Honeywell HPTV24-E Series Technical manual

1. Overview
The HPTV24-E series are UL listed; AC video power supply and distribution units that are mounted in a
compact enclosure with eight convenient knockouts for field wiring. They provide a constant source of 24
VAC at 4 amps or 8 amps of total supply current. The HPTV2404-E, HPTV2408-E and HPTV2416-E
include four, eight or sixteen individual fused outputs that route power to operate CCTV cameras and
other video accessories. The HPTV2401-E is a single output power supply with no distribution board
included.
2. Specifications
•UL/cUL Listed Power Supplies
•Four, Eight or Sixteen individually (automotive style) fused 24 VAC outputs.
•AC Power and Individual Output LED Indicators (on select models).
•Built in transient protection.
•LED Indicator Lights:
– Input Power LED (Green) – ON indicates incoming input voltage
– Output Power LEDs (Red) – ON indicates blown output fuse
•Fuses
– Incoming Safety Fuse Blocks 3.15A, 250V
– Load Output Fuses, 5A, 250V
– Secondary Fuse, 3A, 250V (Automotive Style)
•Three conductor AC cord included
•Power ON/OFF disconnect switch.
•Hinged, vented enclosure with seven convenient knockouts.
•Mechanical Dimensions: 9”L x 8”W x 4.5”D (22.86cm x 20.32cm x 8.89cm)
•Operating temperature range: –4°F to +95°F (–20°C to+35°C), indoor use only.
NOTE:
– A readily accessible switched circuit breaker must be available to disconnect mains power as
required.
– Do not expose to rain or moisture.
– Replace fuses with fuses of same type and rating.
– Refer servicing to qualified personnel.
Honeywell Power
Model Number
Output
Voltage
Total Output
Current
Number
of
outputs
.
120VAC @ 60Hz
current draw
HPTV2401-E 24VAC 4 amps (100VA) 1 (PTC protected) 0.9 amps
HPTV2404-E 24VAC 4 amps (100VA) 4 fused outputs 0.9 amps
HPTV2408-E 24VAC 4 amps (100VA) 8 fused outputs 0.9 amps
HPTV2416-E 24VAC 8 amps (200VA) 16 fused outputs 1.8 amps
HPTV2401
-
E, HPTV2404
-
E, HPTV2408
-
E,
HPTV2416
-
E
UL listed AC Video Power Supplies
PN 113142416: A 1/13/14
Honeywell
12 Clintonville Road
Northford, CT 06472
http://www.honeywellpower.com

3. Installation Instructions
1. Pre-drill holes where Power Supply enclosure is to be mounted.
If the included AC cord is used, mount the enclosure in a secure location where the unit cannot be
accidentally unplugged.
2. Secure the enclosure to the desired location (indoor installation only) as shown in Figure 1.
3. Disconnect power to the branch circuit to which the power supply will be connected.
4. Place on and off switches(s) to the OFF position.
5. Connect incoming AC (120 VAC, 60Hz) into the incoming Fuse block input observing polarities (see
Figure 2). Connect ground leads as shown in Figure 2 and Figure 3.
NOTE: All 115V wiring must be routed so that it cannot touch 24V wiring; minimum spacing is 1/4”
(0.635cm).
6. Connect CCTV cameras (or other external loads) to appropriate terminals (example output 1 = 1P, 1N).
Route all 24V wiring at least 3/8 in. (0.953 cm) from 120V mains wiring (indoor installations only).
7. Power the branch circuit and place SW1 to the ON position. The green LED should illuminate indicating
24V is reaching the PCB.
8. The red LEDs illuminate only if a camera (load) is installed and the fuse is open. Remove a camera
output fuse to verify LED operation.
9. Secure the cabinet cover with metal screws to prevent access by unauthorized personnel.

Figure 3:HPTV2408
-
E and HPTV2416
-
E
(x2)
Figure 2:HPTV2404
-
E

WARNING: TO REDUCE THE RISK OF ELCTRIC SHOCK, DO NOT EXPOSE APPLIANCE TO
RAIN OR MOISTURE. RISK OF ELECTRICAL SHOCK AND/OR EQUIPMENT DAMAGE.
DISCONNECT POWER BEFORE SERVICING THIS APPLIANCE.
•For continuous protection against hazard, replace fuses only with exact type and rating.
•A readily accessible switched circuit breaker must be available to disconnect main power as
required.
•All 120V wiring must be routed so that it cannot touch 24V wiring; minimum spacing is 3/8”
(0.953”).
•Installation and servicing should only be made by qualified personnel; contains no user-
serviceable parts.
•Install in accordance with all local regulations and the National Electrical Code.
For additional information:
• Visit our website: http://www.honeywellpower.com
• Contact Technical Support: (877) HPP-POWR
• Email us: [e-mail]
Figure 4: HPTV2401-E