Honeywell Xenon Ultra 1962 Series User manual

Xenon™ Ultra 1962x Series
Cordless Area-Imaging Scanner and Charge Bases
Scanner Models: 1962h, 1962g, 1962li
Quick Start Guide
1962-EN-QS-01 Rev (a-01) DRAFT
5/23
Prelim Draft, not for release

1
Agency Model: 1962
Note: Refer to your User Guide for information about cleaning
your device.
Getting Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Once the base is connected and powered up, follow the Link the
Scanner (page 6) instructions to link the scanner to the base.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.
Prelim Draft, not for release

2
!
Before you attempt to use, charge or replace the
battery in the device, carefully read all labels, markings
and product documentation provided in the box or
online at sps.honeywell.com. To learn more about
Battery Maintenance for Portable Devices, go to
honeywell.com/PSS-BatteryMaintenance.
Avant d’essayer d’utiliser, de charger ou de remplacer
la batterie de l’appareil, lisez attentivement toutes les
étiquettes, marquages et documentation du produit
fournis dans la boîte ou en ligne à sps.honeywell.com.
Pour en savoir plus sur l’Entretien de Batteries pour
Appareils Portables, consultez-le honeywell.com/
PSS-BatteryMaintenance.
Prelim Draft, not for release

3
Connecting the Scanner
USB:
Note: If you are charging the scanner using the USB cable, the
current available for charging is reduced and charge times
are increased. Charging via the power supply is faster.
Horizontal Base:
Universal Base:
Prelim Draft, not for release

4
Keyboard Wedge:
Horizontal Base:
Universal Base:
Prelim Draft, not for release

5
RS232 Serial Port:
Horizontal Base:
Universal Base:
Prelim Draft, not for release

6
Link the Scanner
Use the following procedure to configure all scanners so they
automatically connect to the base.
1. Scan the barcode on the base.
2. Place the scanner into the base.
3. Power cycle the base to complete the link and establish
communication between the base and scanner.
When the scanner is in the base, the green LED on the base
flashes to indicate the scanner’s battery is charging.
Unlink the Scanner
If the base has a scanner linked to it, that scanner must be
unlinked before a new scanner can be linked. Once the previous
scanner is unlinked, it will no longer communicate with the
base. Scan the Unlink Scanner barcode to unlink a scanner.
Unlink Scanner
Prelim Draft, not for release

7
Reading Techniques
The view finder projects an aiming beam that
should be centered over the barcode, but it
can be positioned in any direction for a good
read.
Standard Product Defaults
The following barcode resets all standard
product default settings.
USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. If you are using a Microsoft®
Windows® PC, you will need to download a driver from the Hon-
eywell website (sps.honeywell.com). The driver will use the next
available COM Port number. Apple® Macintosh computers rec-
ognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
Standard Product Defaults
USB Serial
Prelim Draft, not for release

8
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Keyboard Country
Scan the appropriate country code below to program the key-
board layout for your country or language. By default, national
character replacements are used for the following characters:
#$@[\]^‘{|}~ Refer to the ISO 646 Character Replacements chart
in your User Guide to view the character replacements for each
country.
USB PC Keyboard
USA (Default)
Belgium
Denmark
Finland
France
Prelim Draft, not for release

9
Note: For a complete list of country codes, see the User Guide for
your product.
Germany/Austria
Great Britain
Italy
Norway
Spain
Switzerland
Prelim Draft, not for release