Honeywell PS-HL-138 BM Series User manual

1
PAK200467-HW_01A March 2020 2020 Honeywell Security
PS-HL-138xxBM Series : 13.8V dc Switch Mode Power Supplies
with Standby battery charging, fault monitoring & remote fault signalling
PS-HL-13805BM-4OP (5A / 4 x Fused Outputs) PS-HL-13810BM-8OP (10A / 8 x Fused Outputs)
FEATURES
High efficiency cost effective power supply range ideal for Access Control applications.
Featuring a regulated 13.8V dc output supplying continuous full rated current to load
and a universal mains voltage input. Standby battery recharging is achieved within 24h
for an 18Ah battery. Maximum battery life is assured using deep discharge protection
to prevent premature battery failure when operating in standby mode for extended
periods. Two sets of volt free contacts are provided to signal (i) loss of mains and (ii)
battery and loss of output faults. The 5A model is provided with 4 x 1.25A Fused
Outputs whilst the 10A model is provided with 8 x 1.25A Fused Outputs.
•Continuous full rated current to load
•18Ah Standby battery recharged to 80% within 24 hours
•Universal mains input voltage 90-264V ac
•High efficiency electronics for reduced running costs and lower operating
temperatures
•Installer safe design with all high voltage electronics fully shrouded
•Full electronic short circuit and overload protection on load output under mains
operation
•Mains transient protection circuit
•Lid and removal from wall tamper detection
•Green Mains present LED
•Red Fault LED
•Volt free contact signalling mains failure
•Volt free contact signalling output and battery faults
•Individually Fused Outputs
Honeywell Middle East
Emaar business Park, Tel: [phone]
UAE : www.honeywell.com

2
PAK200467-HW_01A March 2020 2020 Honeywell Security
COMPLIANCE
This power supply unit meets the essential requirements of the following European
Directives:
Low Voltage 2014/35/EU EMC 2014/30/EU WEEE 2012/19/EU RoHS
2011/65/EU
SPECIFICATION
Input Specification
Voltage (rated)
100-240V ac
Voltage (operating)
90-264V ac
Frequency
50-60Hz
Max current
See Model Specification Table overleaf
Mains Input Fuse
See Model Specification Table overleaf
Max standby Power
See Model Specification Table overleaf
Output Specification
Voltage
13.5 –14.2V dc (13.8V dc nominal) on mains power
10.0 –12.3V dc on battery standby
Max load current
See Model Specification Table overleaf
Ripple
150 mV pk-pk max
Load output Fuse
See Model Specification Table overleaf
Overload
Electronic shutdown until overload or short circuit
removed (under mains power only)
Standby Battery
Battery Type
12V Valve Regulated Lead Acid
Battery Capacity
See below under enclosure size.
Battery Charging Fuse
protection
See Model Specification Table overleaf
Mechanical
Model
PS-HL-13805BM-4OP
PS-HL-13810BM-8OP
Enclosure Dimensions
w x h x d (mm) [external]
355 x 330 x 80
390 x 410 x 80
Max Battery Capacity
1 x NP17 (18Ah)
2 x NP17 (18Ah)
Weight (kg) excluding
battery
4.3
5.42
Environmental
Temperature
-10 to +40°C (operating) 95% RH non-condensing
-20 to +80°C (storage)

3
PAK200467-HW_01A March 2020 2020 Honeywell Security
Model Specification Table
PS-HL-13805BM-4OP
PS-HL-13810BM-8OP
Max Output Current to load
5A
2 x 5A
Output Fuses* (20mm glass)
F5.0A (4 x 1.25A)
2 x F5.0A (8 x 1.25A)
Max Mains Input Current (at
90V ac)
2.0A
3.0A
Mains Input Fuse
(20mm 250Vac HBC)
T3.15A
T3.15A
Battery Fuse Protection
F5.0 A
2 x F5.0A
LOCAL INDICATORS
Local Indicators
MAINS LED (Green)
Mains present
FAULT LED (Red)*
Flashes (1s period) when: loss of mains, battery
disconnected, output fuse fail, battery fuse fail, output
short circuit or low output voltage
*For 10A model, only one Fault LED will be visible via front panel. Each module has
independent fault monitoring and signalling.

4
PAK200467-HW_01A March 2020 2020 Honeywell Security
CONNECTIONS
+LOAD 1,2,3,4
+ve voltage output to load equipment
-LOAD 1,2,3,4
-ve voltage output to load equipment
EPS Fault
Voltfree contacts for loss of mains indication
GEN Fault
Voltfree contacts for general faults (see signalling outputs)
+BATT
-BATT
+ve (Red lead) connection to standby battery
-ve (Black lead) connection to standby battery
SIGNALLING OUTPUTS
GEN Fault (general)
Open when battery disconnected, *output fuse fail,
battery fuse fail or output short circuit. (*Applies only to
O/P 1 of multiple fused units).
Rating: 0.1A @ 60V dc N/O volt free contact.
EPS Fault (mains)
Open when loss of mains for more than 10s.
Rating: 0.1A @ 60V dc N/O volt free contact.
Lid Tamper
Note: Contact open in when lid opened by normal
means or unit is removed from mounted surface
Rating: 3A @ 125V ac N/O volt free contact.

5
PAK200467-HW_01A March 2020 2020 Honeywell Security
INSTALLATION &COMMISSIONING
This unit is only suitable for installation as permanently connected equipment. The
PSU is NOT
SUITABLE for external installation. EQUIPMENT MUST BE EARTHED. Before installation,
ensure that external disconnect device is OFF. The PSU should be installed according to
all relevant safety regulations applicable to the application.
Mounting
1) Mount securely in correct orientation allowing minimum clearance –see diagram.
2) Route mains and low voltage output cables via different knockouts and/or cable
entry holes.
3) Use bushes and cable glands rated to UL94 HB minimum.
Mains Power Up
4) Attach correctly rated mains cable (minimum 0.5mm2[3A], 300/500V ac) and
fasten using cable ties.
5) Apply mains power. Check for 13.8V dc on load outputs. Check green Mains LED is
on.
6) Disconnect mains power.
Load Output
7) Attach correctly rated load cable and fasten using cable ties. Note polarity.
8) Apply mains power. Check green Mains LED is on.
9) NOTE: Red LED may be illuminated to indicate that no battery has been
connected. This is normal.
10) Verify load is operating correctly.
11) Disconnect mains power.
Standby Battery
12) Attach supplied battery cables to terminal block and battery.
NOTE: ensure correct polarity of battery connections: +ve use red lead, -ve use
black lead.

6
PAK200467-HW_01A March 2020 2020 Honeywell Security
13) Apply mains power. Check green Mains LED is on.
14) Check there is no fault indication on Red LED.
15) Disconnect mains power. Check that the batteries continue to supply voltage and
current to the load. The Green LED should be off.
NOTE: Batteries must have sufficient charge to supply the load
16) Reconnect mains power. Green LED should be on.
Tamper
17) Check that the tamper screw makes good contact with the mounting surface.
Check that the tamper switch is:
closed when the lid is closed, and the lid screw is fitted
open when the lid is open.
18) Close cover and secure using fastening screw(s) provided.
OPERATING INSTRUCTIONS
This unit is intended for use by Service Personnel only. There are NO USER
SERVICEABLE parts inside.
The green Mains LED will be illuminated whilst the mains supply is present. In the
event of a fault condition the red Fault LED will flash and the corresponding (EPS or
GEN) fault signal contacts will open.
PREVENTATIVE MAINTENANCE
This unit is intended for use by Service Personnel only. There are NO USER
SERVICEABLE parts inside.
There is no regular maintenance required of the PSU other than periodic testing,
calibration check and replacement of the standby batteries. Reference should be
made to the battery manufacturer's documentation to determine typical/expected
battery life with a view to periodic replacement of the battery.
CAUTION
Dispose of used batteries according to the battery manufacturer’s
instructions and all local and national regulations.

7
PAK200467-HW_01A March 2020 2020 Honeywell Security
This page has been intentionally left blank.

8
PAK200467-HW_01A March 2020 2020 Honeywell Security