Honeywell PRO TH3110D User manual

PRO TH3000 Series
Non-Programmable Digital Thermostat
® U.S. Registered Trademark. Patents pending.
Copyright © 2009 Honeywell International Inc.
All rights reserved.
Installation
Guide
69-1929EFS-01
This manual covers the following models
•TH3110D: For 1 Heat/1 Cool systems
• TH3210D:For2Heat/1Coolheatpumpsystemsonly
(Pullthermostatfromwallplateandturnovertofindmodelnumber.)
System Types
TH3110D:
•Gas, oil, or electric heat with air
conditioning
• Warmair,hotwater,high-
efficiencyfurnaces,1Heat/1
Coolheatpumps,steam,gravity
• Heatonly
• Heatonlywithfan
• Coolonly
• 750mVheatingsystems
TH3210D:
• 2Heat/1Coolheatpumps
Must be installed by a trained, experienced technician
Readtheseinstructionscarefully.Failuretofollowtheseinstructions
candamagetheproductorcauseahazardouscondition.
Need Help?
Forassistancewiththisproductpleasevisithttp://customer.honeywell.com
orcallHoneywellCustomerCaretoll-freeat1-800-468-1502

Installation Guide
69-1929EFS—01 2
ENGLISH
MCR29390
PULL HERE
HIPS
M29389
Wallplate installation
Removethewallplatefromthe
thermostatasshownatleft,then
followdirectionsbelowformounting.
1. Pullwiresthroughwirehole.
2. Position wallplate on wall, level and mark
hole positions with pencil.
3. Drill holes at marked positions as shown
below,thentapinsuppliedwallanchors.
4. Place wallplate over anchors, insert and
tightenmountingscrews.
Pullatbottomtoremovethermostat
fromwallplate.
CAUTION: ELECTRICAL HAZARD
Cancauseelectricalshockorequipmentdamage.Disconnectpowerbeforebeginning
installation.
Drill3/16"holesfordrywall.Drill7/32"holesforplaster.
Wallanchors
Wirehole
MERCURY NOTICE
Ifthisproductisreplacingacontrolthatcontainsmercuryinasealedtube,donot
placetheoldcontrolinthetrash.Contactyourlocalwastemanagementauthorityfor
instructionsregardingrecyclingandproperdisposal.
Mountingscrews

PRO TH3000 series
3 69-1929EFS—01
ENGLISH
MCR29391
Power options
TH3110D Terminal block shown Connect CforprimaryACpower
(optionalifbatteriesareinstalled).
Keep wires in this
shaded area
Insertbatteriesforprimaryorbackuppower
TH3110D:
C 24Vaccommon.For2transformer
systems,usecommonwirefrom
coolingtransformer.
B Changeovervalveenergizedin
heating
R 24Vacpowerfromheating
transformer
Rc 24Vacpowerfromcooling
transformer
O Changeovervalveenergizedin
cooling
G Fan relay
Y Compressor contactor
W Heat relay
TH3210D:
C 24Vaccommon
B Changeovervalveenergizedin
heating
R 24Vacpower
L SendsoutputwhensettoEm.Heat
O Changeovervalveenergizedin
cooling
G Fan relay
Y Compressor contactor
Aux Auxiliaryheatrelay
E Emergencyheatrelay
Terminal designations
Wiring
Removefactory-
installedjumper
onlyfortwo-
transformer
systems.
CROGY
E
BAux L
M29393
CROGYWBRc
MCR29392

Installation Guide
69-1929EFS—01 4
ENGLISH
Wiring
2H/1C Heat
Pump System
TH3210D
C 24Vaccommon[3]
B Changeovervalveenergizedin
heating [5]
R Power [1]
L SendsoutputwhensettoEm.Heat[8]
O Changeovervalveenergizedin
cooling [5]
G Fan relay
Y Compressor contactor
Aux Auxiliaryheatrelay[9]
E Emergencyheatrelay[9]
1H/1C System
TH3110D
(1 transformer)
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power [1]
G Fan relay
Y Compressor contactor
W Heat relay
1H/1C System
TH3110D
(2 transformers)
C 24Vaccommon[3, 4]
R Power(heatingtransformer)[1, 2]
Rc Power(coolingtransformer)[1, 2]
G Fan relay
Y Compressor contactor
W Heat relay
See [notes] below
1H/1C Heat
Pump System
TH3110D [7]
C 24Vaccommon[3]
B Changeovervalveenergizedin
heating[5]
R [R+Rcjoinedbyjumper]
Rc Power [1]
O Changeovervalveenergizedin
cooling [5]
G Fan relay
Y Compressor contactor [6]
W [W+Yjoinedbyjumper]
Heat Only
System
TH3110D
C 24Vaccommon [3]
R [R+Rcjoinedbyjumper]
Rc Power [1]
W Heat relay
Heat Only
System with
Fan TH3110D
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power [1]
G Fan relay
W Heat relay
Cool Only
System
TH3110D
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power [1]
G Fan relay
Y Compressor contactor
NOTES
Wirespecifications:
 Use18-to22-gaugethermostatwire.
Shieldedcableisnotrequired.
[1] Powersupply.Providedisconnectmeans
andoverloadprotectionasrequired.
[2] Removejumperfor2-transformersys-
tems.
[3] Optional24Vaccommonconnection.
[4] Commonconnectionmustcomefrom
coolingtransformer.
[5] UseeitherOorBterminalsforchangeover
valve.
[6] Useasmallpieceofwire(notsupplied)to
connectWandYterminals.
[7] SetfanoperationswitchtoHeat Pump
(seepage5)andconfiguresystemtype
forheatpump(seepage6).
[8] L terminal sends a continuousoutput
whenthermostatissettoEm.Heat.
ConnecttoHoneywellzoningpanelsto
switchthepaneltoEmergencyHeat.
[9] InstallfieldjumperbetweenAuxandEif
there is no emergency heat relay.
Wiring guide — conventional and heat pump systems
CROGY
E
BAux L
M29393
CROGYW BRc
MCR29394
CROGYW BRc
MCR29395
CROGYWBRc
MCR29396
CR
O
WB Rc
MCR29397
CROGW BRc
MCR29398
CROGY BRc
MCR29399

PRO TH3000 series
5 69-1929EFS—01
ENGLISH
MCR29401
MCR29400
TH3110D only:
• Gas or Oil: For gas or oil heating
systems,leavethefanoperationswitch
inthisfactory-setposition.(Thissettingis
forsystemsthatcontrolthefaninacall
forheat.)
• Electric or Heat Pump: Change the switch
tothissettingforheatpumporelectric
heatsystems.(Thissettingisforsystems
thatallowthethermostattocontrolthefan
inacallforheat,ifafanwireisconnected
to the Gterminal.)
Align the 4 tabs on the wallplate with
correspondingslotsonthebackof
thethermostat,thenpushgently
untilthethermostatsnapsinplace.
Thermostat mounting
Setfanoperationswitch.
Pushexcesswirebackinto
the wall opening.
Plugwallopeningwith
non-flammableinsulation.
Fan operation settings

Installation Guide
69-1929EFS—01 6
ENGLISH
Setup
1
0
MCR29402
Followtheprocedurebelowtoconfigurethethermostattomatchthe
installedheating/coolingsystem,andcustomizefeatureoperationasdesired.
Setup function Settings & options (factory default in bold)
1System type
TH3110D only 0Gas, oil or electric heat with air conditioning
1Heatpump(5minutecompressorofftimeinheatingand
cooling)
5Heating cycle rate
(CPH:cycles/hour)
TH3110D only
5For gas or oil furnaces of less than 90% efficiency
1For steam or gravity systems
3For hot water systems & furnacesofover90%efficiency
9Forelectricfurnaces
[Othercyclerateoptions:2,4,6,7,8,10,11or12CPH]
6Auxiliary heat
cycle rate (CPH)
TH3210D only
5For gas or oil furnaces of less than 90% efficiency
1For steam or gravity systems
3For hot water systems & furnacesofover90%efficiency
9Forelectricfurnaces
[Othercyclerateoptions:2,4,6,7,8,10,11or12CPH]
8Emergency heat
cycle rate (CPH)
TH3210D only
9For electric emergency heat
1For steam or gravity systems
3For hot water systems & furnacesofover90%efficiency
5Forgasoroilfurnacesoflessthan90%efficiency
[Othercyclerateoptions:2,4,6,7,8,10,11or12CPH]
9Compressor
cycle rate (CPH) 3Recommended for most compressors [Othercyclerateoptions:1,2,4,5,or6CPH]
14 Temperature
display 0Fahrenheit
1Celsius
15 Compressor
protection 5Five-minute compressor off time **See page 8 [Other options: 0, 1, 2, 3 or 4]
Function
number Setting
To begin, press and hold the s and t
buttonsuntilthedisplaychanges. Press tto change settings.
Press stoadvancetonextfunction.
Press and hold tstoexitandsavesettings.
Installer setup

PRO TH3000 series
7 69-1929EFS—01
ENGLISH
10
0
Te st
MCR29403
Aftercompletingtheinstallersetup,pressthesbuttonagaintobeginasys-
temtest.Followtheprocedurebelowtotesttheheatingandcoolingsystem.
1. Set SYSTEM switch to Heat.
2. Press ttoturnonandchecksystems(seetable,below).
3. Press tuntilsystemsturnoff.
4. Set SYSTEM switch to EmHeat and repeat steps 2-3 above (TH3210D only).
5. SetSYSTEM switch to Cool and repeat steps 2-3 above.
6. Press and hold ts to terminate test at any time.
Installer system test
System switch
System test
number Systemstatus
10 Heating system 0 Heatandfanturnoff.
1 Heatturnson.
2 Auxiliaryheatturnson.
20 Emergency heat 0 Heatandfanturnoff.
1 Heatandfanturnon.
2 Auxiliaryheatturnson.
30 Cooling system 0 Compressorandfanturnoff.
1 Compressorandfanturnon.
70 Thermostat information
(forreferenceonly)
71 Softwarerevisionnumber(majorrevisions)
72 Softwarerevisionnumber(minorrevisions)
73 Configurationidentificationcode(major)
74 Configurationidentificationcode(minor)
75 Productionconfigurationdatecode(week)
76 Productionconfigurationdatecode(year)
System test System status
Shaded areas below apply only to TH3210D.
CAUTION: EQUIPMENT DAMAGE HAZARD
Compressorprotectionisbypassedduringtesting.Topreventequipmentdamage,
avoidcyclingthecompressorquickly.

Installation Guide
Honeywell International Inc.
1985DouglasDriveNorth
GoldenValley,MN55422
http://customer.honeywell.com
Automation and Control Solutions
® U.S. Registered Trademark.
© 2009 Honeywell International Inc.
69-1929EFS—01M.S.05-09
Honeywell Limited-Honeywell Limitée
35DynamicDrive
Toronto,OntarioM1V4Z9
Printed in U.S.A. on recycled
papercontainingatleast10%
post-consumerpaperfibers.
Compressor Protection(SetupFunction15):Forcesthecompressortowaitafewminutes
beforerestarting,topreventdamage.Duringthewaittime,themessageCoolOnorHeatOn
(heatpumpsonly)willflashonthedisplay.
Please contact your distributor to order replacement parts.
Cover plate assembly*................................................. PartNumber50002883-001
12 pack of medium cover plates*............................. PartNumber50007298-001
*Usetocovermarksleftbyoldthermostats.
Temperature Ranges
• Heat:40°to90°F(4.5°to32°C)
• Cool:50°to99°F(10°to37°C)
Operating Ambient Temperature
• 32°to120°F(0°to48.9°C)
Shipping Temperature
• -20°to120°F(-28.9°to48.9°C)
Operating Relative Humidity
• 5%to90%(non-condensing)
Physical Dimensions
• 3-13/16”Hx5-3/8”Wx1-1/4”D
 97mmHx137mmWx32mmD
Electrical Ratings
System Voltage(50/60Hz) RunningCurrent
Heat(1ststage) 20-30Vac 0.02-1.0A
(Powerpile) 750mVDC 100mADC
Emergencyheat 20-30Vac 0.02-1.0A
Auxiliaryheat 20-30Vac 0.02-1.0A
Cooling 20-30Vac 0.02-1.0A
Accessories & replacement parts
Special functions
Specifications

Série PRO TH3000
Thermostatnumériquenonprogrammable
®MarquedéposéeauxÉ.-U. Brevets en instance.
© 2009 Honeywell International Inc.
Tousdroitsréservés.
Guide
d’installation
Doit être installé par un technicien d’expérience ayant
reçu la formation pertinente.
Lireattentivementlesinstructions.Lefaitdenepaslessuivrerisque
d’endommagerleproduitoudeconstituerundanger.
Besoin d’aide?
Pourobtenirdel’aidesurceproduitHoneywell,prièredeconsulterlesiteWeb
http://customer.honeywell.comoudes’adresserauxServicesàlaclientèlede
Honeywell en composant le 1800468-1502
Le présent guide porte sur les modèles suivants :
• TH3110D:Poursystèmesà1étagedechauffage/1étagede
refroidissement
• TH3210D:Pourthermopompesà2étagesdechauffage/1étagede
refroidissementseulement
(Retirerlethermostatdelaplaquemuraleetleretournerpourtrouverle
numérodemodèle.)
Types de système
TH3110D:
• Gaz,mazoutouchauffage
électriqueavecclimatisation
• Airchaud,eauchaude,
appareilsdechauffageàhaut
rendement,thermopompesà1
étagedechauffage/1étagede
refroidissement,vapeuretgravité
• Chauffageseulement
• Chauffageseulementavec
ventilateur
• Refroidissementseulement
• Systèmesdechauffage750mV
TH3210D:
• Thermopompesà2étages
dechauffage/1étagede
refroidissement

Guide d’installation
69-1929EFS—01 2
FRANÇAIS
MCR29390
PULL HERE
HIPS
M29389
Installation de la plaque murale
Séparerlaplaquemuraleduther-
mostatcommel’indiquel’illustration
ci-contre,puissuivrelesdirectives
d’installation.
1. Fairepasserlesfilsparl’ouvertureréservée
auxfils.
2. Placerlaplaquemuralesurlemur,
mettredeniveauetmarqueraucrayon
l’emplacementdestrous.
3. Percerlestrousauxendroitsmarqués
àl’aided’uneperceuse,puisinsérerles
chevillesd’ancragefournies.
4. Apposerlaplaquemuralesurleschevilles,
insérerpuisresserrerlesvisdefixation.
Tirerlethermostatparlebaspourle
détacherdelaplaquemurale.
MISE EN GARDE : RISQUE DE CHOC ÉLECTRIQUE
Peutprovoquerdeschocsélectriquesouendommagerlematériel.Couper
l’alimentationélectriqueavantd’effectuerleraccordement.
AVIS SUR LE MERCURE
Silenouveauthermostatremplaceunancienrégulateurcontenantuncontactà
mercure,nepasmettrel’ancienrégulateurauxpoubelles.Communiqueravecle
servicelocaldecueillettedesdéchetspourobtenirdel’informationsurlerecyclageou
surlabonnefaçondedisposerd’unancienrégulateurcontenantuncontactàmercure.
Utiliserunemèchede3/16po
silemurestenplacoplâtre.
Ancragesmuraux
Troudufil Visdemontage
Utiliserunemèchede7/32po
silemurestenplâtre.