Honeywell NEXPTZ-PD Operating instructions

- 1 -
NEXPTZ Camera
Explosion proof Security Camera
(High Speed Standard Type)
INSTALLATION & OPERATION GUIDE BOOK
ENG

- 2 -
1. Install and use this system after reading these instruction thoroughly.
2. Keep these instructions.
3. Install in accordance with the manufacture’s instruction.
4. Take care of all Cautions and Warnings.
5. Use stainless steel hardware to fasten the mount to outdoor surfaces.
6. Only use replacement parts recommended by the manufacturer.
RISK O F ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER(OR BACK).
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PRERSONNEL
Explanation of Graphical Symbols.
This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important
operating and maintenance(Servicing) Instructions in the literature
accompanying the appliance.
TO REDUCE THE RISK OF IGNITION DO NOT OPEN WHEN AN EXPLOSIVE
GAS ATMOSPHERE MAY BE PRESENT
WARNING: To reduce the risk of ignition of hazardous atmospheres, conduit runs
must have a sealing fitting or cable gland connected within PT 3/4 inches of the
enclosure.
WARNING: To reduce the risk of ignition of Hazardous Atmospheres,
disconnect the equipment from the supply circuit before opening.
Important Safety Instructions
ENG

- 3 -
WARNING: Gross weight of this system is about 30kg. Use caution when lifting
and installing. It is recommended you to wear proper non-slip gloves be worn during
installation.
Figure1.
Method of Installation
Standard Position Inverted Position
This system can be installed in a standard or inverted position or camera Housing only with
optional bracket as below Figure1.
When installed for inverted operation, the origin of camera shall be reconfigured through the
Camera function. There is no need to be adjusted physically but sunshield bracket may not
be functional at this case.
Methods of Installation
ENG

- 4 -
Install the product to Pedestal Mount bracket
To install this product, please refer to Figure2 and do the following steps.
1. Make sure the threads of the product and the threads of the supplied M8X15mm stainless steel bolts
(Supplied) are free of dirt and debris.
2. Apply an amount of thread locking compound(not supplied) to the thread of the product and the thread of
the bolts.
3. Secure the product to the mounting surface with the adjusted wrench and four M8x15mm stainless steel
bolts and lock washers. Tighten the bolts to 250~350 kgf.cm (24Nm~34Nm)
Figure2.
Note : Figure2 shows the product being installed on a Pedestal mount which is an optional
product (not supplied) and if there is no need the pedestal mount, just follow a above step to install
the product without pedestal mount bracket.
Methods of Installation
ENG

- 5 -
Figure3.
Note : Figure3 shows the product being installed on a surface with pedestal mount.
Install Product to the surface with Pedestal mount bracket
PT 3/4 “-14
Seal Fitting
(Not Supplied)
Explosion proof
Flexible conduit
(Not Supplied)
PT 3/4”-14 Nipple
(Supplied)
Fiber Filler Sealing
compound Cables
Sealing Method
To install this product, please refer to Figure3 and do the following steps.
1. Make sure the threads of the supplied four M10X30mm stainless steel bolts (Not Supplied) and flat/spring
washers are free of dirt and debris.
2. Apply an amount of thread locking compound(not supplied) to the thread of the product and the thread of
the bolts.
3 There are more options such as wall, corner and pole mount bracket to install. (refer to the mount bracket
part page)
4. Make sure the seal fitting(not supplied) and the threaded hole of this system are free of the dirt and
particles.
5. Assemble Nipple(supplied), the threaded hole of this system, seal fitting and flexible conduit(not supplied)
to be fasten firmly and then the cables must be passed through the seal fitting, nipple and flexible conduit.
Plus, the sealing fitting, flexible conduit should be acquired IECEx Certification.
Methods of Installation
ENG

- 6 -
Figure4.
Base Schematic of Installation
POWER
AC110 or 220V
BNC
MAIN MONITOR
DATA1 DATA2
+ - -+ + -
REAR
FRONT
KEYBOARD CONTROLLER
HTX-5000
REAR
DATA 2 DATA 1 DC 12V
RS 485
1 DOME 2
IN OUT DVR RS 232C
ALARM/DVR
DC 12V
SLAVE
RS 485 +
-Alram out
COM
N/O
RS 485
DVR
1. Figure4 is recommended for the base Schematic of Installation.
2. If you wish to consist of another method or other components, you must proceed to do after
conferring with a manufacture.
3. Depend on a DVR, you can control the product with an Utility in the DVR without HTX-5000.
Base Schematic
ENG

- 7 -
Configuration of Wire Harness
POWER
(AC 220V or 110V)
BNC
Alram
In/Out Put
RS-485
Data+, -
Figure8.
Cable configuration
2m ±0.3m
Cable Configuration
Wire Color Function Description
Brown
Sky Blue
Green
Power Input
(AC 100V ~ 240V)
L1
N
GND
Red
Orange
Yellow
Green
Black
Alarm Input
Alarm 1
Alarm 2
Alarm 3
Alarm 4
GND
Black
Red
Yellow
White
Alarm Output A
Alarm Output B
NO A
COM A
NO B
COM B
Black
(Coaxial cable) Video BNC Cable
Blue stripe
White stripe Control Data RS485 Data + RS485 Data -
ENG

- 8 -
Key Feature and Introduction
The NEXPTZ Series camera which is Explosive proof camera features a high resolution Super
HAD CCD imager for enhanced lowlight sensitivity. The NEXPTZ Series follow the stringent
explosion-proof requirements with creative mechanical strength and design. Moreover, the
NEXPTZ explosion-proof system is designed to meet the rigorous requirements of explosion-
proof electrical equipment installed in hazardous locations. The system has built-in True Day
&Night zoom camera with programmable Camera setting easy to setup and program functions.
System information aides trouble shooting by displaying the hardware and software version of
the dome driver, baud rate, and protocol.
The Highest level Ex Class : Ex d IIC T6 (IECEx, ATEX, CE, FCC, KC)
Corrosion resistant SUS 316 Construction
IP67 Protection
Adapt 650TVL, Optical x36 AF Zoom module
360ºContinuous Panning with max 60º/sec High Speed
Thanks to Flip function and 360ºcontinuous rotate at Pan/ Tilt angle
Various Preset function
- Home Function
- 128 Preset potions w/ focus, iris, BLC setting
- 8 Scan ,4 Tours, Pattern
Built-in Wiper function
4 Alarm in & 2 Relay out
Integrated with Washer jet : EXWJ400
Approx 30Kg of light weight
ENG

- 9 -
* This function is specialized to HTX-5000 keyboard.
RemarksResultsProcessFunction
-ZOOM IN
-ZOOM OUT
-Focus is changed to Near or Far
-Return to Auto Focus mode by
moving the joystick.
-Iris is opened or closed
Moving the joystick reactivates Auto Iris
mode
ZOOM
/FOCUS/
Iris
For matching ID 01
If ID set 02, press and (Cam)
button
You can see the moving as following the
direction.
①Press and (CAM) button
in sequence.
②Move Joystick to the right,
left, up and down.
PAN/TILT 1
①Twist Joystick to the right.
②Twist Joystick to the left.
③Press button.
④Press button.
2
If it’ not raining,
forbid to keep the
moving status over
1 hour continually.
-Wiper moves as keeping a steady angle.
-Wiper stops.
Wiper
Control
①Press (On) button or
Press and (On) button
in sequence.
(86+ Preset) at Pelco Protocol
②Press (Off) button or
Press and (Off) button
in sequence.
(79+ Preset) at Pelco Protocol
2
2
Water jet
(Optional)
①Set washing position
-.Move the window face to nozzle by
using pan/tile and save the position
on preset 59.
②Press and (On) button.
(88+ Preset) at Pelco Protocol
- Set the specific position to wash front
window toward the nozzle on preset 59.
-Run washing and wiping.
4
Check water level in
the tank periodically.
Simple Function Control Guide
ENG

- 10 -
①Press (Pattern) button to set.
(80+ Preset) at Pelco Protocol
②Press (Esc) button or move
Joystick to the right or left.
①Set Preset (direct)
-.Select one button of ~ ,
(128) and Press (Shift) and
(Preset) in sequence.
②Running Preset
-.Press Number button and
in sequence.
-PTZ moves to the position which you
have saved the preset.
~
Simple Function Control Guide
RemarksResultsProcessFunction
-Menu screen is displayed.
-Go into the sub-menu items.
Change value.
Navigate through the menu items
-Navigate through the menu items.
-Escape from the menu.
Menu
①Press (Menu) button.
(95+ Preset) at Pelco Protocol
②Move Joystick to the right
or left.
③Move Joystick Up or Down.
④Press (Menu) or (Esc)
or (Enter) button twice.
ESC
(Enter)
= (94+ Preset)
at Pelco protocol
(Menu)
= (95+ Preset)
at Pelco protocol
(ESC)
= (96+ Preset)
at Pelco protocol
Scan ①Press (Scan) button to set.
(60+ Preset) at Pelco Protocol
②Press (Esc) button or move
Joystick to the right or left.
Preset
-PTZ continually moves between the start
and end point which user set among the
preset.
-Escape from the moving Auto Pan.
ESC
1 1 2 8
Tour ①Press (Tour) button to set.
(70+ Preset) at Pelco Protocol
②Press (Esc) button or move
Joystick to the right or left.
ESC
1~59+ Preset to
operate Preset 1~59
at Pelco protocol.
-PTZ continually moves to user set
position of the presets.
-Escape from the moving Tour.
61~68+ Preset to
operate Scan1~8 at
Pelco protocol.
71~74+ Preset to
operate Tour1~4 at
Pelco protocol.
Pattern
ESC
-PTZ continually moves to user set
position of the presets.
-Escape from the moving Tour.
81~84+ Preset to
operate Pattern1~4 at
Pelco protocol.
ENG