Mimic Installation & Commissioning Manual
Contents
ii997-412-000-3, Issue 3
June 2005
Contents
1 Introduction 1
1.1 CE Marking 1
1.2 System Design and Planning 2
1.3 General 2
1.4 Related Documents 2
1.5 Warnings and Cautions 3
1.6 Tips 3
2 Installation Guide 4
2.1 Pre-Installation Check List 4
2.1.1 Some DO’s and DON’T’s 4
2.2 Transient Protection 5
2.3 Installation 6
2.3.1 Checking Your Equipment for Damage 6
2.3.2 What To Do if Your Equipment is
Damaged or Suspect 7
2.4 Mimic Display Components 8
2.4.1 Typical Configuration - LEDs and I/O 9
2.4.2 Typical Configuration - Relays 10
2.5 Installation Procedure 11
2.5.1 IDR-M Control Board Kit 11
2.5.2 IDR-MD Mimic Driver Kit 14
2.5.3 LEDSelection 16
2.5.4 Relay Selection 16
3 Commissioning 17
3.1 Preliminary Checks 17
3.2 Powering the IDR-M Mimic 17
3.3 IDR Configuration Tool 17
Appendix 1 - Specification A1-1
Appendix 2 - Calculating Battery
Requirements A2-1

IDR-M Mimic Installation & Commissioning Manual
Introduction
1 997-412-000-3, Issue 3
June 2005
1 Introduction
This manual provides the user with all
recommendedproceduraldescriptionsandfull
technicaldetails for thesuccessfulinstallation,
commissioning,configuration and operationof
an IDR-M mimic.
Procedures described in this manual include
appropriatewarnings andcautions toguidethe
user towards adopting safe and methodical
work practices during the installation and
commissioning phases.
Important Note
This manual must be read, and its content
clearly understood, before proceeding with
any work relating to the IDR-M mimic.
Damage to the mimic display and/or the fire
control panel(s) may result from NOT
following the recommended procedures
described in this manual.
If there are any areas of doubt, consult your
supplier before continuing with the system
installation, commissioning or configuration.
1.1 CE Marking
The IDR-M mimic is CE Marked to show that
itconforms to therequirementsofthe following
European Community Directives:
ElectromagneticCompatibilityDirective89/
336/EEC(and the amending Directives
92/31/EEC and 93/68/EEC).

IDR-M Mimic Installation & Commissioning Manual
Introduction
2997-412-000-3, Issue 3
June 2005
1.2 System Design and Planning
It is assumed that the system, of which the
IDR-M mimic is a part, has been designed by
a competent fire alarm system designer in
accordance with the requirements of EN54
Part 14 and any other local codes of practice
that are applicable.
1.3 General
The IDR-M mimic can be used with the following
firecontrolpanels:
a. ID2000 Series.
b. ID3000 Series.
c. ID50.
TheIDR-M mimiccan haveup toeight IDR-MD
Driver boards. Each Driver board has:
a. 64outputchannels, arranged in two banks
of 32. Each bank has four groups of eight
outputs, and each group can drive either
LEDs or relays, dependant upon a jumper
linkselectionontheboard. The groupsare
configuredindependently(i.e. on the same
bankand/or board, some groupsmay drive
LEDs and others relays). Outputs within a
groupcannotbe configured independently.
b. 8I/O lines.Thesecanbeconfiguredtodrive
additional relays or to read switches (first
board only), depending upon the
configuration method used during
commissioning (see below).
Installation
TheIDR-Mmimic is easy to installproviding the
recommended procedures described in this
manual are followed. To avoid inadvertent
contaminationofthemimicPCBassemblies,the
manufacturer recommends they be installed in
the enclosure only after all other trades have
completed their tasks.
Commissioning
To commission the IDR-M mimic, follow the
recommended procedures described in this
manual. The IDR-M mimic can be configured
by one of two methods:
a. Setting hardware switches to relate the
mimicdisplaysto zonal events.In this case
the IDR-M mimic can only indicate the
statusof onestand-alone fire control panel.
b. Use of the IDR Configuration Tool to set
software rules which relate the mimic
displays to zonal or non-zonal events.The
Toolprovidesa higherlevel offlexibility than
thatavailable using thehardwareswitches.
Only fit the mimic display
PCB assemblies after all
the other trades have
completed their tasks!

IDR-M Mimic Installation & Commissioning Manual
Introduction
3 997-412-000-3, Issue 3
June 2005
1.4 Related Documents
This manual only describes the IDR-M mimic.
Refer to the documentation supplied with the
fire control panel for information about that
panel.Informationabout theIDRConfiguration
Tool is given in a soft-copy manual supplied
with the Tool.
1.5 Warnings and Cautions
Where appropriate, this manual includes
advisorywarningsandcautionsto remind you
toconsidersafety at all times,especiallywhen
following the procedures given herein (see
example to the left of this paragraph).
You are alerted to any areas where there may
beariskof damage to static-sensitivedevices
if the recommended procedures described in
this manual are not followed.
Anexample ofan anti-staticcautionisprovided
to the left of this paragraph.
1.6 Tips
‘Handy tips’ are included, where appropriate,
to assist you in following quick and safe
procedures for system installation and
integration. Look for the ‘TIP!’ icon and
supporting text, typically illustrated at left.
Static Sensitive Devices!
Use anti-static wrist strap
when carrying out these
procedures
To avoid damage to the
IDR-M mimic and to the fire
control panel ensure that
you follow these
instructions
0V for inputs and
28V for outputs are
available at J5

IDR-M Mimic Installation & Commissioning Manual
Installation Guide
4997-412-000-3, Issue 3
June 2005
2 Installation Guide
This Installation Guide is intended to provide
youwithsimpleguidelines on how to install an
IDR-M mimic quickly and safely.
Foreachstage in the IDR-Mmimicinstallation
and commissioning procedures a brief
description is given of its purpose, complete
with detail drawings and/or other graphics to
make the instructions easy to follow.
2.1 Pre-Installation Check List
Before installing the IDR-M mimic you must
firstensure thatthe followingcriteria havebeen
met. Failure to do this may not only result in
damagetothe equipment, but mayalsocause
problemswhencommissioning the equipment
or adversely affect its performance.
2.1.1 Some DO’s and DON’T’s
Before selecting a location for the IDR-M
mimic, DO make sure that:
a. Theoperating ambienttemperature isin the
recommended range:
+5°C to +35°Cand
b. The relative humidity is between:
5% and 95%
c. The IDR-M mimic is wall mounted in a
position which allows clear visibility of any
configured displays. The height above floor
levelshouldbechosensuchthatthedisplays
can be easily viewed.
95%
Max.
5%
Min.
+35 C
o
+5 C
o

IDR-M Mimic Installation & Commissioning Manual
Installation Guide
5 997-412-000-3, Issue 3
June 2005
d. DO NOT locate the IDR-M mimic where it
is exposed to high levels of moisture.
e. DO NOT locate the IDR-M mimic where
there are high levels of vibration or shock.
f. DO NOT sitetheIDR-Mmimic where there
would be restricted access to the internal
equipmentandcabling/wiring connections.
2.2 Transient Protection
This equipment contains transient-protection
devices. Although no system is completely
immune from lightning transients and
interference, for these devices to function
correctly, and to reduce susceptibility, this
equipment must be earthed correctly.
Aswith all solid statedevices,thissystem may
operate erratically or can be damaged if
subjected to lightning-induced transients.
Theuseofoverhead or outside aerial wiringis
not recommended due to the increased
susceptibility to nearby lightning strikes.

IDR-M Mimic Installation & Commissioning Manual
Installation Guide
6997-412-000-3, Issue 3
June 2005
2.3 Installation
The IDR-M mimic is relatively simple to install
provided the recommended procedures
described in this Installation Guide are
followed.
Follow all installation instructions
described in this manual. These
instructions must be understood and the
manufacturer’s recommendations followed
to avoid damage to the IDR-M mimic and
to the fire control panel and associated
equipment.
2.3.1 Checking Your Equipment for
Damage
It is important to check all supplied
equipment for damage before proceeding
with the installation!
Beforeattemptingto install yourIDR-Mmimic,
you should do the following:
1After removing each component
(dependent upon your configuration) from
itspackaging,andbefore you proceed with
the installation, check for any damage that
may have been caused while in transit.
Note: In the unlikely event that the any of the
components of the IDR-M mimic have
been damaged, you MUST NOT install
it but return it to your supplier. The
procedure for returning faulty items is
described in Section 2.3.2, What to do
if Your Equipment is Damaged or
Suspect.
2If you are satisfied that none of the
componentsof theIDR-Mmimic havebeen
damaged you can now commence the
installation procedure. This manual
addresses the recommended installation
methods for the IDR-M mimic. Refer to the
relevant sections that apply to your
configuration requirements.
To prevent unnecessary damage to the
electronic components, the IDR-M mimic
PCBsshouldonlybeinstalledinanenclosure
AFTER that enclosure has been fitted to the
wall.
To avoid damage to the
IDR-M mimic and to the fire
control panel ensure that
you follow these
instructions

IDR-M Mimic Installation & Commissioning Manual
Installation Guide
7 997-412-000-3, Issue 3
June 2005
2.3.2 What to do if Your Equipment is
Damaged or Suspect
If you have problems regarding the quality of
any supplied mimic components or this
manual, or items are missing, follow the
procedure below:
1DO NOT continue with the installation but
contact your supplier for advice on what to
do next.
Similarly, if the product is found tobefaulty
during installation contact your supplier
immediately.
2To aid your supplier and the manufacturer,
you are requested to note all the details
relevant to your complaint, date of receipt,
packaging condition, etc. and forward this
to your supplier.
3Where the product needs to be returned to
yoursupplier,youare requested to use the
original packaging wherever possible.
1
2
3