Honeywell Lyric C2 User manual

Lyric™ C2 Wi-Fi
Security Camera
Quick Installation Guide
Home
Download the Honeywell Lyric app
NOTE: Have your WiFi password available and confirm your
router is dual-band and communicates at 2.4/5 GHz before
installation.
1 Make sure bluetooth is enabled on your
mobile device.
2 Search for Honeywell Lyric in the App Store
or Google Play.
3 Download the Honeywell Lyric app.
GET IT ON
Lyric

2
Launch the Lyric app
1 Launch the Lyric app.
2 Select the Lyric C2 WiFi Camera to
install, then create an account (if
necessary), or sign in to your Lyric
account.
3 Follow the instructions in the Lyric app to
name the camera and its location.
Connect the power cord
1 Plug the power cord’s USB end
into the wall outlet adapter.
2 Plug your camera into a power
outlet.
3 Wait until the LED on the
camera blinks blue (about 1
minute), then tap NEXT.
NOTE: If the LED turns solid red, it
means the connection mode timed
out. Unplug the camera and plug it
back in.
Installation
Lyric Water Leak &
Freeze Detector
Lyric C2 Wi-Fi
Camera
Lyric Round
Select a device to install
100%8:08 AM
Add New Device

2 3
Connect
Connect to Wi-Fi
Be sure you are on the same WiFi network
you wish to connect your camera to.
1 Choose your WiFi network from the
list. Tap NEXT.
2 Enter your WiFi password, if necessary.
Tap DONE.
NOTE: The camera will beep during some
steps in this process.
Connect to mobile device
1 Enable bluetooth on your mobile device.
2 The app will look for the camera.
• For one camera, it will connect
automatically.
• For more than one camera, the app will
prompt you to select one camera at a
time. Each camera has a unique MAC
ID printed on the back. Use that ID to
select the camera you want to connect.
3 A QR code will display in the app. To
connect your camera to the app, hold the
QR code approximately 36 inches
(715 cm) from the camera lens.
4 The camera LED turns purple and the
camera beeps.
NEXT
NEXT
2.7-5.9 in

4
Wi-Fi connection LEDs
During WiFi connection, the LED indicates the following.
LED Camera state
Blinking Green Connecting to WiFi network.
Solid Green Connected to WiFi network.
Solid Red (for 2
seconds)
Connection failed. LED will then turn solid purple.
Solid Purple QR Code scan complete.
Re-start “Connect to WiFi” on page 3.
Blinking Blue Camera has lost bluetooth connection. Unplug
camera and plug it back in. See “Connect the power
cord” on page 2 for instructions.
Placement
With stand
Place the camera in a desired location for viewing
and recording.
On the wall
You can also mount the camera directly to
the wall without the stand.

4 5
Operation
Lyric app experience
When you launch the application, live video from your
camera is displayed.
If you have multiple cameras, a list of them is displayed.
Select a camera from the list to view live video from that
camera.
Testing smoke/CO alarm detection
If your smoke or carbon monoxide alarm goes off and
your camera is on, it will send you an alert that a smoke
or CO alarm has been detected.
To test this feature, press and hold the Test button on
your smoke/CO detector for at least 5 seconds or 3
cycles of the detector’s alarm. A shorter test might not
trigger a sound event.

6
Camera overview
LED
indicator
Camera
lens
Power
cord
Stand/wall
mount
Backplate
and rubber
feet Reset hole SD card and slot
Reset
If your WiFi connection fails or you need to connect to a different WiFi network,
insert one end of a paperclip into the reset hole. Press and hold it for 10 seconds
until you hear a chirp.
SD card
The camera comes with an encrypted 8GB SD card installed. It stores images if the
camera’s connection to the cloud is lost. You can replace it with any compatible
SD card.

6 7
Status LED
The camera has an LED that gives device status.
LED Camera state
During installation
Blinking Blue Powered up. Ready to begin setup.
Solid Blue Connected to App. Ready to complete setup.
Solid Purple QR Code scan complete. Re-start Connect to WiFi
process.
Blinking Green Connecting to WiFi network.
Solid Green Connected to WiFi and operating.
Solid Red Setup timed out. Unplug camera, plug it back in, and
restart the process.
During operation
Blinking Green Connecting to WiFi network.
Solid Green Connected to WiFi and operating.
Blinking Red Not connected to WiFi.

8 9
FCC Regulations
§ 15.19 (a)(3)
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
§ 15.21
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
§ 15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For product available in the USA/Canada market, only channel 111 can be
operated. Selection of other channels is not possible.
This device is restricted to indoor use.

8 9
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
IC Regulations
This device complies with Industry Canada license-exempt RSSs. Operation is
subject to the following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may cause
undesired operation of the device.
This device is restricted to indoor use.
IC Radiation Exposure Statement:
This device complies with IC radiation exposure limits set forth for an uncontrolled
environment. This device should be installed and operated with minimum distance
of 20cm between the radiator and your body.
This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.

10 11
Need help?
• Web: yourhome.honeywell.com
• Email: [e-mail]
• Phone: 18006333991